@Phaedrux
; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.0.3 on Thu Sep 05 2019 15:50:44 GMT-0400 (Eastern Daylight Time)
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Tall Printer" ; set printer name
M665 R180 L160 B130 H580 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; put your endstop adjustments here, or let auto calibration find them
M575 P1 S1 B57600
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z80.00 E410.00 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z18000.00 E1200.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1100 Y1100 Z1100 E900 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 Z0 S1 ; set minimum Z
; Endstops
M574 X2 S1 P"!xstop" ; X active low and disabled endstop
M574 Y2 S1 P"!ystop" ; Y active low and disabled endstop
M574 Z2 S1 P"!zstop" ; Z active low and disabled endstop
; Z-Probe
M558 P5 C"zprobe.in+zprobe.mod" R0.4 H5 F1000 T6000 B1 ; set Z probe type to effector and the dive height + speeds
G31 P100 X0 Y0 Z-.15 ; set Z probe trigger value, offset and trigger height
M557 R130 S20 ; define mesh grid
; Temperature Sensors
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.06e-8 ; define E0 temperature sensor
; Heaters
M950 H0 C"bed_heat" T0 ; heater 0 uses the bedheat pin, sensor 0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
M307 H0 B0 S1.00
M140 H0
; Fans
M950 F2 C"fan2" Q500 ; Hot end fan
M106 P2 T45 H1
M950 F0 C"fan0" Q500 ; Part Cooling fan
M106 C"PartFan" P0 S0 H-1 B1
M307 H0 ; report the process parameters for heater 0
M307 H0 R2.186 K0.17:0.11 D5.67 S1.00 V24.0 ; set the process parameters for heater 0
; Tools
M563 P0 H1 F0 D0 T0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
M501 ; recall last used parameters
I see there is M552 S1 in my config, silly me. Mainly, what I was doing was accessing the printer through USB to give it the command
M588 S"*" (to delete all known networks)
then using
M552 S0 (networking idle mode)
M589 S"TallBoyPrinter" P"Kaoken123" I192.168.10.1 (To set it to AP mode and assign it a static IP)
then
M552 S2 (to set it as access point)
I will then disconnect USB and power the printer
But, like you showed me, I think that was all for nothing since the other M552 command is in config. Do I just need to set M552 S2 in my config instead?