Major delta problems

DocTrucker

I'm just throwing ideas in here and have no experience of deltas!

I'd check over the heater cartridge and temperature sensor connectors to double check the heating isn't dropping out or spiking. Temp plot look normal? Another temp sensor available to test as a trial (while hoping it doesn't knock calibration out too far)?

dc42

To me, it looks like over extrusion or possibly poor adhesion to the bed.

garyd9

Some more information:

This issue isn't limited to the first layer. In fact, it's more pronounced as the layer counts grow.

The patterns appear random, but repeats across layers and prints. Any time I print a single layer disk with 45 degree lines, it'll look very similar to the one I posted earlier. The same happens for the 135 degree lines.

mhackney

Gary, it wouldn't hurt to do an extruder calibration test. And the reason I asked about silicone lubricants on face book was to eliminate a bed adhesion issue.

David and all, Gary's issues started with an odd mechanical issue (binding on one of the carriages) which he has mostly but completely resolved. I suggested printing 1 layer to see what effect that would have on the print as he was seeing smaller more localized top layer artifacts on larger parts. Rather than print a thick part, one can collect a lot of good data quickly on a single layer print. That's what led to this "discovery".

The printer is an Ultibots D300VS+ modified to use the piezo rather than the stock FSRs. I wrote the assembly guide for this printer and it is an easily built machine that calibrates well. The bed is PEI and at 65°C, PLA should stick like glue (if it is not contaminated and clean).

Cheers,
Michael

garyd9

@dc42 said in Major delta problems:

To me, it looks like over extrusion or possibly poor adhesion to the bed.

Checked the extrusion. 100mm for 100mm (+/- some fraction of a mm) over 3 tries. I changed filament, same issue. Bed adhesion is good based on the experience removing the prints. (PEI well cleaned with alcohol or acetone. I've also repeated the issue on glass with purple glue stick.)

@doctrucker said in Major delta problems:

I'd check over the heater cartridge and temperature sensor connectors to double check the heating isn't dropping out or spiking. Temp plot look normal? Another temp sensor available to test as a trial (while hoping it doesn't knock calibration out too far)?

Temp plot is smooth.

Something I think being missed is that this "pattern" is fairly consistent. If I print the same gcode file 3 times, all three prints have the same "ripples" in mostly the same area. (They might shift a mm or two, but it's consistent enough that I can recognize it quickly.) I'll admit I'm pretty new to delta printers, but I'd think that extrusion issues (if from the extruder or from the hot end) would be either a complete mess or more random.

As well, and I'm not sure if it means anything, notice how the two prints posted above, differing only in the direction the lines are printed, look as if they are almost mirrors of each other. Not perfect mirrors, but I wonder if it's significant or not.

Danal

@garyd9 said in Major delta problems:

nozzle

Replace the nozzle. Seriously. On a Prusa Mk3 that had printed for about two weeks straight out of the box, printed VERY good prints such as the one on the left (and keep in mind that these are single wall prints, for flying radio control models; very challenging print) to the one on the right, suddenly and for no reason.

I cleaned the nozzle a dozen ways, cold pulls, hot pulls, different filament, you name it. Still printed like crap.

CHANGED the nozzle, and Viola! Printing just fine again. Put a $0.70 nozzle in it...

Oh... and I don't have a pic... but one print in between really good and really bad just showed surface oddness, somewhat like yours.

ayudtee

Something I think being missed is that this "pattern" is fairly consistent.

Consistency makes me think the problem is with your motion-mechanics. If the problem was with the nozzle you would not be experiencing this consistency. I think that something new has either loosed up, or is now binding. Do you see anything wiggle when you attempt to move the effector around with one finger pushing under the hotend? Is your Orion mount still ok? Pulley grubscrews and effector rod connections still tight? Motor mount screws tight? Carriages still free? Also examine the drive belts carefully for damage or stretch marks.

garyd9

@danal said in Major delta problems:

I cleaned the nozzle a dozen ways, cold pulls, hot pulls, different filament, you name it. Still printed like crap.

CHANGED the nozzle, and Viola! Printing just fine again. Put a $0.70 nozzle in it...

Were the surface oddities consistent across prints? ie: same patterns?

garyd9

@ayudtee said in Major delta problems:

Consistency makes me think the problem is with your motion-mechanics. If the problem was with the nozzle you would not be experiencing this consistency. I think that something new has either loosed up, or is now binding. Do you see anything wiggle when you attempt to move the effector around with one finger pushing under the hotend? Is your Orion mount still ok? Pulley grubscrews and effector rod connections still tight? Motor mount screws tight? Carriages still free? Also examine the drive belts carefully for damage or stretch marks.

I've completely replaced all three belts, completely removed all three carriages, removed the wheels from the carriages and reattached them. The carriages show good movement when attached. I've checked (and replaced) the pulley gears at the steppers, and the idler pulleys. I'm currently investigating if the issue might be related to the orion (but shoving so much teflon tape on to the orion->extruder mounting joint that I cracked my titan cover re-attaching it. I might also try to completely remove the orion from between the extruder and E3DV6 and see if that helps.

Pardon me while I go order another titan extruder cover.

ayudtee

Pardon me while I go order another titan extruder cover.

I replaced the clickety-clackety titan on my Kossel this summer with a Bondtech BMG. (After reading @deckingman's excellent review.) Do yourself a favor, you won't regret it.

garyd9

@ayudtee said in Major delta problems:

Pardon me while I go order another titan extruder cover.

I replaced the clickety-clackety titan on my Kossel this summer with a Bondtech BMG. (After reading @deckingman's excellent review.) Do yourself a favor, you won't regret it.

I plan on it, eventually. First I want to get all my existing problems solved before I go and change all the variables again.

garyd9

Tomorrow, I'll try replacing the stepper motor on the Y tower. The idea is that I was having good prints (even if the binding on Y was causing other issues) before I replaced that stepper, and as far as I've been able to recreate, the issue started shortly after replacing the stepper. It might be the motor, the wiring, or something I did while replacing the motor.

It doesn't appear to be jerking or moving abnormally, but it can't hurt to try to replace it, and considering that it's a 0.9 degree stepper with microstepping set to 64, I doubt I'd be able to directly detect any flaw in the movement.

garyd9

Replacing the stepper motor didn't help.