Temperature setting gone.
-
Hello everyone,
the display of the temperature setting disappeared from the display panel on my computer.
do you have an idea.
Thank you. -
Can you show a photo of what you mean?
Have you recently changed anything? Firmware update? Does your DWC version match your firmware version?
-
@phaedrux Here is a picture. Yes I made an update recently.
-
no one can help me. I just made an update, before it worked very well. I attach my config file.
; Configuration file for Duet WiFi (firmware version 1.21) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2 on Sun Mar 17 2019 11:25:52 GMT+0100 (heure normale d’Europe centrale) ; ---------------------------------------------------------------------------------------------------------------------------------------------- ; General preferences ; ---------------------------------------------------------------------------------------------------------------------------------------------- G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M665 R160.00 L400.00 H520.00 B140.00 ;M665 R160 L400 B150 H520; Set delta radius, diagonal rod length, printable radius and homed height H500 M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Network ; ----------------------------------------------------------------------------------------------------------------------------------------------- M550 P"LittleMonsterWifi" ; Set machine name M552 S1 ; Enable network ;M587 S"Livebox-2AF2" P"........................." ; Configure access point. You can delete this line once connected M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Drives ; ----------------------------------------------------------------------------------------------------------------------------------------------- M569 P0 S1 ; Drive 0 goes forwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S1 ; Drive 3 goes forwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation M92 X80.00 Y80.00 Z80.00 E427.190 ; Set steps per mm M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; Set maximum instantaneous speed changes (mm/min) M203 X19980.00 Y19980.00 Z19980.00 E3600.00 ; Set maximum speeds (mm/min) M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; Set accelerations (mm/s^2) M906 X1000.00 Y1000.00 Z1000.00 E800.00 I60 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Axis Limits ; ----------------------------------------------------------------------------------------------------------------------------------------------- M208 Z0 S1 ; Set minimum Z ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Endstops ; ----------------------------------------------------------------------------------------------------------------------------------------------- M574 X2 S1 P"xstop" ; ok Set active high endstops M574 Y2 S1 P"ystop" ; ok Set active high endstopS M574 Z2 S1 P"zstop" ; ok Set active high endstops ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Z-Probe ; ----------------------------------------------------------------------------------------------------------------------------------------------- M558 P9 C"^zprobe.in+zprobe.mod" H5 F300 T3000 ; Set Z probe type to bltouch and the dive height + speeds H10 M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch G31 P500 X0 Y25 Z0.00 ; Set Z probe trigger value, offset and trigger height 2.45; 2.658 M557 R140 S25 ; Define mesh grid ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Heaters ; ----------------------------------------------------------------------------------------------------------------------------------------------- M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 R4700 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M140 H0 P0 ; resets the temperature limit for the heater to the default for bed heaters M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.060000e-8 R4700 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C ;M307 H1 A437.1 C302.4 D0.6 S1.00 V24.3 B0 ; PID tuning ed3 v6 buse 0,4 ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Fans ; ----------------------------------------------------------------------------------------------------------------------------------------------- M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency FAN IMPRESSION M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency FAN BUSE M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency FAN BOITIER MCU ;M106 P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off M106 P2 F100 L0.4 B0.5 T33:40 H100:101:102 ; Set fan 2 Duet case fan. Turns on when the MCU temperature (virtual heater 100) ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; ----------------------------------------------------------------------------------------------------------------------------------------------- ; Tools ; ----------------------------------------------------------------------------------------------------------------------------------------------- M563 P0 D0 H1 ; Define tool 0 G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures ;*** If you have a single-nozzle build, comment the next 2 lines M563 P1 D1 H2 ; Define tool 1 G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures M579 X0.996 Y0.993 Z1.00 ; scaling factor for Cartesian cords x1.01266 Y1.00908 X0.99453 ; ------------------------------------------------------------------------------------------------------------------------------------------------ ; ------------------------------------------------------------------------------------------------------------------------------------------------ ; Automatic saving after power loss is not enabled ; ------------------------------------------------------------------------------------------------------------------------------------------------ ; ------------------------------------------------------------------------------------------------------------------------------------------------ ; Custom settings are not configured M575 P1 B57600 S1; panel due ; ------------------------------------------------------------------------------------------------------------------------------------------------ ; ------------------------------------------------------------------------------------------------------------------------------------------------ ; Miscellaneous ; ------------------------------------------------------------------------------------------------------------------------------------------------ G29 S1 M501 ; Load saved parameters from non-volatile memory ; ------------------------------------------------------------------------------------------------------------------------------------------------ -
How many tools do you actually have?
