help for beginners
-
@sergei
please post the untranslated version -
an untranslated version of the M 122 command?
-
@sergei
yes -
М122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.05.1 running on Duet Ethernet 1.02 or later
Board ID: 08DLM-996RU-N8PS0-6J9FG-3S86R-9BSMN
Used output buffers: 1 of 24 (8 max)
=== RTOS ===
Static ram: 25712
Dynamic ram: 93104 of which 76 recycled
Exception stack ram used: 320
Never used ram: 11860
Tasks: NETWORK(ready,792) HEAT(blocked,1232) MAIN(running,3736) IDLE(ready,160)
Owned mutexes:
=== Platform ===
Last reset 00:07:07 ago, cause: software
Last software reset at 2021-01-21 10:02, reason: User, spinning module GCodes, available RAM 11656 bytes (slot 3)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 36.6, current 36.9, max 37.4
Supply voltage: min 11.0, current 11.4, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2021-01-21 10:09:25
Cache data hit count 875887931
Slowest loop: 3.27ms; fastest: 0.07ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Move ===
Hiccups: 0, FreeDm: 160, MinFreeDm: 160, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== DDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
Heater 0 is on, I-accum = 0.0
Heater 2 is on, I-accum = 0.4
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 13.32ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state 5, link 100Mbps full duple -
can you help with this problem?
-
post a sliced g code where the speed drops
-
it falls right after the start of printing
-
@sergei said in help for beginners:
it falls right after the start of printing
did you set your slicer to reprap instead of marlin?
-
Yes of course
-
-
here is the complete code
-
-
@Phaedrux said in help for beginners:
A description of your printer? What hardware? Photos?
Are you using a mixing extruder? Or two independant extruders?
It looks like you're using cura to slice? What version of cura are you using?
-
extruders I have independent separately from each other. Cura version 15.04.3
-
That's a pretty ancient version of Cura at this point. They have wrapped around to 0 again and are already back up to 4.8.
https://ultimaker.com/learn/ultimaker-cura-4-8-is-here
Might be time to look into updating your firmware too. 2.05 is over a year old now. RRF3.2 is out.
If you still have access to DWC. Upload these 3 zip files, one at a time. Don't extract them. Reboot after each.
https://github.com/Duet3D/RepRapFirmware/releases/download/2.05.1/Duet2Firmware-2.05.1.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.0/Duet2and3Firmware-3.0.zip
https://github.com/Duet3D/RepRapFirmware/releases/download/3.2/Duet2and3Firmware-3.2.zip
That will get your firmware and DWC up to date.For your config, might be a good idea to run through the configurator tool and generate a fresh set for RRF3.
https://configtool.reprapfirmware.org/Start -
how else to understand how to do it all. unfortunately I don't understand much yet
-
in my config.json you can help me write a firmware for two chimera extruders. the distance between the nozzles is 18 mm. otherwise the dimensions of the working area of the limit switches
-
You've already setup you tools in config.g
; Tools M563 P0 D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C M563 P1 D1 H2 F0 ; define tool 1 G10 P1 X-18 Y0 Z0 ; set tool 1 axis offsets G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0CIs tool1 18mm to the left of tool0?
-
tell me how to connect and where to register the filament end sensor
-
