Only probe where the part will be printed
-
@Proschi78
The M140, M190 & M109 commands that are causing the errors are in your code, not mine.
Most likely in your start G Code
It looks like you're using incorrect place holders for the tempsPlease post the start GCode from Prusa Slicer
-
@OwenD
PS start codeM703 ; Load Filament specific config, including Temps M98 P"/sys/start/Prusalinks"
Macro
T0 M572 D0 S0.065 M572 D1 D0.065 G90 ; set printer absolute mode M82 ; set extruder to absolute mode M106 S0 ; fan off ;M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points G28 ; home all axes G28 Z0 G29 G29 s1 T0 ; set first toolhead G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line G92 E0 ; set position ; intro line T0 G1 Z0.35 F6000 ; G1 X60 Y-2 F6000 ; G1 X140 Y-2 E20 F200 ; G1 x160 y-2 F5000 G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed G1 x170 y-2 F2000 G92 E0 ; set position G1 F9000.0 ; M117 Printing...
-
@Proschi78
Where are you setting your temps?
If it's in your filament config.g then post that too.
If you don't put heater settings in PS start code, it will probably do it for you.
So if you want to set your temps in the filament config.g then put a dummy setting in your PS start code. -
Extruder pressure advance: 0.065, 0.100 Error: in file macro line 6 column 59: meta command: expected numeric operands Cancelled printing file 0:/gcodes/Part 27 - Part 1.gcode, print time was 0h 0m 20.12.2022, 20:56:33 M32 "0:/gcodes/Part 27 - Part 1.gcode" File 0:/gcodes/Part 27 - Part 1.gcode selected for printing
T0 M572 D0 S0.065 M572 D1 D0.065 G90 ; set printer absolute mode M82 ; set extruder to absolute mode M106 S0 ; fan off M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points G28 ; home all axes G28 Z G29 G29 S1 T0 ; set second toolhead G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line G92 E0 ; set position ; intro line G1 Z0.35 F6000 ; G1 X60 Y-2 F6000 ; G1 X140 Y-2 E20 F200 ; G1 x160 y-2 F5000 G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed G1 x170 y-2 F2000 G92 E0 ; set position G1 F9000.0 ; M106 P3 S33 M117 Printing...
-
@Proschi78
I'm unsure where the code you have posted is located.
Please try the following in your Prusa Start GCode.
Don't call any other macros from Prusa!M118 S"Begin slicer start g code" ;M104 S0 R0 P{current_extruder} ;Dummy Set temps to zero to stop slicer adding them T{current_extruder} ; select tool used on first layer M703 ; load config file for [filament_type] G90 ; Switch to using Absolute Coordinates M82 ; set extruder to absolute mode M568 P{current_extruder} R{"{heat.coldExtrudeTemperature+5}"} S{first_layer_temperature[current_extruder]} A1 ; (set extruder to stanby to soften any protruding filament before probing ) M106 P{current_extruder} S0 ;Start with fan off M118 S"Heating Bed" G4 S1 M140 S{first_layer_bed_temperature[current_extruder]} R{bed_temperature[0]-20}; Set fast bed temp & standby - Standby is 20 degrees less than normal. M116 ; Wait for bed before doing mesh probe. M561 ; clear any bed transform M291 S0 T3 P"Homing..." G28 ; Home all M400 ; wait for last move M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points G29 S1 ; load small mesh G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line G92 E0 ; set position ; intro line G1 Z0.35 F6000 ; G1 X60 Y-2 F6000 ; G1 X140 Y-2 E20 F200 ; G1 x160 y-2 F5000 G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed G1 x170 y-2 F2000 G92 E0 ; set position G1 F9000.0 ; M106 P3 S33 M117 Printing...
-
Error: in file macro line 6 column 59: meta command: expected numeric operands Cancelled printing file 0:/gcodes/Part 27 - Part 2.gcode, print time was 0h 2m 20.12.2022, 21:53:49 M32 "0:/gcodes/Part 27 - Part 2.gcode" File 0:/gcodes/Part 27 - Part 2.gcode selected for printing Begin slicer start g code Heating Bed
If I exclude M98 then normal mesh leveling and printing work.
