Duet Wifi Webserver not responding

daveidmx

Got it! I will report back tomorrow.

daveidmx

I didn't get as much testing in today as I'd hoped, but I haven't seen any connection resets so far. Yesterday it was as often as 10 minutes, or as rare as 6 hours. I've had about 2 hours of prints so far today, so… looking good so far?

ShiftingTech

Does the DuetEthernet still use this, or is there something else equivalent that we DuetEthernet folk should be trying out?

dc42

Duet Ethernet doesn't use the DuetWiFiServer.bin file. If you are getting disconnections on the Duet Ethernet and they only happen when you are homing the printer or when printing a file, run M122 after you reconnect and check the MaxReps figure in the report. Note: MaxReps gets reset back to zero after you run M122.

ShiftingTech

I think my disconnects have all been during print processes, but I'm not super confident in that statement. I will look into the maxreps thing. While I'm waiting for another disconnect event, can you explain what the maxreps means? And is any non-zero value bad, or…?

dc42

MaxReps figures above about 50 are bad. The value gives an indication of the interrupt load of the step pulse generator. If it gets too high then the http responder gets starved of CPU time.

ShiftingTech

Got it, thanks.

I just had an ethernet drop out, and when I did an M122 afterwards, I got a maxreps of 4. So I'm guessing that's not my problem…

daveidmx

Sad news on my front. I'm still seeing the web console stop responding on 1.21RC4. Looks like the same issue still. The packet trace shows the same pattern as before (HTTP GET followed immediately by a connection reset) and the console indicates the same message ("refused conn on port 80 no free conn").

I tried to do an [c]M586 P0 S0[/c]/[c]S1[/c] cycle and it looks like it might have crashed the WiFi module. My print froze and I got this on the console:

M586 P0 S0
HTTP is disabled
ok
WiFi:
ESP reported status change
WiFi: Soft WDT reset
ESP reported status change
WiFi:
WiFi: ctx: cont
WiFi: sp: 3fff2fc0 end: 3fff32c0 offset: 01b0
WiFi:
WiFi: >>>stack>>>
WiFi: 3fff3170:  40233576 00000030 0000001c 40225893
WiFi: 3fff3180:  40225d11 3fff6cac 3fff5b3c 40225a2b
WiFi: 3fff3190:  00000003 3fff31d0 00000000 40105f8d
WiFi: 3fff31a0:  00000050 000000ff 00000000 00000000
WiFi: 3fff31b0:  3fff2125 3fff2190 3fff2194 00000000
WiFi: 3fff31c0:  00000000 3fff211c 3fff1900 40106542
WiFi: 3fff31d0:  00000000 005000ff 20000000 00000000
WiFi: 3fff31e0:  00000000 3fffc6fc 00000001 3fff22a0
WiFi: 3fff31f0:  00000000 3fffdad

Nuvag

You could use M552 S0/S1 instead of M586, worked for me every time without problems during printing. (probably used 30+ times)

I'm still on 1.21.RC1 and had no wifi problems in the last 2 weeks.
I just installed my PanelDue and added two macros for disabling/enabling wifi, so i can restart it without connecting the usb.

dc42

I'm sorry to hear you are still having problems. Have you confirmed that you are running version 1.21RC4 of both the main firmware and the wifi firmware? Look on the Settings->General page of DWC to check.

You could try downloading and installing DuetWiFiServer 1.21RC4 again, in case the file got corrupted somewhere.

daveidmx

Here's what DWC says I'm running right now:

Firmware Version: 1.21RC4 (2018-03-11 build 1)
WiFi Server Version: 1.21RC4(08b3)
Web Interface Version: 1.21-RC4

I will re-download and re-flash and report back.

daveidmx

Confirmed it still stops responding.

New conn on socket 7 for local port 80
HTTP connection accepted
Found responder
Received 459 bytes
Sending reply, file = no
HTTP req, command words { GET /rr_status HTTP/1.1 }, parameters { type=3 }
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn

dc42

Thanks, that gives me an idea of where to look. Do you use either FTP or Telnet, or just the web interface?

I'll add more debugging in RC5 so that M122 dumps the state of all the connections.

daveidmx

Just the web interface. Do you want me to test something on the others as well? (Or are you just wondering whether something else is also consuming sockets?)

dc42

I was wondering whether FTP or Telnet was consuming sockets.

I've completed version 1.21RC5 of the main firmware, so I'll look at why the wifi firmware might be running out of connections now.

dc42

I have just added DuetWiFiServer.bin version 1.21RC5 to the RRF 1.21RC5 files at https://github.com/dc42/RepRapFirmware/releases/tag/1.21RC5. Please install it on your system. When the problem next occurs, send M111 S1 P14 to enable WiFi debugging (if you haven't already), then send M122. The debug output at the end will include the status of all the connection objects. This should help me determine why none of them is free.

daveidmx

Will do! I'm waiting for a 24-hour print to finish up, so it will be tomorrow.

