BL Touch Installation what is Servo Pin?
-
Should it look like this?
-
@signpostman said in BL Touch Installation what is Servo Pin?:
@fcwilt I have tried CAT 5 cable and now I have 18 gauge 4 conductor that is not twisted pair
I would remove one twisted pair from the CAT cable and use that. And I would make sure to route it away from any source of noise, like stepper wiring.
Frederick
Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6
-
-
Adding ^ didn't seem to help
-
@signpostman said in BL Touch Installation what is Servo Pin?:
Adding ^ didn't seem to help
And you re-booted after making the change?
It was worth a try.
Frederick
-
@signpostman said in BL Touch Installation what is Servo Pin?:
Should it look like this?
On the Duet3 the pullup should not be enabled.
-
@phaedrux said in BL Touch Installation what is Servo Pin?:
@signpostman said in BL Touch Installation what is Servo Pin?:
Should it look like this?
On the Duet3 the pullup should not be enabled.
True but at this point any change might help point to the problem.
Frederick
Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6
-
@fcwilt said in BL Touch Installation what is Servo Pin?:
@signpostman said in BL Touch Installation what is Servo Pin?:
@fcwilt I have tried CAT 5 cable and now I have 18 gauge 4 conductor that is not twisted pair
I would remove one twisted pair from the CAT cable and use that. And I would make sure to route it away from any source of noise, like stepper wiring.
Frederick
This might be your best bet. Short of a toolboard.
As a sanity check can you test the bltouch with a much shorter length of wire with the probe not mounted on the print head? Keep it vertical and trigger it by hand to see if it will stop the Z axis.
-
@fcwilt Agree
-
@phaedrux What other probe do you suggest that would work with a long cable?
-
Maybe a good quality Normally Closed microswitch that you could manually mount before probing with some good quality shielded wire? Or a conductive touch plate that could be moved under the nozzle?
With a printer that size options may be limited?
With better wire the BLTouch may be viable as well.
-
@signpostman said in BL Touch Installation what is Servo Pin?:
@phaedrux What other probe do you suggest that would work with a long cable?
What sort of bed do you have? What is it made of. What sort of surface do you print on?
Thanks.
Frederick
-
@fcwilt Right now I have a piece of corrugated plastic, so the probe does not get destroyed. I am going to have a aluminum with steel overlay when complete.
-
@signpostman said in BL Touch Installation what is Servo Pin?:
@fcwilt Right now I have a piece of corrugated plastic, so the probe does not get destroyed. I am going to have a aluminum with steel overlay when complete.
Will there be any magnets involved like you find in the Buildtak system?
Thanks.
Frederick
-
@phaedrux I just shortened the cables and put new fittings on the end
-
Still have exactly same issue.
-
@signpostman said in BL Touch Installation what is Servo Pin?:
Still have exactly same issue.
Do you have all 5 wires from the BLTouch connected to the board?
Thanks.
Frederick
-
Yes Black and Brown connected to the same pin
-
I might be crazy but I ordered a new BL Touch, see if it acts the same?
-
@signpostman said in BL Touch Installation what is Servo Pin?:
I might be crazy but I ordered a new BL Touch, see if it acts the same?
It's possible that you have a defective one.
It's also possible that the existing one needs adjustment. I've never had to do it but I understand there is some sort of adjustment that sometimes needs to be made.
Frederick
