Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Homeall Slams head to far corner

    Scheduled Pinned Locked Moved
    Tuning and tweaking
    4
    15
    480
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt
      last edited by fcwilt

      @mrenz999 said in Homeall Slams head to far corner:

      I re-posted your files using the </> tag - it improves readability and provides scrolling sections for each file.

      Please posts your other homing files that you say are working for you.

      Thanks.

      config.g

      config.g

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Tue Jun 16 2020 08:02:01 GMT-0700 (Pacific Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
G21 ; Set units to MM
M550 P"Duet 3" ; set printer name
M669 K1 ; select CoreXY mode

;Network
;M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0.0 S1 ; physical drive 0.0 goes forwards
M569 P0.1 S0 ; physical drive 0.1 goes backwards
M569 P0.2 S1 ; physical drive 0.2 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M569 P0.4 S0 ; physical drive 0.4 goes backwards
M569 P0.5 S1 ; physical drive 0.5 goes forwards
M569 P1.0 S0 ; physical drive 1.0 goes forwards
M584 X0.0 Y0.1 Z0.2:0.3:0.4 E0.5:1.0 ; set drive mapping
M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation
M92 X100.00 Y100.00 Z400.00 E408:408 ; set steps per mm
M566 X600.00 Y600.00 Z24.00 E300.00:300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X20000 Y20000 Z600 E2000.00:2000.00 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z600.00 E5000.00:5000.00 ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z1300 E1200:1200 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
M671 X-55:465:465 Y180:310:45 S9 ; leadscrews at rear left, front middle and rear right

; Axis Limits
M208 X Y0 Z0 S1 ; set axis minima
M208 X410 Y410 Z465 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"io4.in" ; configure active-high endstop for low end on X via pin !io0.in
M574 Y1 S1 P"!io1.in" ; configure active-high endstop for low end on Y via pin !io1.in
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
;M950 S0 C"io7.out" ; create servo pin 0 for BLTouch
;M558 P9 C"^io7.in" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds height + speeds
;G31 P500 X-40 Y-10 Z1.192 ; set Z probe trigger value, offset and trigger height
;M557 X20:430 Y15:410 S20 ; define mesh grid
Z-Probe
M558 P8 C"^io7.out" H10 F120 T6000
G31 P50 X16.795 Y25.4 Z.3
M557 X20:400 Y20:400 S50

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"temp1" Y"thermistor" T100000 B4388 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S300
M307 H0 R0.276 C683.100:683.100 D0.20 S1.00 V24.1 B0
M307 H1 R2.032 C110.1 D4.50 S1.00 V24.2

; Fans
M950 F0 C"out7" Q500 ; create fan 0 on pin out7 and set its frequency
M106 P0 S1.0 H1 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"out8" Q500 ; create fan 1 on pin out8 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off
M950 F2 C"out9" Q500 ; create fan 2 on pin out9 and set its frequency
M106 P2 S1 H-1 ; set fan 2 value. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Tools
;M563 P1 D1 H1 F0
;G10 P1 X0 Y0 Z0
;G10 P1 R0 S0

; Custom settings are not defined

; Miscellaneous
T0
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
M501

      homeall.g

       ; generated by RepRapFirmware Configuration Tool v3.1.1 on Thu Jun 04 2020 11:20:25 GMT-0700 (Pacific Daylight Time)
 G91 ; relative positioning
 G1 H2 Z5 F6000 ; lift Z relative to current position
 G1 H1 X-500 Y-500 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
 G1 H1 X-500
 G1 H1 Y-500
 G1 X5 Y5 F6000 ; go back a few mm
 G1 H1 X-500 Y-500 F360 ; move slowly to X and Y axis endstops once more (second pass)
 G90 ; absolute positioning
 G1 X222 Y201 F9000 ; go to first bed probe point and home Z
 G30 ; probe the bed

      bed.g

      ; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v3.1.1 on Thu Jun 04 2020 11:20:24 GMT-0700 (Pacific Daylight Time)
M561 ; clear any bed transform
G28 ; home
;M401 ; deploy Z probe
G30 P0 X10 Y180 Z-99999 ; probe near an adjusting screw
G30 P1 X360 Y310 Z-99999 ; probe near an adjusting screw
G30 P2 X360 Y60 Z-99999 S3 ; probe near an adjusting screw and calibrate 3 motors
;G29
;M402 ; retract probe

      Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

      mrenz999undefined 1 Reply Last reply Reply Quote 0
      • mrenz999undefined
        mrenz999 @fcwilt
        last edited by

        @fcwilt

        ; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sat Jun 13 2020 19:59:21 GMT-0700 (Pacific Daylight Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 X-530 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000       ; go back a few mm
G1 H1 X-530 F360  ; move slowly to X axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning


        ; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v3.1.3 on Sat Jun 13 2020 19:59:22 GMT-0700 (Pacific Daylight Time)
G91               ; relative positioning
G1 H2 Z5 F6000    ; lift Z relative to current position
G1 H1 Y-530 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F6000       ; go back a few mm
G1 H1 Y-530 F360  ; move slowly to Y axis endstop once more (second pass)
G1 H2 Z-5 F6000   ; lower Z again
G90               ; absolute positioning


        
; homez.g

; called to home the Z axis
; generated by RepRapFirmware Configuration Tool v3.1.1 on Thu Jun 04 2020 11:20:25 GMT-0700 (Pacific Daylight Time)

G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 X222 Y201 F9000 ; go to first bed probe point and home Z
G30 ; home z by probing the bed
        fcwiltundefined 1 Reply Last reply Reply Quote 0
        • fcwiltundefined
          fcwilt
          last edited by

          @fcwilt said in Homeall Slams head to far corner:

          M574 X1 S1 P"io4.in"
          M574 Y1 S1 P"!io1.in

          Why is one of these inverted and not the other?

          Did you verify that each is working by manually triggering them and running M119?

          Frederick

          Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

          mrenz999undefined 1 Reply Last reply Reply Quote 0
          • fcwiltundefined
            fcwilt @mrenz999
            last edited by

            @mrenz999

            I forgot to mention that issue with G32 having the same problem is bed.g issues G28 which runs homeall.g which is where the problem is.

            Frederick

            Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

            mrenz999undefined 1 Reply Last reply Reply Quote 0
            • mrenz999undefined
              mrenz999 @fcwilt
              last edited by

              @fcwilt both work correctly. Different end stop switches.

              1 Reply Last reply Reply Quote 0
              • mrenz999undefined
                mrenz999 @fcwilt
                last edited by

                @fcwilt so remove the G28 ?

                Vetiundefined fcwiltundefined 2 Replies Last reply Reply Quote 0
                • Vetiundefined
                  Veti @mrenz999
                  last edited by

                  @mrenz999 said in Homeall Slams head to far corner:

                  so remove the G28 ?

                  no fix the problem in homeall.g

                  1 Reply Last reply Reply Quote 0
                  • fcwiltundefined
                    fcwilt @mrenz999
                    last edited by

                    @mrenz999 said in Homeall Slams head to far corner:

                    @fcwilt so remove the G28 ?

                     G1 H1 X-500 Y-500 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
 G1 H1 X-500
 G1 H1 Y-500
 G1 X5 Y5 F6000 ; go back a few mm

                    Why do you have lines 2 and 3?

                    Frederick

                    Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                    1 Reply Last reply Reply Quote 0
                    • Vetiundefined
                      Veti
                      last edited by

                      @fcwilt said in Homeall Slams head to far corner:

                      Why do you have lines 2 and 3?

                      that for corexy because they cant move independently.

                      execute each line of homeall separately and see where the problem is

                      fcwiltundefined mrenz999undefined 2 Replies Last reply Reply Quote 0
                      • o_lampeundefined
                        o_lampe @mrenz999
                        last edited by

                        @mrenz999 said in Homeall Slams head to far corner:

                        G1 X222 Y201 F9000 ; go to first bed probe point and home Z
                        G30 ; probe the bed

                        Is that the line that makes your head crash?
                        Why probe at X222 Y201?

                        mrenz999undefined 1 Reply Last reply Reply Quote 0
                        • fcwiltundefined
                          fcwilt @Veti
                          last edited by

                          @Veti said in Homeall Slams head to far corner:

                          execute each line of homeall separately and see where the problem is

                          This isn't my problem - @mrenz999 was the OP - I'm just trying to help him.

                          Frederick

                          Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                          1 Reply Last reply Reply Quote 0
                          • mrenz999undefined
                            mrenz999 @o_lampe
                            last edited by

                            @o_lampe To probe the center of the bed.

                            1 Reply Last reply Reply Quote 0
                            • mrenz999undefined
                              mrenz999 @Veti
                              last edited by

                              @Veti So this is what I did. One line at a time. Commented out the first line G92 and it works correctly now. Strange.

                              fcwiltundefined 1 Reply Last reply Reply Quote 0
                              • fcwiltundefined
                                fcwilt @mrenz999
                                last edited by

                                @mrenz999 said in Homeall Slams head to far corner:

                                @Veti So this is what I did. One line at a time. Commented out the first line G92 and it works correctly now. Strange.

                                I don't see a G92 in your homeall.g file.

                                Is that where it was?

                                Frederick

                                Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6

                                1 Reply Last reply Reply Quote 0
                                • First post
                                  Last post
                                Unless otherwise noted, all forum content is licensed under CC-BY-SA