Duet Wifi Webserver not responding

epninety

Will do.

What I did try earlier was to disconnect the lan cable, and reconnect it. The console on the PanelDue updated, showing 'Network running…' and the same, correct ip address.
IP address is configured fixed in config.g as

M540 PBE:EF:DE:AD:FE:EC ; Set MAC address
M552 P192.168.0.236 S1 ; Enable network and set IP address
M553 P255.255.255.0 ; Set netmask
M554 P192.168.0.254 ; Set gateway

and the two printers have different MAC - I just went back to check I'd done that, but they usually aren't powered up at the same time anyway.

epninety

OK, just lost the web interface again…

M552 issued from the PanelDue reports 'Network is enabled, configured IP address: 192.168.0.236, actual IP address: 192.168.0.236'
No response to ping.
No response to M552 S-1
No response to M552 S1
M552 no change in the response. Still no connection to web interface or ping response.

Hooked up a USB connection, fired up minicom... M122 returns the following

=== Diagnostics ===
Used output buffers: 2 of 32 (12 max)
=== Platform ===
RepRapFirmware for Duet Ethernet version 1.20 running on Duet Ethernet 1.0
Board ID: 08DGM-95BNL-MGPSJ-6J1FA-3S06M-91YVW
Static ram used: 11992
Dynamic ram used: 98688
Recycled dynamic ram: 4008
Stack ram used: 3576 current, 8400 maximum
Never used ram: 7984
Last reset 00:22:46 ago, cause: power up
Last software reset at 2018-03-03 12:55, reason: User, spinning module GCodes, available RAM 11880 bytes (slot 0)
Software reset code 0x0003 HFSR 0x00000000, CFSR 0x00000000, ICSR 0x0441f000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 45.6, current 45.9, max 46.0
Supply voltage: min 21.9, current 22.0, max 22.1, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2018-03-03 21:54:20
Cache data hit count 2450058580
Slowest main loop (seconds): 0.003427; fastest: 0.000050
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.3
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
State: 5
HTTP sessions: 1 of 8
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
ok

```Sent M552

Network is enabled, configured IP address: 192.168.0.236, actual IP address: 192.168.0.236
ok

ok

Network is enabled, configured IP address: 192.168.0.236, actual IP address: 192.168.0.236
ok

(Supply voltage looks odd at 22.0V, but it is deliberate and does not indicate a problem)

TickTock

Maybe you can use M583 (Wait for pin) to wait for the release of the external switch before continuing to the M552 S1. I just ran into this issue as well on my first print with the Duet. It was fine for about the first hour and I was able to tweak the extrusion,etc but I was unable connect for the the last couple hours of the print (the print did complete successfully, though). LED on the Wifi module was still steady illuminated but my router indicated that the connection was not present. Pressing reset after the job completed reestablished the the link.

TickTock

Sorry. That was out of context - I just now noticed there was a second page of discussion.

daveidmx

There're multiple different issues being reported on this thread. The one I'm experiencing is where the web gui goes offline but I can still ping the device.

Do you still need more logs for that one?

I'm seeing this on FW 1.21RC3 (2018-02-28 build 4), WiFi server 1.21RC3 (28b1), web interface 1.21-RC4.

I have a few logs I pulled, which I can supply if you need more info. Of note, though, I'm seeing this on the serial console:

[[language]]
HTTP req, command words { GET /rr_status HTTP/1.1 }, parameters { type=3 }
New conn on socket 7 for local port 80
HTTP connection accepted
Found responder
Received 459 bytes
Sending reply, file = no
HTTP req, command words { GET /rr_status HTTP/1.1 }, parameters { type=3 }
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn

An M586 P0 cycle (S0/S1) did not resolve it:

[[language]]
HTTP is disabled
WiFi: recv../src/Listener.cpp(118): stopped listening on port 80
HTTP is enabled on port 80
WiFi: ../src/Listener.cpp(174): listening on port 80
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn

I also have a full network trace. When I refresh the browser, the gist of it is:

[[language]]
--> TCP SYN
<-- TCP SYN ACK
--> TCP ACK
--> HTTP GET
<-- TCP ACK RST
<-- TCP ACK RST

dc42

@daveidmx, thanks for that, the "no free conn" is the source of the problem. Which main and wifi firmware versions are you running? Please try 1.21RC3 + DuetWiFiServer 1.21RC4 if you are not already running those, because they include some relevant fixes.