Any chance you added the remote port numbers to the output? That would help correlate them to a packet trace, and to the client's net state.

ShiftingTech

So, acknowledging that my issue may not be the same one being primarily discussed in this thread, I still think my issue is due some addressing as well. Would you like me to start a separate thread for it, or…?

dc42

If it's different symptoms then a separate thread would be better.

daveidmx

The full M122 output is at the bottom, but I picked out the socket status lines here. (I think there might be a threading bug in the new debug code because the output lines for socket status are interwoven through the entire M122 output.)

WiFi: Conn 0: aborted 80, 56749, 172.20.2.32
WiFi: Conn 1: aborted 80, 57066, 172.20.2.32
WiFi: Conn 2: aborted 80, 56482, 172.20.2.32
WiFi: Conn 3: aborted 80, 57367, 172.20.2.32
WiFi: Conn 4: aborted 80, 58524, 172.20.2.32
WiFi: Conn 5: aborted 80, 58528, 172.20.2.32
WiFi: Conn 6: aborted 80, 58814, 172.20.2.32
WiFi: Conn 7: aborted 80, 58821, 172.20.2.32

FWIW none of those port numbers show up in a netstat.exe dump from the client PC.

M122
=== Diagnostics ===
Used output buffers: 1 of 32 (13 max)
=== Platform ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 1.21RC5 running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DGM-95BNL-MGPSJ-6J1F6-3SS6L-T0XZZ
Static ram used: 16152
Dynamic ram uWiFi: Conn 0: aborted 80, 56749, 172.20.2.32
sed: 100824
Recycled dynamic ram: 1808
Stack ram used: 3576 current, 6512 maximum
Never used ram: 5776
Last reset 05:46:36 ago, cause: power up
Last software reset at 2018-03-15 20:27, reason: User, spinning module GCodes, available RAM 6944 bytes (slot 1)WiFi: Conn 1: aborted 80, 57066, 172.20.2.32

Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0041f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 9
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 372.6ms
MCU temperatureWiFi: Conn 2: aborted 80, 56482, 172.20.2.32
: min 39.5, current 42.9, max 45.5
Supply voltage: min 23.8, current 24.1, max 24.5, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max 0/193
Driver 1: ok, SG min/max 0/1023
Driver 2: standstill, SG min/max not available
DriveWiFi: Conn 3: aborted 80, 57367, 172.20.2.32
r 3: ok, SG min/max 0/1023
Driver 4: standstill, SG min/max not available
Driver 5: standstill, SG min/max 0/216
Driver 6: standstill, SG min/max 0/222
Driver 7: standstill, SG min/max 0/219
Driver 8: standstill, SG min/max 0/205
Driver 9: standstill, SG mWiFi: Conn 4: aborted 80, 58524, 172.20.2.32
in/max not availablWiFi: Conn 5: aborted 80, 58528, 172.20.2.32
e
Expansion motor(s) stall indication: yes
Date/time: 2018-03-17 18:18:45
Slowest main loop (seconds): 0.374137; fastest: 0.000050
=== Move ===
MaxReps: 4, StepErrors: 0, LaErrors: 0, FreeDm: 222, MinFreeDm 150, MaxWait: 5190120ms, UnderWiFi: Conn 6: aborted 80, 58814, 172.20.2.32
runs: 0, 1
Scheduled moves: 833, completed moves: 826
Bed compensation in use: none
Bed probe heights: -0.064 -0.078 -0.086 -0.077 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.4
Heater 1 is on, I-accum = 0WiFi: Conn 7: aborted 80, 58821, 172.20.2.32
.5
=== GCodes ===
Segments left: 1
Stack records: 4 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is doing "G1 X111.412 Y110.526 E0.43514" in state(s) 0
serial is ready with "M122" in state(s) 0WiFi:

aux is idle in state(s) 0
daemWiFi: xmit: 0
on is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
- WiWiFi: recv: 0
Fi -
Network state is running
WiFi module is connected to access poWiFi: fw: 0
int
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21RC5(16b1)
WiFi MAC address 2c:3a:e8:0a:fb:70
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flaWiFi: drop: 0
sh size 4194304, free heap 14712
WiFi IP address 172.20.2.17
WiFi signal strength -53dBm, reconnections 0WiFi: chkerr: 0
, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Expansion ===
DueX I2C errors 0
ok
WiFi: lenerr: 0
WiFi: memerr: 0
WiFi: rterr: 0
WiFi: proterr: 0
WiFi: opterr: 0
WiFi: err: 0
WiFi: cachehit: 0
WiFi:
WiFi: xmit: 12
WiFi: recv: 13
WiFi: fw: 0
WiFi: drop: 2
WiFi: chkerr: 0
WiFi: lenerr: 0
WiFi: memerr: 0
WiFi: rterr: 0
WiFi: proterr: 2