Many problems with 3.5.2

Phaedrux

Have you tried rolling back to 3.5.1 to verify that things go back to normal?

3DOeste

@Phaedrux No.. Do I just flash previus firmware or do I need to do some steps?

droftarts

@3DOeste said in Many problems with 3.5.2:

SD card longest read time 250.0ms, write time 568.1ms, max retries 0

Your longest read and write times don't look great. I think this is an SD card issue. Copy the files off the SD card onto your PC, reformat the SD card, then copy the files back on. If you want to test the SD card first, see https://docs.duet3d.com/en/User_manual/RepRapFirmware/SD_card#troubleshooting-sd-card-issues
For formatting, or replacement, see earlier on the above page.

Ian

Phaedrux

@3DOeste said in Many problems with 3.5.2:

@Phaedrux No.. Do I just flash previus firmware or do I need to do some steps?

You'd upload the firmware zip file from the release you want.

https://github.com/Duet3D/RepRapFirmware/releases/download/3.5.1/Duet2and3Firmware-3.5.1.zip

3DOeste

Well, it took me some time since I needed to finish some jobs, but I changed the SD card, although I couldn't find anything wrong with the old one. I was trying the .dummy upload with a large file, and it disconnect after a short while. I I run M122 after it reconnect I can see 250ms for longest read time, but inmediately after if I run M122 again it shows 5.2ms.
It's worth mentioning that I have absolutely no problems while printing. I didn't have a single print failure even after 3 days of continuous printing.

Also while writing this I tried to do a large simulation and it did it ok without disconnections.

3DOeste

I reflashed 3.5.1 and all the awkward delays are gone. Commands from panel due are instantaneous.
With 3.5.2 everything works, but has a delay before commands are executed.
So for now I'll stay with 3.5.1.

droftarts

@3DOeste Did you update DWC to 3.5.2 as well? Possibly old DWC files in the SD card /www folder are causing an issue. Also worth clearing browser cache for DWC and the ip address of the printer, and reloading the page in the browser. It is possible that there was some problem with the flash to 3.5.2, so worth redownloading 3.5.2 fresh and reflashing, if/when you want to update.

Ian

3DOeste

Hi, I'm sure DWC was on 3.5.2, and also try again from 3.5.1 to 3.5.2 and I have the slow response from commands from panel due (and also from DWC), back to 3.5.1 again and everithing runs fine.

droftarts

@3DOeste A suggestion from @chrishamm is to update to 3.5.2 and disconnect the PanelDue, and see if that makes a difference to the responsiveness of DWC. How is the PanelDue connected? By 4-wire cable, ribbon cable, or both?

Ian

3DOeste

It's connected with a 4-wire cable. I'll test disconnecting the PanelDue as soon as the current print is finished.

dc42

@3DOeste instead of disconnecting the PanelDue it is sufficient to leave it displaying its Setup page.

3DOeste

@dc42 Hi, I tried that, and it works ok. Today I installed 3.5.3, same behaviour as 3.5.2, but if after homing, I enter the panel due setup page, and then back to status, everything works as it should, without weird delays. It doesn't happen with 3.5.1.

dc42

@3DOeste thanks for the feedback. We added a check in 3.5.2 to reduce the chance of consistently running our of buffers when both PanelDue and DWC are active. It appears that this check is having a side-effect in your system. I have created this issue https://github.com/Duet3D/RepRapFirmware/issues/1047.

dc42 created this issue in Duet3D/RepRapFirmware

open Startup issues when PanelDue and DWC are both active #1047

AlexKid

Looks and sounds like the same issue I have.
https://forum.duet3d.com/topic/36643/randomly-reconnect-of-dwc-on-duet2-ethernet?_=1727016238232 isn't it? Started with 3.5.2 and also present with 3.5.3.