IDEX motor jitter

dc42

@maxgyver it sounds to me that the PID values you are using on the U driver may need to be adjusted. What values are they? In the first instance you could try halving the P and D values to see if that makes the problem go away.

MaxGyver

@dc42

For now, I am using the same values for all closed loop axes:

M569.1 P124.0 T2 C20 R125 I500 D0.1 H100

The problem is also present in open loop mode. I have no issue running the printer with two Y motors on the gantry and a single X-Axis. As soon as I add the U-Axis, the jitter is back. It is most prominent when printing short lines at high speed. I was not able to replicate this behavior outside of a print.

fcwilt

@maxgyver

Could you test running U off of a driver on the 6HC?

Frederick

MaxGyver

@fcwilt said in IDEX motor jitter:

@maxgyver

Could you test running U off of a driver on the 6HC?

Frederick

I just tested this without success. The issue is still present while running U from the main board. But I got the impression that U gets out of sync at the start of each move. On faster moves with high acceleration, it seems to be more severe.

EDIT: Also tested running both Y-Motors from the main board with the same result.

fcwilt

@maxgyver said in IDEX motor jitter:

@fcwilt said in IDEX motor jitter:

@maxgyver

Could you test running U off of a driver on the 6HC?

Frederick

I just tested this without success. The issue is still present while running U from the main board. But I got the impression that U gets out of sync at the start of each move. On faster moves with high acceleration, it seems to be more severe.

EDIT: Also tested running both Y-Motors from the main board with the same result.

What happens if you swap the connections between X and U? The question being is it related to the U axis (firmware problem) or the U hardware.

What sort of speeds are you trying to print at? You mentioned short lines at high speed.

Frederick

MaxGyver

@fcwilt

I am fairly certain that this is a firmware issue, since the problem is also present when U is driven from the main board and the same jittering is present in X when the second extruder (U-axis) is printing and the first extruder (X-axis) is only moving in Y.

Right now, I am printing at 200mm/s with 5000mm/s² accelerations on X, Y and U. Although the jittering is less severe at lower speeds, it is still noticeable.

EDIT:
It is really hard to tell by watching the print. But I got the strong impression that the jitter only courses when the Y-Axis moves! When Y is stationary, the jitter is gone

dc42

@maxgyver do you have any toothed belts running over smooth idlers?

MaxGyver

@dc42 said in IDEX motor jitter:

@maxgyver do you have any toothed belts running over smooth idlers?

Nope. I am a little offended by that.

This is what I have done so far:

checked for loose pulleys
checked belt and belt path
checked if linear rails run smooth
checked motor cables and connectors
checked CAN cable (All from Kenable)
deactivated bed leveling
deactivated demon.g

I have also rewritten most of my config file without success.

fcwilt

@maxgyver said in IDEX motor jitter:

@fcwilt

I am fairly certain that this is a firmware issue, since the problem is also present when U is driven from the main board and the same jittering is present in X when the second extruder (U-axis) is printing and the first extruder (X-axis) is only moving in Y.

Right now, I am printing at 200mm/s with 5000mm/s² accelerations on X, Y and U. Although the jittering is less severe at lower speeds, it is still noticeable.

EDIT:
It is really hard to tell by watching the print. But I got the strong impression that the jitter only courses when the Y-Axis moves! When Y is stationary, the jitter is gone

I see you are using x32 micro-stepping for X, Y and U.

And the speeds you mentioned (200mm/s) are rather fast.

Perhaps the 6HC system cannot keep up?

Could you try x16 micro-stepping at 100mm/s?

I agree it may be the firmware. I am seeking to determine if there is a threshold condition that when crossed the problem appears.

Thanks.

Disclaimer: I am still on firmware 3.3.0 as I am letting others deal with the issues in 3.4.x.

