Only probe where the part will be printed

Proschi3D

@danym21 Error: in GCode file line 182 column 7: M221: expected number after 'S'
Extruder pressure advance: 0.065, 0.000
Error: in file macro line 8 column 8: M557: unknown value 'first_layer_print_min^'

can you give me your whole start code ?
and mesh.g ?

danym21

@Proschi78
start G-Code:

G90 ; use absolute coordinates
;M83  ; extruder relative mode
;BED_MESH_CALIBRATE AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]}
;MINX:{first_layer_print_min[0]}
;MINY:{first_layer_print_min[1]}
;MAXX:{first_layer_print_max[0]}
;MAXY:{first_layer_print_max[1]}
M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]}
M82 ; absolute extrusion mode
M104 S140 T0
M140 S[first_layer_bed_temperature] ; set bed temp
M190 S[first_layer_bed_temperature] ; wait for bed temp
G32 ; home all
G1 X-14 Y-10 F10000
; Reset speed and extrusion rates
M200 D0 ; disable volumetric e
M220 S100 ; reset speed
M221 S100 D0 ; reset extrusion rate
M109 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; wait for extruder temp
G92 E0.0

;G1 X150.0 E20  F1000.0 ; intro line
G1 E20  F1000.0 ; intro line
G1 X0.0 Y0.0 Z0.1 F1000.0 ; go outside print area
;G1 X5 Y0
G92 E0.0
G1 X2 Y2 Z0.2 E0 F18000 ; new
G1 X60 Y2 E9.0 F1800 ;intro Line
;G1 X200.0 E30 F500 ; second Part intro Line
G92 E0.0
G1 Z5 E-{retract_length[0]} F{retract_speed *60}
G1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} Z{first_layer_height} F30000
G1 E{retract_length[0]} F{retract_speed*60}
G92 E0.0

I do not use a mesh.g this does not exists on my system
my bed.g:

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 01:08:02 GMT+0100 (Mitteleuropäische Normalzeit)
M561 ; clear any bed transform
G4 P100
G28 ; home
G0 Z10 F4200

G0 F60000
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G0 X45 Y-5 F60000
G29 										;Probe the heatbed and generate heightmap

G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G4 P100
G0 X0 Y0 F60000 						;Go to Parking Position

some settings in config.g that maybe relevant for:

...
M671 X-52:377 Y155:155 S2.5 					   ; leadscrews at left (connected to Z) and right
...
M557 X10:300 Y10:300 P6:6; S40                     ; define mesh grid ( the normal full size mesh config)

Proschi3D

jetzt gehts
now it works

danym21

@Proschi78

Proschi3D

@danym21 Do you also have start codes for other slicers?

danym21

@Proschi78
no, sorry
but on S3d maybe have a look to this variables:
I do not know what is in, but you can test with a smal object and check then the gcode file

[build_size_x]
[build_size_y]
[build_size_z]
....
[next_position_x]
[next_position_y]
[next_position_z]

they are mentioned here:
https://community.ultimaker.com/topic/11328-simplify3d-hidden-undocumented-placeholders-for-post-processing-scripts/

Proschi3D

@danym21 thanks I'll test that tomorrow

Proschi3D

@danym21 said in Only probe where the part will be printed:

@Proschi78
start G-Code:

G90 ; use absolute coordinates
;M83  ; extruder relative mode
;BED_MESH_CALIBRATE AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]}
;MINX:{first_layer_print_min[0]}
;MINY:{first_layer_print_min[1]}
;MAXX:{first_layer_print_max[0]}
;MAXY:{first_layer_print_max[1]}
M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]}
M82 ; absolute extrusion mode
M104 S140 T0
M140 S[first_layer_bed_temperature] ; set bed temp
M190 S[first_layer_bed_temperature] ; wait for bed temp
G32 ; home all
G1 X-14 Y-10 F10000
; Reset speed and extrusion rates
M200 D0 ; disable volumetric e
M220 S100 ; reset speed
M221 S100 D0 ; reset extrusion rate
M109 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; wait for extruder temp
G92 E0.0

;G1 X150.0 E20  F1000.0 ; intro line
G1 E20  F1000.0 ; intro line
G1 X0.0 Y0.0 Z0.1 F1000.0 ; go outside print area
;G1 X5 Y0
G92 E0.0
G1 X2 Y2 Z0.2 E0 F18000 ; new
G1 X60 Y2 E9.0 F1800 ;intro Line
;G1 X200.0 E30 F500 ; second Part intro Line
G92 E0.0
G1 Z5 E-{retract_length[0]} F{retract_speed *60}
G1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} Z{first_layer_height} F30000
G1 E{retract_length[0]} F{retract_speed*60}
G92 E0.0

I do not use a mesh.g this does not exists on my system
my bed.g:

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 01:08:02 GMT+0100 (Mitteleuropäische Normalzeit)
M561 ; clear any bed transform
G4 P100
G28 ; home
G0 Z10 F4200

G0 F60000
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G0 X45 Y-5 F60000
G29 										;Probe the heatbed and generate heightmap

G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G4 P100
G0 X0 Y0 F60000 						;Go to Parking Position

some settings in config.g that maybe relevant for:

...
M671 X-52:377 Y155:155 S2.5 					   ; leadscrews at left (connected to Z) and right
...
M557 X10:300 Y10:300 P6:6; S40                     ; define mesh grid ( the normal full size mesh config)

what can I do with this start code so that it is probing in mesh like A5 in normal mesh?
Best off five ?

danym21

@Proschi78 said in Only probe where the part will be printed:

ke A5 in no

the A5 needs to be in the config.g where you configure the probe type
look for M558
https://docs.duet3d.com/User_manual/Reference/Gcodes#m558-set-z-probe-type

Proschi3D

@danym21
Hello,
I know that and I also have it in the config.g
but if I start a print and it only creates the mesh where the printed part is, then it only runs once in z

M558 P1 C"io3.in" H5 A5 S0.009 F150 T6000                           ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z1.730; set Z probe trigger value, offset and trigger height
M557 X30:330 Y-3:210 P9

danym21

@Proschi78
mhm, this makes no sense for me, do you have a M558 on some other positions? like in the the bed.g or config-override.g?

I will test this when I have time for, I normaly use only one probe per point.

mher

Just want to share the solution I made for this a couple of months ago (posted here)
as well.

It works with PrusaSlicer/SuperSlicer, Cura and Ideamaker. Instructions are included as well.
https://github.com/MaikoHermans/RRF-PAM

Proschi3D

Has anyone managed to do it with simplify v5?

IndeX4D

@Proschi78

I would like to know the same