My prints are in mirror, but the axis are good.

mickey30m

@phaedrux
this is how it is now.
everything is done like the wiki.

; Drives
M569 P0 S0 ; Drive 0 goes backwards - x motor
M569 P1 S1 ; Drive 1 goes forwards - y motor
M569 P2 S0 ; Drive 2 goes backwards - left z motor
M569 P3 S1 ; Drive 3 goes forwards - extruder 1
M569 P4 S0 ; Drive 4 goes forwards (Z2 in the E1) - right z motor

5_1525128618496_homez.g

4_1525128618496_homey.g

3_1525128618496_homex.g

2_1525128618496_homeall.g

1_1525128618496_config.g

0_1525128618495_bed.g

Phaedrux

So it definitely looks like you have it configured for Y max homing, but simplify 3D is set for Y min homing.

dc42

@mickey30m said in My prints are in mirror, but the axis are good.:

@dc42 https://photos.app.goo.gl/9eERlnDNRr4xtmty1

That's a left-hand coordinate system, which explains your problem. Tell S3D to flip the Y axis.

mickey30m

@dc42 that have i changed. Before was IT also in mirror.

I Just flip it tot test it. I had it before on right hand

But same prints.

I will change it now.

mickey30m

I now slice it with cura the new version.
Default settings.
And Also prints in mirror. With a 0.06 later height so its printing for a long time now ;-).
But a Nice print. But in mirror :')

mickey30m

okay

just for sure, i take photos from all my settings and download my config file.

https://photos.app.goo.gl/OLfa5DH2pnX90JBi2
0_1525205946994_config.g

when everything is homed i get this in webcontrol
https://photos.app.goo.gl/ZJxTiC9zjXVzdQwL9

Machine Status
Head Position X Y Z
15.0 280.0 14.95
Extruder Drives Drive 0
n/a 0.0
Sensors Vin Z-Probe Fan RPM
11.8 V 0

dc42

Are you absolutely certain that when you press the X+10 button the head moves to the right, and when you press Y+10 it moves towards the rear of the printer i.e. away from you?

mickey30m

@dc42
https://photos.app.goo.gl/I6pkMGxCEYRMDCmm2

see this video.

first i home twice (because y dont wont go in 1 time) (i ask for this later)

than i push
5 times on X+10
5 times on Y+10
5 times on Z+10

dc42

You have set your printer up with a left hand coordinate system. If +X is to the right, then +Y must move the head towards the rear relative to the bed. As it is the bed that is moving, +Y should move the bed towards you.

You will need to reverse the direction of the Y motor (M569), change the configuration of the Y endstop from low-end to high-end or vice versa (M574), and change homey.g and homeall.g to home in the opposite Y direction.

mickey30m

@dc42

Sorry for the misunderstanding.

I think now everything is working good...
i go make a print and lett you know..

but what a super nice board is it....

first it is a little bit looking for everything.

but change homex.g and no need to reboot or whatever....
damnnn

In the beginning I thought it was a lot of money for a new board. but after a bit of looking around and reading. I was up. and now I am completely up. and I regret that I did not switch sooner ...

soon to buy two more for a DIY project.

Super thanks

dc42

Glad to help!