Frederick

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Aug 05 2020 11:42:30 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
M550 P"Factory500"  ; set printer name

; Blower
M950 F0 C"!out4+out4.tach" C"Blower" Q25000 ; create fan 0 on pin out4 and set its frequency
M106 P0 X0.40 B0 H1:2 T80

; Chamer Fan
M950 F4 C"!out5+out5.tach" A"Filter Fan"
M106 P4 X0.30 B0 H0:1:2 T60

; Power ON
M81 C"pson"
M80 ; switch power on
G4 S4 ; wait for expansion boards to boot

; Drives
M569 P0 S0 ; Drive 0.0/Z1 motor (rear left)
M569 P1 S1 ; Drive 0.1/Z2 motor (rear right)
M569 P2 S1 ; Drive 0.2/Z3 motor (front right)
M569 P3 S0 ; Drive 0.3/Z4 motor (front left)
M569 P4 S1 ; Drive 0.4/E1 motor
M569 P5 S0 ; Drive 0.5/E2 motor

; Closed loop drives
M569 P123.0 S0 ; X-Motor
M569 P124.0 S0 ; U-Motor
M569 P125.0 S0 ; Y1-Motor
M569 P126.0 S1 ; Y2-Motor
M569.1 P123.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 123 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.
M569.1 P124.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 124 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.
M569.1 P125.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 125 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.
M569.1 P126.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 126 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.

; Motion System
M584 X123.0 Y125.0:126.0 Z0:1:2:3 U124.0 E4:5 ; set 4 Z drivers and add one U driver -> Must come earlier than M350,M906,M92, M201, M203, M208, M350, M566, M574, M667 and M669
M350 X32 Y32 Z16 U32 E16:16 I1 ; Configure microstepping with interpolation
M92  X160 Y160 Z640 U160 E400:400  ; Set steps per mm
M203 X42000 Y42000 Z1800 U42000 E10000:10000; A40000 B40000 ; Set maximum speeds (mm/min)
M566 X600 Y600 Z200 U600 E600:600 ; set maximum instantaneous speed changes (mm/min)
M201 X30000 Y30000 Z500 U30000 E30000:30000 ;A6000 B6000 ; Set maximum accelerations (mm/s^2)
M906 X2400 Y2400 Z1200 U2400 E900:900 I25 ;A300 B300 ; Set motor currents (mA) and motor idle factor in per cent
M84 S5 ; Set idle timeout
M917 X50 Y50 Z50 U50 ; Set holding current in percent

; Kinematics
M669 K11 Y1:-1:0:-1 ; Matrix mapping for Axis - X:Y:Z:U
;M669 K11 X1:0:0:0 Y1:-1:0:-1 Z0:0:1:0 U0:0:0:1 ; Matrix mapping for Axis - X:Y:Z:U
;M669 K1 X1:0:0:0 Y1:-1:0:-1 Z0:0:1:0 U0:0:0:1

M671 X-41:495.5:495.5:-41 Y353:353:23:23 S10 ; lead screw positions and maximum allowed correction S in mm
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves

; Axis Limits
M208 X0 Y0 Z0 U0 S1 ; set axis minima
M208 X405 Y323 Z350 U405 S0 ; set axis maxima
 
; Endstops
M574 X1 S1 P"123.io1.in" ; configure active-high endstop for low end on X via pin io1.in
M574 Y2 S1 P"126.io1.in" ; configure active-high endstop for low end on Y via pin io1.in
M574 U2 S1 P"124.io1.in" ; configure active-high endstop for high end on U via pin io1.in
M574 Z2 S1 P"io3.in" ; configure active-high endstop for high end on Z via pin io0.in

; Z-Probe
M558 P5 C"io5.in" H2 A10 S0.01 R0 F300:150 T60000       ; IR Z-Probe 1: set Z probe type and the dive height + speeds
M376 H10                                                ; Set height (mm) over which to taper off the bed compensation (should be 20x max mesh error)
G31 P500 X0 Y20 Z1.5                                    ; Set Z probe parameters, lower Z-value -> nozzle further down
                                        
; Bed Heater
M308 S0 P"temp0" A"Bed" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M950 H0 C"out8" Q10 T0 ; create bed heater output on bed output and map it to sensor 0
M143 H0 S125 ; set temperature limit for heater 0 to 120C
M307 H0 R0.383 K0.269:0.000 D2.81 E1.35 S1.00 B0 ; enable PWM mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0

; Hotend1 Heater
M308 S1 P"temp1" A"Extruder1" Y"pt1000" R2200 ; configure sensor 1 as PT1000 on pin temp1
M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
M143 H1 S300 ; set temperature limit for heater 1 to 280C
M307 H1 R2.872 K0.252:0.115 D1.45 E1.35 S1.00 B0 V23.8

