BL-Touch to Alfawise U10

dc42

@pertti said in BL-Touch to Alfawise U10:

98 P"config.g"
Error: Bad command: 98 P"config.g"

You missed out the leading M.

Pertti

@dc42 I see... what do You mean by "missing out the leading M"?

dc42

@pertti you ran command:

98 P"config.g"

instead of:

M98 P"config.g"

Pertti

@dc42 Ok, I got it, thank You.

21.4.2022 klo 13.38.36 M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

dc42

@pertti does the BLTouch perform its self test when you power up?

Pertti

@dc42
Nope

Phaedrux

It sounds like the BLTouch is not getting power if it's not doing a self test. Does it light up?

Pertti

@phaedrux
No light. I´ll check the wires.

Pertti

@pertti The BL touch wire connector was 1 step aside in the motherboard.
I´ll continue the experiment soon.

Pertti

@pertti Now it gets power! At the start the Bl-touch moves back and forth . After homing it twinkles red light.
I have no idea weather the BL-touch is supposed to be the z-endstop or not. Is my configuration ok?

dc42

@pertti do M401 and M402 work to deploy and retract the probe?

Lo-Fi

@pertti Do you have a Z stop switch as well as the BLTouch? If not and you want to use the BL for Z homing, you'll want to change M574 Y1 S1 P"ystop" to M574 Z1 S2 in your config and define a Z homing macro.

This blog post here give an excellent overview of the macros:

https://betrue3d.dk/bltouch-on-duet-wifi-configuratio-and-usage/

Remove the M280 command in the config, that belongs in the Pin Down macro.

Pertti

@dc42 said in BL-Touch to Alfawise U10:

M401

M401 deploys an d M402 retracts the probe.

Pertti

@lo-fi Yes I have a remainig z endstop. I do not know is it worth saving. Less moving parts sounds good. And if I changed the bed surface thickness then it is easier to handle with z probe.

Phaedrux

Share your homeall and homez here and we can tell you if anything needs to change. In general though, to home Z with the probe you need a G30 command. And before the G30 you'd need a G1 X Y command to move the probe into position. Ideally the center of the bed.

Pertti

@phaedrux
I´ll check this, looks good. https://betrue3d.dk/bltouch-on-duet-wifi-configuratio-and-usage/

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Sun Mar 06 2022 15:03:52 GMT+0200 (Itä-Euroopan normaaliaika)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X-405 Y-405 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-405 Y-405 F360 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-505 F360 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Mar 07 2022 20:17:53 GMT+0200 (Itä-Euroopan normaaliaika)
G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 Z-505 F1800 ; move Z down until the endstop is triggered
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z5 F100 ; lift Z relative to current position
;G90 ; absolute positioning

Phaedrux

@pertti said in BL-Touch to Alfawise U10:

G1 H1 Z-505 F360 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

Remove those lines in homeall and replace them with

G90
G1 X150 Y150
G30

@pertti said in BL-Touch to Alfawise U10:

G1 H1 Z-505 F1800 ; move Z down until the endstop is triggered
G92 Z0 ; set Z position to axis minimum (you may want to adjust this)

And in homez, remove those lines and replace them with the same.

Pertti

@phaedrux
Thank You all! First testprints going on! So far so good. I removed the z endstop and replaced it with z-probe.