@curieos said in M116 Hanging after M568 Error:

@dc42 This is in SBC mode, can I just upload these to the FW directory and send the update commands?

As you have already installed 3.5.0-rc3 from the package server, yes you can. However, to get the full fix you will need a DSF update too. We expect to release rc4 very soon.

@R006 see https://docs.duet3d.com/en/Duet3D_hardware/Duet_3_family/Duet_3_Mainboard_6HC_Hardware_Overview -- three led flashes means the firmware crc check failed. Most likely you either had a failure at the end of the build running crcappender or you weren't able to properly flash your build.

Try recovering your board with a firmware build from Duet3D using Fallback method #2 https://docs.duet3d.com/en/User_manual/RepRapFirmware/Updating_firmware#fallback-procedure-2 and then post the output of yout firmware build run here using the </> button to keep the terminal formatting.

@silverpoint In the meantime please share your config.g because I don't think DCS should fail to connect to RRF even if DSF cannot handle certain axis letters yet. You can email it to christian@duet3d.com as well if you don't want to make it public.

@soare0 said in Is it possible to upgrade a SoC on an old Duet 0.6:

Still, the enthusiasm is to be admired!

Oh yes, very much so!

Ian

@Phaedrux said in duet maestro fw 2,05:

@luca-f13 said in duet maestro fw 2,05:

how do I access the configurator?

https://configtool.reprapfirmware.org/

This may prove useful as well since it's been so long.

https://docs.duet3d.com/en/How_to_guides/Getting_connected/Getting_connected_to_your_Duet

thank you, you were very kind

@Mr-Crispin I’d first update DWC to the version that ships with firmware rc1, and see if that fixes the error. Or preferably update both firmware and DWC to the latest release: https://github.com/Duet3D/RepRapFirmware/releases

Ian

@T3P3Tony Under Firmware installation. Just keyed in "YAT". I found a lot of problems with YAT but not where to find the program.

Carl

See https://docs.duet3d.com/en/User_manual/RepRapFirmware/SD_card#sd-card-structure for a full overview of what you need besides the sys folder and main system macros (/filaments, /firmware, /macros, /menu, and /www folders, the latter with the duet web control files).

I may have fixed this already. I noticed in the log the SPI buffer warning. I increased the SPI buffer in raspbian to 8192 and now it seems to be working. But, my config must be totally broken in this version as I can't seem to power on my PSU anymore due to no PS_ON port defined. Off I go down the rabbit hole. 🙂

edit: config fixed by changing M80 to M80 C"pson"

@vjysnkr58 it can't run RRF and would need a board change.
Best to reach out for support on somewhere such as the marlin discord

@Phaedrux I don't have access to the DWC. I'll follow the steps below. Thank you.

@Boxy I will drop you an email - this looks like quite a specific and potentially far reaching set of changes.

Kept looking for info on the 1st problem...
Found this and fixed it.
https://forum.duet3d.com/topic/34638/sudo-apt-dist-upgrade-doesn-t-update-main-board

I am still getting the error about the plug in service not running....
But again will keep looking for a fix for this.

@racitup It turns out I had deployprobe.g and retractprobe.g in sys which was causing the issue.

v1.26.1 (2.05.1) now appears to be working okay.

@oliof Thanks for your help but I'm going to stick with 3.4.6 for now and try to simplify and rewrite my macros at a latter time.

@chrishamm The new config tool is still letting me choose stealthchop when Duet 2 WiFi/Ethernet/SBC is selected as board type. Maestro does support stealthchop and spreadcycle.

Ian

Fallback procedure #1 worked.... no idea why the normal procedure did not work

@DocTrucker said in "sudo apt dist-upgrade" Doesn't update main board?:

@jay_s_uk that got it, thanks.

Can someone update the documentation to add a note relating to this to step 6?

https://docs.duet3d.com/User_manual/Machine_configuration/SBC_setup

@droftarts Not a bad idea?

@FrodeBNilsen MIR is documented in the github link I posted in my reply: https://github.com/Apsu/Mir

See this video for a run on my prototype (would need proper re-engineering to work, time I dont seem to find): https://streamable.com/vczvhu

My config from back then is at https://github.com/oliof/printerconfigs/tree/main/minimir

Regarding larger PEI sheets: I got nothing on this, I am more into small printers.