My duetwifi seems to have died :(

gzcwnk

Step bed temp, temp rises OK.

gzcwnk

M115
SENDING:M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.16 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2016-11-08

M115
SENDING:M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.16 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2016-11-08

So its "alive" I suppose

gzcwnk

So updating firmware I get,

M997 S0
Error: In-application programming binary "iap4e.bin" not found
[ERROR] Error: In-application programming binary "iap4e.bin" not found

gzcwnk

Ok found that….installed it to /sys.

SENDING:M997 S1
Trying to connect at 230400 baud:
success
Erasing 4096 bytes...
Erasing 233472 bytes...
Uploading file...
5% complete
10% complete
15% complete
20% complete
25% complete
30% complete
35% complete
40% complete
45% complete
50% complete
55% complete
60% complete
65% complete
70% complete
75% complete
80% complete
85% complete
90% complete
95% complete
Upload successful

Phaedrux

Before trying to update the firmware on maybe not working hardware try disabling and reenabling the wifi module.

M552 S0
M552 S1

What does m552 return in pronterface?

Phaedrux

Well at least it was successful?

gzcwnk

m115
SENDING:M115
FIRMWARE_NAME: RepRapFirmware for Duet WiFi FIRMWARE_VERSION: 1.20 ELECTRONICS: Duet WiFi 1.0 FIRMWARE_DATE: 2017-12-23

M587 S"24G" P"mypassword" never returns. Nothing on wifi router.

Trying to set up the wifi and no workie

Phaedrux

There are pretty specific steps for upgrading to 1.20 from an older firmware. It's a bit of a change from previous updates. Did you follow those steps?

gzcwnk

Ok when I send the above it switches my password to uppercase by the look of it. M552 S1 says wrong password

Phaedrux

https://duet3d.dozuki.com/Wiki/Firmware_Overview#Section_Installing_and_Updating_Firmware

https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Upgrading_to_DuetWiFiFirmware_1_Num_19

gzcwnk

as far as I know.

gzcwnk

Ok so this is a 3rd set of instructions!

gzcwnk

OK so its all upper case so I need to find something else to send commands with

gzcwnk

M98 P/macros/SetNetwork
Warning: Macro file /macros/SetNetwork not found.<lf>ok<lf>Warning: Macro file /macros/SetNetwork not found.<lf>ok <lf>hmmm something wrong here…</lf></lf></lf></lf>

gzcwnk

M552 S1
ok<lf>WiFi module started <lf>M587
Remembered networks:<lf>24G IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0<lf>24G_IOT IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0<lf>ok<lf>WiFi reported error: Wrong password while trying to connect to 24G<lf>Wifi module is idle <lf>?

It can see 24G so wifi hardware must be OK?

I know the password is correct.</lf></lf></lf></lf></lf></lf></lf></lf>

gzcwnk

M587 S"G24" P"xxxxxxx"
M587: Failed to add SSID to remembered list<lf>ok <lf>?</lf></lf>

gzcwnk

OK I am failing to get an IP address.

gzcwnk

(COM7) Remembered networks:<lf>24G IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0<lf>24G_IOT IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0<lf>G24 IP=0.0.0.0 GW=0.0.0.0 NM=0.0.0.0<lf>ok<lf>WiFi reported error: Wrong password while trying to connect to 24G<lf>Wifi module is idle</lf></lf></lf></lf></lf></lf>

gzcwnk

OK I tried a new network,

(COM7) M587 S"G24_IoT" P"stevenjones"
(COM7) ok <lf>(COM7) M552 S1
(COM7) ok<lf>WiFi reported error: Wrong password while trying to connect to 24G<lf>Wifi module is idle <lf>I cant see it being a wrong password!</lf></lf></lf></lf>

dc42

1. How are you sending the M587 command? If you are using Pronterface or a similar USB host program, it is probably converting the characters in the password to uppercase.

2. Check that your router encryption is set to WPA2-PSK.