Zaribo / Prusa i3 MK3s - Duet 2 WiFi - RRF 3.11

[Kolbi]

@Phaedrux Thanks much!

I saw the {1} and tried to get rid of them but for some reason, it didn't work.
I did attach my dump-list.pdf so people could view it there also - I keep this one updated too.

I'll give it a shot once I get some time this evening. Do you know what causes them?

Cheers,
Kolbi

[Phaedrux]

@Kolbi said in Zaribo / Prusa i3 MK3s - Duet 2 WiFi - RRF 3.11:

Do you know what causes them?

They seem to show up on line breaks within the code blocks for some reason. It's a forum issue.

[Kolbi]

@Phaedrux said in Zaribo / Prusa i3 MK3s - Duet 2 WiFi - RRF 3.11:

show up on line breaks within the code blocks

Ah! Just add a space after a line break and that gets rid of it.

[Phaedrux]

Good to know!

[A Former User]

@Phaedrux said in Zaribo / Prusa i3 MK3s - Duet 2 WiFi - RRF 3.11:

They seem to show up on line breaks within the code blocks for some reason. It's a forum issue.

not for all types of code interestingly enough, but haven't experimented with the complete list of language highlighting.

[Kolbi]

Updated stop.g, focused on getting rid of spider web / hair like stringing from nozzle while leaving nothing on nozzle.

; 0:/sys/stop.g
; called when M0 (Stop) is run (e.g. when a print from SD card is cancelled)

M83                                                        ; Set extruder to relative mode
M106 S255                                                  ; Turn fan fully on
M572 D0 S0.0                                               ; clear pressure advance
M220 S100                                                  ; Set speed factor back to 100% in case it was changed
M221 S100                                                  ; Set extrusion factor back to 100% in case it was changed
G1 E-2                                                     ; Retract 2mm
M104 S-273                                                 ; Turn off hotend
M140 S-273                                                 ; Turn off heatbed
G1 F1000.0                                                 ; Set feed rate
M98 P"current-sense-homing.g"                              ; Adjust current and sensitivity for homing routines

; Let cool and wiggle for bit to reduce end stringing
M300 S4000 P100 G4 P200 M300 S4000 P100                    ; Give a double beep
G91                                                        ; Set to Relative Positioning
G1 Z2 F400                                                 ; Move Z up 3mm

; Start countdown - use X/Y as indicators of counting  
while iterations <=9                                       ; Perform 10 passes
    G4 S6                                                  ; Wait 6 seconds
    G1 X1 Y1 F1000                                         ; Wiggle +1mm
    G4 S6                                                  ; Wait 6 seconds
    G1 Z0.5 X-1 Y-1 F1000                                  ; Wiggle -1mm, Z +0.5

G90                                                        ; Set to Absolute Positioning

G1 X220 Y205 Z205 F1000                                    ; Place nozzle to the right side, build plate to front, Z at top
M400                                                       ; Clear queue
M107                                                       ; Turn off fan
M18 YXE                                                    ; Unlock X, Y, and E axis

; Play a triumphant tune to celebrate a successful print.
G4 S1
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S750
G4 P251
M300 P200 S1250
G4 P201
M300 P250 S2500
G4 P251
M300 P150 S2000
G4 P151
M300 P150 S2500
G4 P151
M300 P350 S3700
G4 P351
M400

[Kolbi]

Attached modified BMGm-BLTouch.
Offsets at X22.8, Y3.8, Z1.32.

10068-6 Prusa Housing Rear MK3s MosquitoV1.4.STL 10068-7 Prusa Housing Front MK3s MosquitoV1.4.STL

[Kolbi]

Forgot the bltouch wire cover.
bltouch-wirecover.STL

*The front and back parts require threaded inserts.

[e4d]

Hello @Kolbi do you have an enclosure for Duet wifi that mount to the printer ? I’d love to have an STL if you mind sharing

[Kolbi]

@e4d Sorry, It's been a while and I don't have that on my latest laptop. I'll give a search on my home server when I get a chance to see if I may have backed it up.
But, give a look at the caribou github - variants from duet 2 and 3mini exist.
https://github.com/Caribou3d/CaribouCartesian/tree/master/STL/01_full-kits/Frame/Duet

Hope that helps!