Topics created by br7408

@dc42

Excellent. I actually did more digging around last night and found one of your posts in another forum from many years ago recommending this. I will try it and report back. Your sensor is absolutely the best one out there in my opinion, so I will be happy to get it working on this machine.

UPDATE: That did the trick David. It is now booting in digital mode. Thank you.

@o_lampe I need to run a minimum jerk of 10 in order to print radials smoothly. I find it could come into play at short corner moves... That or even a way to reduce jerk on short moves. I doubt IS would fix it, as you say.

Then again my only remaining issue with resonance is on the Y axis. I believe it is due to a tiny amount of belt stretch, as this is a big printer.

@br7408 said in Stealthchop & Speadcycle:

It is my understanding that under this software version, my steppers by default are full-time on speadcycle?

Correct. See D parameter of M569: to https://docs.duet3d.com/User_manual/Reference/Gcodes#m569-set-motor-driver-direction-enable-polarity-mode-and-step-pulse-timing

The default is spreadCycle for all drivers from RRF 3.4

Ian

@br7408 It looks like the heightmap wasn't reloaded but the scale was updated. Does it change when you press F5? If it happens again, please open the JS console (dev tools) via F12 and look for error messages.

@br7408 I used normal size countersunk screws and 2 to 3mm above the existing touch probe.

@deckingman

Hi Ian. I was looking into that, as well as PID fan compensation. My part cooling fan is run off of the main board, through a CPAP tube. I also reasoned that this hotend would likely benefit from a heatsock/insulator but the Slice offering is about $50 USD.

I built this printhead purely for a promotion, so I just need it to run well enough for now to get a print or two out of it. I will work out a more efficient implementation later.

@T3P3Tony said in 3 Bed Scanner Questions:

@becky9 thanks for the feedback. The spring steel plates i tested on my toolc hanger (which has a Mandala Roseworks Bed with strong magnets on it) do not show the point magnets through. Once of those is a generic spring steal bed, the other is a Wham Bam one (quite old though, not sure when i first got it)

Thanks for the info. I am using the Mandala Rose Works bed with WhamBam pex sheets. Hopefully I’ll have similar experience.

@gloomyandy

Thanks!

@dc42 That fixed the heater problem.

Still having issues with the wifi randomly dropping, and also getting disk almost full warnings, despite my SSD card only being half full.

@T3P3Tony Good point; I didn't think of using the command line console

@Phaedrux said in Driver 0 Phase May Be Disconnected:

Have you sent the email yet?

Working on that right now.

@Phaedrux Just updated yesterday

@droftarts Excellent! Thanks for clarifying that. I do already have a fuse provision on my 24V line so I should be gtg.

@br7408 Probably the best way to do this is just to run a test print (maybe one designed to test input shaping like this one https://www.klipper3d.org/prints/ringing_tower.stl) and vary the input shaper selected and settings during the print.

@Phaedrux So interesting enough today, I did one small print and was actually getting intermittent yellow error messages the whole time it was printing about Phase A and/or Phase B of '0' being disconnected. It printed fine though.

@Exerqtor No worries... I dug all over this forum looking for PA methods and never came across that post, strangely. Should be a sticky IMO.

@deckingman
Between the two of us I think we've added a significant amount of complexity to solve a rare event that is easily handled by proper care and attention by the operator.
Feels like I've been to another OHSA meeting 😂😂