; Hotend2 Heater
M308 S2 P"temp2" A"Extruder2" Y"pt1000" R2200 ; configure sensor 2 as PT1000 on pin temp2
M950 H2 C"out2" T2 ; create nozzle heater output on out2 and map it to sensor 2
M143 H2 S300 ; set temperature limit for heater 2 to 280C
M307 H2 R2.872 K0.252:0.115 D1.45 E1.35 S1.00 B0 V23.8 ; disable bang-bang mode for heater and set PWM limit

; Tools
; tool 0, X-axis
M563 P0 D0 H1 X0 F1 ; tool 0 uses extruder1 and heater 1 with fan 1 as the print cooling fan
M568 P0 R0 S0 ; set standby and active temperatures for tool 0
G10 P0 X0 Y0 Z0 S0 R0 ; set tool 0 offsets and temperatures
M950 F1 C"out6" ; T0 Fan

; tool 1, U-axis 
M563 P1 D1 H2 X3 F2 ; tool 1 uses extruder2 and heater 2 with fan 2 as the print cooling fan and maps X to U
M568 P1 R0 S0 ; set standby and active temperatures for tool 1
G10 P1 X0 U1.6 Y0 Z0 S0 R0 ; set tool 1 offsets and temperatures. (increase U to move nozzle to the left)
M950 F2 C"out7" ; T1 Fan

; Create a tool that prints 2 copies of the object using both carriages'''
;M563 P2 D0:1 H1:2 X0:3 F1:2 S"Duplication Mode" ; tool 2 uses both extruders, hot end heaters and fans, and maps X to both X and U
;G10 P2 X0 Y0 U-205 S0 R0 ; set tool offsets and temperatures
;M567 P2 E1:1 ; set mix ratio 100% on both extruders

; Create a tool that prints 2 mirrored copies of the object using both carriages'''
;M563 P3 D0:1 H1:2 X0:3 F1:2 S"Mirror Mode" ;tool 3 uses both extruders, hot end heaters and fans, and maps X to both X and U
;G10 P3 X0 Y0 U-465 S0 R0 ; set tool offsets and temperatures
;M567 P3 E1:1 ; set mix ratio 100% on both extruders

; Temp sensors
M308 S7 Y"mcu-temp" A"MCU" ; configure sensor 5 as thermistor for MCU
M308 S3 P"124.temp0" Y"pt1000" R2180     A"Chamber Temp." ; Setup temp  0  on 1HCL at CAN address 50 as sensor 3  - sensing the chamber temperature
M308 S4 P"temp3" A"Blower Temp." Y"thermistor" T100000 B3950 ; define bed temperature sensor
 ; LED lights
M950 P3 C"out3"
M42 P3 S1

; Pressure Advance
M572 D0:1 S0.02 ; Extruder Drive Number, Pressure advance amount

; Accelerometer
;M955 P0 C"io4.out+io4.in" I05

; input shaping
;M593 P"none" F99
M501 ; set the active parameters to those stored in sys/config-override.g

M291 P"The printer is not homed, home now?" R"Homing" S3
 G28```

dc42

@maxgyver if the vibration occurs when both U and Y motors are driven from the main board, then I don't see how it can be a firmware issue, because in that configuration I can't see any way that the steps would get out of sync.

martin7404

I had the same isue with duet wifi and duex5- double makfoged IDEx machine. In the end it was fualty driver on wifi board. New duet wifi solved the isue

fcwilt

@martin7404 said in IDEX motor jitter:

I had the same isue with duet wifi and duex5- double makfoged IDEx machine. In the end it was fualty driver on wifi board. New duet wifi solved the isue

Since he was tried different drivers on the 6HC and on the three 1HCLs do you think a driver problem is likely?

Thanks.

Frederick

MaxGyver

@dc42 said in IDEX motor jitter:

@maxgyver if the vibration occurs when both U and Y motors are driven from the main board, then I don't see how it can be a firmware issue, because in that configuration I can't see any way that the steps would get out of sync.

The vibrations are still present when both U and Y motors are driven from the main board.

@fcwilt x16 microstepping makes no difference

What would be the theoretical maximum achievable speed for a system with dual mark forged belts?
I am interested in the math behind this.

I am using GT2 belts with 20teeth pulleys.

