Error following update

synergy41

Good evening,
Following my many problems of setting, I wanted to make the update in 1.19,
But as a misfortune never happens alone I made a mistake, I downloaded the .bin from the web interface and instead of refusing the installation I accept ,,,
So my DUET WIFI does not want to connect on my wifi, I have good hand via PONTERFACE, but impossible to start the wifi via command M552 S1,
I run M122 this is what it shows me.
–----------------------------------------------------------------
**>>> M552 S0
SENDING:M552 S0
WiFi module started
Error: Failed to initialise WiFi module, code -10
[ERROR] Error: Failed to initialise WiFi module, code -10

M552 S1
SENDING:M552 S1
WiFi module started
Error: Failed to initialise WiFi module, code -10
[ERROR] Error: Failed to initialise WiFi module, code -10

M122
SENDING:M122
=== Diagnostics ===
Used output buffers: 1 of 32 (14 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.19beta11 running on Duet WiFi 1.0
Board ID: 08DDM-9FAM2-LW4SD-6J9FL-3SJ6J-KJZ7Y
Static ram used: 21132
Dynamic ram used: 96292
Recycled dynamic ram: 1360
Stack ram used: 4008 current, 5316 maximum
Never used ram: 6972
Last reset 00:03:25 ago, cause: power up
Last software reset reason: User, spinning module GCodes, available RAM 6972 bytes (slot 0)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
[ERROR] Error status: 0

Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms
MCU temperature: min 30.7, current 31.8, max 32.6
Supply voltage: min 0.4, current 0.5, max 0.6, under voltage events: 0, over voltage events: 0
Driver 0: ok
Driver 1: ok
Driver 2: ok
Driver 3: ok
Driver 4: ok
Date/time: 1970-01-01 00:00:00
Slowest main loop (seconds): 0.100082; fastest: 0.000031
=== Move ===
MaxReps: 0, StepErrors: 0, FreeDm: 240, MinFreeDm 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is ready with "M122" in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is disabled
WiFi module is disabled
HTTP sessions: 0 of 8
Socket states: 0 0 0 0 0 0 0 0
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)**
–---------------------------------------------
If someone has an idea.
thanks in advance

dc42

Put the SD card in a PC, copy DuetWiFiServer-1.19.bin into it and rename it to exactly DuetWiFiServer.bin. Safely remove the card from the PC, put it back in the Duet. Restart the Duet and run M997 S1 to install it. When the blue led on the WiFi module stops flashing, run your macro to set the access point details.

synergy41

He replies that:
SENDING: M997 S1
File DuetWiFiServer.bin not found

dc42

I should have said you need to put that file in the /sys folder on the card.

synergy41

Yes it is well here that I put the file

dc42

Did you either restart the Duet or send M21 after you put the SD card back in?

Are you sure its name matches exactly the name it says it can't find?

synergy41

No I did not restart or made M21, must I do it.
Yes the filename is the same. Can we do a hard reset on this card?
Thank you for your patient

dc42

You can do a hard reset by pressing the reset button (don't press the erase button by mistake!). Or you can send M999.

Stigern

Hi, I also upgraded my firmware, then ran into issues regarding the wifi module. So I DL the DuetWiFiServer-1.19.bin file and renamed it to DuetWiFiServer.bin

It wrote the firmware successfull but still I'm not able to start wifi module. Here is a log from pronterface. I have also tried restarting the duet wifi after firmware upgrade.

Connecting...
Printer is now online.
>>> M997 S1
SENDING:M997 S1
Trying to connect at 460800 baud:
 success
Erasing 290848 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful
WiFi module started
Error: Failed to initialise WiFi module, code -10
[ERROR] Error: Failed to initialise WiFi module, code -10

>>> M552 S1
SENDING:M552 S1
WiFi module started
Error: Failed to initialise WiFi module, code -10
[ERROR] Error: Failed to initialise WiFi module, code -10

EDIT:

Hm, seems like it didnt upgrade the wifi firmware, shouldn't it be 1.19?

M115
SENDING:M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.19 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2017-08-14

Running the firmware upgrade routine again won't change from 1.0 to 1.19 wifi firmware.

EDIT! For anyone else just seeing this post, read this page: https://duet3d.com/wiki/Upgrading_to_DuetWiFiFirmware_1.19

Solved all my issues! Do EXACTLY as it says.

synergy41

HELLO,
It shows me this message is normal?

SENDING: M999
[ERROR] Can not read from printer (disconnected?) (SerialException): call to ClearCommError failed
Exception in thread Thread-15:
Traceback (most recent call last):
File "threading.pyc", line 808, in __bootstrap_inner
File "threading.pyc", line 761, in run
File "printrun \ printcore.pyc", line 357, in _sender
File "printrun \ printcore.pyc", line 623, in _send
File "encodings \ utf_8.pyc", line 16, in decode
UnicodeDecodeError: 'utf8' codec can not decode byte 0xe9 in position 33: invalid continuation byte

synergy41

Well I move slowly,
Now I just have a problem with the SetNetwork macro when I get to this step: M587 S "your-network-ssid" P "your-network-password". I therefore replace the non of my network between the "….." and the password of it between the "....." which gives the code:
M587 S "...." P "...."
I make the command and I have the error:
Unsupported command: M857 S "...." P "....."
Is something wrong?
Thank you

Dougal1957

you seem to have a typo make sure the command you are sending is indeed M587 your error looks like you are send M857?

synergy41

Thank you
yes that's right, but it's been 3 days that I try to advance with this printer so I'm starting to be tired.
The map to find my network wifi:
>>> M587
SENDING: M587
Remembered networks:
LIVEBOX-2AF2

But if I want to connect to it with the command M552 S1 it returns the following error message:

M552 S1
SENDING: M552 S1
WiFi reported error: no known networks found
Wifi module is idle

–-------------------------------------------------------

When I reconnect on PONTERFACE I have this message: Connecting ...
Printer is now online.
WiFi reported error: no known networks found
Wifi module is idle

Do you have an idea ?
Thank yo

dc42

It probably means that you didn't send the M587 command to store the SSID and password details correctly. You can send M587 with no parameters to get a list of SSIDS that have been stored.

Instead of send the M587 command from a macro, you can also use a terminal emulator. Under Windows I use YAT, https://sourceforge.net/projects/y-a-terminal/. You can't use Pronterface, Repetier etc. because they will convert the lower case characters in your password to uppercase.

synergy41

@dc42:

It probably means that you didn't send the M587 command to store the SSID and password details correctly. You can send M587 with no parameters to get a list of SSIDS that have been stored.

Instead of send the M587 command from a macro, you can also use a terminal emulator. Under Windows I use YAT, https://sourceforge.net/projects/y-a-terminal/. You can't use Pronterface, Repetier etc. because they will convert the lower case characters in your password to uppercase.

Thanks to all, it's back again.
Thank you for your patient.
It is necessary to use YAT

Error following update

When I reconnect on PONTERFACE I have this message: Connecting ... Printer is now online. WiFi reported error: no known networks found Wifi module is idle

When I reconnect on PONTERFACE I have this message: Connecting ...
Printer is now online.
WiFi reported error: no known networks found
Wifi module is idle