daveidmx

Thanks! I'm running these:
@daveidmx:

I'm seeing this on FW 1.21RC3 (2018-02-28 build 4), WiFi server 1.21RC3 (28b1), web interface 1.21-RC4.

Is that what you were suggesting to use? Or is there an RC4 of DuetWiFiServer I should test also? I'm looking here:
https://github.com/dc42/RepRapFirmware/tree/dev/EdgeRelease/1.21RC3

dc42

Please try RC4 of DuetWiFiServer, by following this link https://github.com/dc42/DuetWiFiSocketServer/blob/dev/Release/DuetWiFiServer-1.21RC4.bin and then pressing Download.

daveidmx

Got it! I will report back tomorrow.

daveidmx

I didn't get as much testing in today as I'd hoped, but I haven't seen any connection resets so far. Yesterday it was as often as 10 minutes, or as rare as 6 hours. I've had about 2 hours of prints so far today, so… looking good so far?

ShiftingTech

Does the DuetEthernet still use this, or is there something else equivalent that we DuetEthernet folk should be trying out?

dc42

Duet Ethernet doesn't use the DuetWiFiServer.bin file. If you are getting disconnections on the Duet Ethernet and they only happen when you are homing the printer or when printing a file, run M122 after you reconnect and check the MaxReps figure in the report. Note: MaxReps gets reset back to zero after you run M122.

ShiftingTech

I think my disconnects have all been during print processes, but I'm not super confident in that statement. I will look into the maxreps thing. While I'm waiting for another disconnect event, can you explain what the maxreps means? And is any non-zero value bad, or…?

dc42

MaxReps figures above about 50 are bad. The value gives an indication of the interrupt load of the step pulse generator. If it gets too high then the http responder gets starved of CPU time.

ShiftingTech

Got it, thanks.

I just had an ethernet drop out, and when I did an M122 afterwards, I got a maxreps of 4. So I'm guessing that's not my problem…

daveidmx

Sad news on my front. I'm still seeing the web console stop responding on 1.21RC4. Looks like the same issue still. The packet trace shows the same pattern as before (HTTP GET followed immediately by a connection reset) and the console indicates the same message ("refused conn on port 80 no free conn").

I tried to do an [c]M586 P0 S0[/c]/[c]S1[/c] cycle and it looks like it might have crashed the WiFi module. My print froze and I got this on the console:

M586 P0 S0
HTTP is disabled
ok
WiFi:
ESP reported status change
WiFi: Soft WDT reset
ESP reported status change
WiFi:
WiFi: ctx: cont
WiFi: sp: 3fff2fc0 end: 3fff32c0 offset: 01b0
WiFi:
WiFi: >>>stack>>>
WiFi: 3fff3170:  40233576 00000030 0000001c 40225893
WiFi: 3fff3180:  40225d11 3fff6cac 3fff5b3c 40225a2b
WiFi: 3fff3190:  00000003 3fff31d0 00000000 40105f8d
WiFi: 3fff31a0:  00000050 000000ff 00000000 00000000
WiFi: 3fff31b0:  3fff2125 3fff2190 3fff2194 00000000
WiFi: 3fff31c0:  00000000 3fff211c 3fff1900 40106542
WiFi: 3fff31d0:  00000000 005000ff 20000000 00000000
WiFi: 3fff31e0:  00000000 3fffc6fc 00000001 3fff22a0
WiFi: 3fff31f0:  00000000 3fffdad

Nuvag

You could use M552 S0/S1 instead of M586, worked for me every time without problems during printing. (probably used 30+ times)

I'm still on 1.21.RC1 and had no wifi problems in the last 2 weeks.
I just installed my PanelDue and added two macros for disabling/enabling wifi, so i can restart it without connecting the usb.

dc42

I'm sorry to hear you are still having problems. Have you confirmed that you are running version 1.21RC4 of both the main firmware and the wifi firmware? Look on the Settings->General page of DWC to check.

You could try downloading and installing DuetWiFiServer 1.21RC4 again, in case the file got corrupted somewhere.

daveidmx

Here's what DWC says I'm running right now:

Firmware Version: 1.21RC4 (2018-03-11 build 1)
WiFi Server Version: 1.21RC4(08b3)
Web Interface Version: 1.21-RC4

I will re-download and re-flash and report back.

daveidmx

Confirmed it still stops responding.

New conn on socket 7 for local port 80
HTTP connection accepted
Found responder
Received 459 bytes
Sending reply, file = no
HTTP req, command words { GET /rr_status HTTP/1.1 }, parameters { type=3 }
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn
WiFi: ../src/Listener.cpp(62): refused conn on port 80 no free conn