Mesh Grid Compensation

Puppet172

@dc42
Yes I tried that too got the pretty much the same this as the last one I just posted.

dc42

@puppet172 said in Mesh Grid Compensation:

@dc42
Yes I tried that too got the pretty much the same this as the last one I just posted.

I meant this one:

To test this, place the nozzle over the bed and send G1 Z5 and G30 S-1 alternately. The G30 S-1 command should report about the same trigger height each time. If it reports increasing trigger heights, you are probing too fast. Reduce the F parameter in the M558 command until you get a consistent result.

Puppet172

@dc42
Yes it would go up a little by little like 4.303 to 4.350 and so on, sometimes it would eventually level out i then changed the F from i think 120 to 100 and then it seemed to level out right away to about .01 of a mm

dc42

What M201 and M203 Z parameters are you using, and what is your Z steps/mm?

Puppet172

@dc42
M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
M92 X80 Y80 Z2000 E100.1 ; Set steps per mm
M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z100 E1200 ; Set maximum speeds (mm/min)
M201 X500 Y20 Z350 E250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30

dc42

Your Z acceleration in M201 looks very high for 2000 steps/mm. I suggest you reduce it to around 40. OTOH your Y acceleration looks very low for 80 steps/mm.

Puppet172

@dc42 I think you got my m92 and m201 mixed up because my m92 z is 2000 but my m202 isn’t

dc42

@puppet172, I was referring to your M201 Z350.

Puppet172

@dc42

What would you recommend putting it at ?

dc42

40, as I said before.

Puppet172

@dc42
I will put it at 40 and then I will do another mesh bed and then post it

Puppet172

@dc42

Nylkos

Did you set you Z by "Home Z" or do you adjust with a piece of paper and G92 Z0?

I might be wrong but if your home Z and your offset isn't setup, that could cause the issue if before running M92 you your whole M92 should be off.

I will explain, if you home with your probe and your 0 is really 3mm, you then home with a piece of trigger and fix the difference but that will cause that when you run M92 and your probe triggers, they will assume that your are always minimun 3mm off...

Puppet172

@nylkos
how do i set the offset?

dc42

What type of Z probe are you using?

Puppet172

@dc42
uxcell LJ12A3-4-Z/AX 3-Wire DC6-36V 300mA NPN NC 4mm Inductive Proximity Sensor Switch https://www.amazon.com/dp/B00S50O152/ref=cm_sw_r_cp_api_OUWEBb2TQTHR5

Phaedrux

You can find your trigger height with this

https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe#Section_Calibrate_the_Z_probe_trigger_height

dc42

Please post your complete config.g, homeall.g and homez.g files, and tell us how you have connected the inductive sensor to the Duet.

Puppet172

@dc42
Sorry for the late response

0_1535219144684_homeall.g

0_1535219157439_config (2).g

0_1535219167488_homez (1).g

and the way i have it hooked up is its Positive and negative wires are hooked up to the 12v power supply because it needs at least 6 volts i think and then its other wire going to the z probe input.

dc42

I'm sorry for the delay in looking at this, things are hectic right now with new firmware development.