It's out! RepRapFirmware 2.0 and 1.21.1 released
-
is it just me... or if you have the web interface running on screen for a long time it is out of sync with the current status (I tell by looking at current z level location)
I had my big print on for a while and it tells me that I am at Z@ 11.xx but when I refresh the screen it is now changed to Z@17.xx
I never noticed that with the previous version
Thanks
Tony -
@otaku521 I too face the same problem - web interface shows a different value and I have to refresh the tab to see the current value.
In previous versions, it is either connected or disconnected. When it is connected, it is in sync with the actual print progress.
Cheers,
Vasan -
I have once seen the web interface think it is connected when the printer was not turned on. I think this was after I woke up the PC from sleep mode, but I am not sure. I was using FireFox browser.
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@dc42 said in It's out! RepRapFirmware 2.0 and 1.21.1 released:
I have once seen the web interface think it is connected when the printer was not turned on. I think this was after I woke up the PC from sleep mode, but I am not sure. I was using FireFox browser.
I can see this more often then not when waking up my PC from sleep and not having manually disconnected DWC before sending the PC to sleep. I am using Vivaldi which basically is the same as Chrome.
-
@bmmal said in It's out! RepRapFirmware 2.0 and 1.21.1 released:
To expand further on my issue of not getting responses, it seems that DWC is somehow getting out of sync but not disconnecting ie ..........
I am glad that I am no longer the only one.
I have the same problem.
The debugging mode shows a difference:
DWC 1.21.1 stops after error:
DWC 1.21 continues to run after error:
https://forum.duet3d.com/topic/5470/firmware-2-0rc6-and-1-21-1rc6-released/13
-
Using it on the Railcore since released, non stop printing while I'm awake, and zero issues.
-
I confirm the issue @zerspaner_gerd is seeing, have sometimes the same problem.
Reloading the page resolves the problem.
I suspect this is a DWC bug... -
@zerspaner_gerd : what is the value of the Ajax retries in your DWC settings?
-
@whosrdaddy
I tested at times until 4.
For a long time I stayed at 2, without change.Am current back to 3 high, and this seems to show an improvement currently.
Did you observe the same?
-
confused which files i need to use to upgrade to V2.0 for my duetwifi
lots of files listedDuet2CombinedFirmware.bin
5.6 KB DuetDriverFiles.zip
356 KB DuetMaestroFirmware.bin
552 KB DuetWebControl-1.21.1.zip
290 KB DuetWiFiServer.bin
57.9 KB iap.bin
57.8 KB iap4e.bin
58 KB iap4s.bin
370 KB RepRapFirmware-Alligator.bin
292 KB RepRapFirmware-RADDS.bin
373 KB RepRapFirmware.bin
335 KB Symbols-CoreNG-SAM3X8E.zip
322 KB Symbols-CoreNG-SAM4E8E_RTOS.zip
305 KB Symbols-CoreNG-SAM4S_RTOS.zip
110 KB Symbols-FreeRTOS-SAM4E.zip
81.7 KB Symbols-FreeRTOS-SAM4S.zip
1.67 MB Symbols-RepRapFirmware-Duet085.zip
1.5 MB Symbols-RepRapFirmware-Duet2_RTOS.zip
1.48 MB Symbols-RepRapFirmware-DuetM_RTOS.zip
Source code (zip)
Source code (tar.gz) -
@adamfilip What firmware version are you upgrading from?
Duet2CombinedFirmware.bin should work. If you haven't upgraded in a while you may need to rename it. Check the firmware release notes for the interceding firmware.
-
@adamfilip said in It's out! RepRapFirmware 2.0 and 1.21.1 released:
confused which files i need to use to upgrade to V2.0 for my duetwifi
Which firmware version are you using at present?
-
I tried the current Duet2CombinedFirmware.bin file and installed it. but this is what it says currently
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.0 or 1.01
Firmware Version: 1.21RC3 (2018-02-28 build 4)
WiFi Server Version: 1.21
Web Interface Version: 1.21.1 -
@adamfilip Perhaps this will help? https://forum.duet3d.com/topic/5646/duet-wifi-not-updating-firmware-when-installing-2-0/2
-
Hi Dave been a while.. I see things have really progressed since i pestered you last. LOL I am getting ready to upgrade so i can get wifi working again. Great to see the evolution and addition of ssid and pw btw! I see i have some firmware updates to do as well but it is all a little confusing. i was wondering if someone can give me a cliff notes version of what to do 1st.
Duet wifi running ver 1.18.1 with panel due v 1.15c PC and printer are in opposite ends of house so ideally do this via sd card? What do i do 1st? Also confused about which are the latest versions and where to get them. I am hoping to get my ducks in a row for this weekend . BTW, loved the tidbit from E3D on how great the duet is. I have another printer now, running mks 1.4 board and wow, it is a real dinosaur by comparison. I had no idea how lucky i was with my 1st system. I am currently building a system with 1540 mm X, and 1500 mm Y \ Z so looking forward to the Duet2 as well
-
@franknprinter Take a good look through this document.
https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware
You'll need to follow the special steps for updating to 1.19 as things changed slightly at that point.
-
Thank you, yes this was my issue.
-
I have downloaded the Duet2CombinedFirmware.bin, iap4e.bin, and DuetWebControl.zip files. I uploaded all of these to my DuetEthernet and it looked like it installed correctly, but it reports back saying that the firmware version is still 1.21. I'm running DWC 1.21.1, but I tried it with DWC 1.21 as well. Any idea what I'm doing wrong? The firmware updated date is listed as (2018-03-21), which is probably when I updated things last. Unfortunately the link above didn't solve my problem like I had hoped.
Edit: It works now. Tried it again after the 4th or 5th time and it just worked. I honestly cannot think of anything that changed.
-
thanks much @Phaedrux , i will give that a try this weekend!
-
So far so good, havent run into any issues with 2.0 so far