Your config shows two tools being defined, but there is no heater or extruder defined for the second tool.
;*** If you have a single-nozzle build, comment the next 2 lines M563 P1 D1 H2 ; Define tool 1 G10 P1 S0 R0 ; Set tool 1 operating and standby temperaturesI think those lines should be commented out.
G29 S1G29 S1 should not be used in config.g. Load the heightmap in your slicer start gcode after homing the z axis.
Can you please send M122 and M98 P"config.g" and post the results?
-
I have an extruder and heater EV6
here is the M122
08/02/2022, 19:08:54 M122 === Diagnostics === RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later Board ID: 08DDM-9FAM2-LW4SD-6J9FL-3SJ6J-KJZ7Y Used output buffers: 3 of 24 (12 max) === RTOS === Static ram: 23876 Dynamic ram: 74368 of which 68 recycled Never used RAM 16104, free system stack 134 words Tasks: NETWORK(ready,13.0%,237) HEAT(delaying,0.0%,330) Move(notifyWait,0.1%,305) MAIN(running,86.2%,503) IDLE(ready,0.7%,29), total 100.0% Owned mutexes: WiFi(NETWORK) === Platform === Last reset 00:02:18 ago, cause: power up Last software reset at 2022-02-06 20:59, reason: User, GCodes spinning, available RAM 16104, slot 2 Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a Error status: 0x00 Aux0 errors 0,0,0 Step timer max interval 0 MCU temperature: min 14.1, current 22.3, max 22.6 Supply voltage: min 24.2, current 24.4, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0 Driver 0: position 70738, standstill, SG min/max 0/118 Driver 1: position 70738, standstill, SG min/max 0/130 Driver 2: position 70738, standstill, SG min/max 0/143 Driver 3: position 0, standstill, SG min/max not available Driver 4: position 0, standstill, SG min/max not available Driver 5: position 0 Driver 6: position 0 Driver 7: position 0 Driver 8: position 0 Driver 9: position 0 Driver 10: position 0 Driver 11: position 0 Date/time: 2022-02-08 19:08:53 Cache data hit count 4294967295 Slowest loop: 11.14ms; fastest: 0.16ms I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0 === Storage === Free file entries: 10 SD card 0 detected, interface speed: 20.0MBytes/sec SD card longest read time 3.3ms, write time 0.0ms, max retries 0 === Move === DMs created 83, maxWait 106475ms, bed compensation in use: mesh, comp offset 0.000 === MainDDARing === Scheduled moves 5, completed moves 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP is idle in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 Daemon is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === Network === Slowest loop: 15.66ms; fastest: 0.00ms Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions HTTP sessions: 1 of 8 - WiFi - Network state is active WiFi module is connected to access point Failed messages: pending 0, notready 0, noresp 0 WiFi firmware version 1.26 WiFi MAC address 5c:cf:7f:ee:6a:e7 WiFi Vcc 3.40, reset reason Turned on by main processor WiFi flash size 4194304, free heap 25512 WiFi IP address 192.168.1.18 WiFi signal strength -66dBm, mode 802.11n, reconnections 0, sleep mode modem Clock register 00002002 Socket states: 0 0 0 0 0 0 0 0M98 P"config.g"
08/02/2022, 19:10:10 M98 P"config.g" HTTP is enabled on port 80 FTP is disabled TELNET is disabled Error: in file macro line 34 column 19: M350: array too long, max length = 0 Error: in file macro line 35 column 27: M92: array too long, max length = 0 Error: in file macro line 36 column 34: M566: array too long, max length = 0 Error: in file macro line 37 column 37: M203: array too long, max length = 0 Error: in file macro line 38 column 34: M201: array too long, max length = 0 Error: in file macro line 39 column 34: M906: array too long, max length = 0 Error: Sensor number out of range Error: bad drive number Error: Tool 0 not found Error: bad drive number Error: Tool 1 not found Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset. Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 277Cthank you for your help
-
Hello, no one can help me
-
@synergy41 it looks like you haven't assigned any driver to the extruder. If your extruder is connected to the E0 motor output, add this before line 34:
M584 X0 Y1 Z2 E3
Duet WiFi hardware designer and firmware engineer
Please do not ask me for Duet support via PM or email, use the forum
http://www.escher3d.com, https://miscsolutions.wordpress.com -
@dc42
Thank you, that was right.
It's passing something weird then during the update to 3.3 -
I think the problem was that your old config didn't have an M584 command and there were defaults in older firmware. There a no longer defaults and the M584 command must be present.
-
undefined dc42 marked this topic as a question
-
undefined dc42 has marked this topic as solved