MaxGyver

@dc42

I managed to get a slow motion shot of the U axis jitter. This was captured with U and Y driven from the main board.

Video

fcwilt

@maxgyver said in IDEX motor jitter:

@dc42

I managed to get a slow motion shot of the U axis jitter. This was captured with U and Y driven from the main board.

Video

You are referring to the left/right motion?

Yes, quite obvious.

And if you connect the X driver to the U axis hardware and the U driver to the X axis hardware the problem moves to the X axis hardware?

Frederick

MaxGyver

@fcwilt said in IDEX motor jitter:

And if you connect the X driver to the U axis hardware and the U driver to the X axis hardware the problem moves to the X axis hardware?

I can test this tomorrow, but when I print with the secondary extruder on the U axis, the same left/right motion is present in X. So I suppose it is not a problem with the U axis hardware.

dc42

@maxgyver do X, Y and U axes have the same steps/mm?

MaxGyver

@dc42 said in IDEX motor jitter:

@maxgyver do X, Y and U axes have the same steps/mm?

Yes.
I did also test different microstepping settings with no improvement.

; Drives
M569 P0 S0 ; Drive 0.0/Z1 motor (rear left)
M569 P1 S1 ; Drive 0.1/Z2 motor (rear right)
M569 P2 S1 ; Drive 0.2/Z3 motor (front right)
M569 P3 S0 ; Drive 0.3/Z4 motor (front left)
M569 P4 S1 ; Drive 0.4/E1 motor
M569 P5 S0 ; Drive 0.5/E2 motor

; Closed loop drives
M569 P123.0 S0 ; X-Motor
M569 P124.0 S0 ; U-Motor
M569 P125.0 S0 ; Y1-Motor
M569 P126.0 S1 ; Y2-Motor
M569.1 P123.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 123 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.
M569.1 P124.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 124 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.
M569.1 P125.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 125 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.
M569.1 P126.0 T2 C20 R125 I500 D0.1 H50 ; Configure the 1HCL board at CAN address 126 with a quadrature encoder on the motor shaft that has 20 steps per motor full step.

; Motion System
M584 X123.0 Y125.0:126.0 Z0:1:2:3 U124.0 E4:5 ; set 4 Z drivers and add one U driver -> Must come earlier than M350,M906,M92, M201, M203, M208, M350, M566, M574, M667 and M669
M350 X32 Y32 Z16 U32 E16:16 I1 ; Configure microstepping with interpolation
M92  X160 Y160 Z640 U160 E400:400  ; Set steps per mm
M203 X42000 Y42000 Z1800 U42000 E10000:10000; A40000 B40000 ; Set maximum speeds (mm/min)
M566 X600 Y600 Z200 U600 E600:600 ; set maximum instantaneous speed changes (mm/min)
M201 X30000 Y30000 Z500 U30000 E30000:30000 ;A6000 B6000 ; Set maximum accelerations (mm/s^2)
M906 X2400 Y2400 Z1200 U2400 E900:900 I25 ;A300 B300 ; Set motor currents (mA) and motor idle factor in per cent
M84 S5 ; Set idle timeout
M917 X50 Y50 Z50 U50 ; Set holding current in percent

; Kinematics
M669 K11 Y1:-1:0:-1	; Matrix mapping for Axis - X:Y:Z:U
;M669 K11 X1:0:0:0 Y1:-1:0:-1 Z0:0:1:0 U0:0:0:1	; Matrix mapping for Axis - X:Y:Z:U
;M669 K1 X1:0:0:0 Y1:-1:0:-1 Z0:0:1:0 U0:0:0:1

M671 X-41:495.5:495.5:-41 Y353:353:23:23 S10 ; lead screw positions and maximum allowed correction S in mm
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves

; Axis Limits
M208 X0 Y0 Z0 U0 S1 ; set axis minima
M208 X405 Y323 Z350 U405 S0 ; set axis maxima

dc42

@maxgyver if the axes have identical steps/mm and microstepping, then the step pulses should be precisely synchronised. So I think it must be a mechanical problem.

Is there any vibration when you move each of the 3 motors individually? You can use G91 followed by G1 H2 commands to test that.

martin7404

@dc42 In double makfoged he can move individually X and U but for Y he moves all the motors