@phaedrux
I have an extruder and heater EV6
here is the M122
08/02/2022, 19:08:54 M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3 (2021-06-15 21:44:54) running on Duet WiFi 1.02 or later
Board ID: 08DDM-9FAM2-LW4SD-6J9FL-3SJ6J-KJZ7Y
Used output buffers: 3 of 24 (12 max)
=== RTOS ===
Static ram: 23876
Dynamic ram: 74368 of which 68 recycled
Never used RAM 16104, free system stack 134 words
Tasks: NETWORK(ready,13.0%,237) HEAT(delaying,0.0%,330) Move(notifyWait,0.1%,305) MAIN(running,86.2%,503) IDLE(ready,0.7%,29), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:02:18 ago, cause: power up
Last software reset at 2022-02-06 20:59, reason: User, GCodes spinning, available RAM 16104, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 14.1, current 22.3, max 22.6
Supply voltage: min 24.2, current 24.4, max 24.7, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 70738, standstill, SG min/max 0/118
Driver 1: position 70738, standstill, SG min/max 0/130
Driver 2: position 70738, standstill, SG min/max 0/143
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2022-02-08 19:08:53
Cache data hit count 4294967295
Slowest loop: 11.14ms; fastest: 0.16ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 106475ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5, completed moves 5, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 15.66ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address 5c:cf:7f:ee:6a:e7
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 25512
WiFi IP address 192.168.1.18
WiFi signal strength -66dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
M98 P"config.g"
08/02/2022, 19:10:10 M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: in file macro line 34 column 19: M350: array too long, max length = 0
Error: in file macro line 35 column 27: M92: array too long, max length = 0
Error: in file macro line 36 column 34: M566: array too long, max length = 0
Error: in file macro line 37 column 37: M203: array too long, max length = 0
Error: in file macro line 38 column 34: M201: array too long, max length = 0
Error: in file macro line 39 column 34: M906: array too long, max length = 0
Error: Sensor number out of range
Error: bad drive number
Error: Tool 0 not found
Error: bad drive number
Error: Tool 1 not found
Warning: the height map was loaded when the current Z=0 datum was not determined probing. This may result in a height offset.
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 277C
thank you for your help