M118 S"Begin slicer start g code" ;M104 S0 R0 P{current_extruder} ;Dummy Set temps to zero to stop slicer adding them T{current_extruder} ; select tool used on first layer M703 ; load config file for [filament_type] G90 ; Switch to using Absolute Coordinates M82 ; set extruder to absolute mode M568 P{current_extruder} R{"{heat.coldExtrudeTemperature+5}"} S{first_layer_temperature[current_extruder]} A1 ; (set extruder to stanby to soften any protruding filament before probing ) M106 P{current_extruder} S0 ;Start with fan off M118 S"Heating Bed" G4 S1 M140 S{first_layer_bed_temperature[current_extruder]} R{bed_temperature[0]-20}; Set fast bed temp & standby - Standby is 20 degrees less than normal. M116 ; Wait for bed before doing mesh probe. M561 ; clear any bed transform M291 S0 T3 P"Homing..." G28 ; Home all M400 ; wait for last move ;M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points G29 G29 S1 ; load small mesh G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line G92 E0 ; set position ; intro line G1 Z0.35 F6000 ; G1 X60 Y-2 F6000 ; G1 X140 Y-2 E20 F200 ; G1 x160 y-2 F5000 G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed G1 x170 y-2 F2000 G92 E0 ; set position G1 F9000.0 ; M106 P3 S33 M117 Printing...
-
@Proschi78
Hi, I use SuperSlicer, but I think in prusa Slicer it should also work.
in my startcode I added this line:M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]}
maybe this will help you too.
-
@danym21 Error: in GCode file line 182 column 7: M221: expected number after 'S'
Extruder pressure advance: 0.065, 0.000
Error: in file macro line 8 column 8: M557: unknown value 'first_layer_print_min^'can you give me your whole start code ?
and mesh.g ? -
@Proschi78
start G-Code:G90 ; use absolute coordinates ;M83 ; extruder relative mode ;BED_MESH_CALIBRATE AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} ;MINX:{first_layer_print_min[0]} ;MINY:{first_layer_print_min[1]} ;MAXX:{first_layer_print_max[0]} ;MAXY:{first_layer_print_max[1]} M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]} M82 ; absolute extrusion mode M104 S140 T0 M140 S[first_layer_bed_temperature] ; set bed temp M190 S[first_layer_bed_temperature] ; wait for bed temp G32 ; home all G1 X-14 Y-10 F10000 ; Reset speed and extrusion rates M200 D0 ; disable volumetric e M220 S100 ; reset speed M221 S100 D0 ; reset extrusion rate M109 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; wait for extruder temp G92 E0.0 ;G1 X150.0 E20 F1000.0 ; intro line G1 E20 F1000.0 ; intro line G1 X0.0 Y0.0 Z0.1 F1000.0 ; go outside print area ;G1 X5 Y0 G92 E0.0 G1 X2 Y2 Z0.2 E0 F18000 ; new G1 X60 Y2 E9.0 F1800 ;intro Line ;G1 X200.0 E30 F500 ; second Part intro Line G92 E0.0 G1 Z5 E-{retract_length[0]} F{retract_speed *60} G1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} Z{first_layer_height} F30000 G1 E{retract_length[0]} F{retract_speed*60} G92 E0.0
I do not use a mesh.g this does not exists on my system
my bed.g:; bed.g ; called to perform automatic bed compensation via G32 ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 01:08:02 GMT+0100 (Mitteleuropäische Normalzeit) M561 ; clear any bed transform G4 P100 G28 ; home G0 Z10 F4200 G0 F60000 G30 P0 X5 Y155 Z-99999 ;Orbiter G30 P1 X302 Y155 Z-99999 S2 ;Orbiter G30 P0 X5 Y155 Z-99999 ;Orbiter G30 P1 X302 Y155 Z-99999 S2 ;Orbiter G91 ;Relative positioning G1 Z5 F1500 ;Raise Z 5mm G90 ;Absolute positioning G0 X45 Y-5 F60000 G29 ;Probe the heatbed and generate heightmap G91 ;Relative positioning G1 Z5 F1500 ;Raise Z 5mm G90 ;Absolute positioning G4 P100 G0 X0 Y0 F60000 ;Go to Parking Position
some settings in config.g that maybe relevant for:
... M671 X-52:377 Y155:155 S2.5 ; leadscrews at left (connected to Z) and right ... M557 X10:300 Y10:300 P6:6; S40 ; define mesh grid ( the normal full size mesh config)
-
jetzt gehts
now it works -
@Proschi78
-
@danym21 Do you also have start codes for other slicers?
-
@Proschi78
no, sorry
but on S3d maybe have a look to this variables:
I do not know what is in, but you can test with a smal object and check then the gcode file[build_size_x] [build_size_y] [build_size_z] .... [next_position_x] [next_position_y] [next_position_z]
they are mentioned here:
https://community.ultimaker.com/topic/11328-simplify3d-hidden-undocumented-placeholders-for-post-processing-scripts/ -
@danym21 thanks I'll test that tomorrow
-
@danym21 said in Only probe where the part will be printed:
@Proschi78
start G-Code:G90 ; use absolute coordinates ;M83 ; extruder relative mode ;BED_MESH_CALIBRATE AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]} ;MINX:{first_layer_print_min[0]} ;MINY:{first_layer_print_min[1]} ;MAXX:{first_layer_print_max[0]} ;MAXY:{first_layer_print_max[1]} M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]} M82 ; absolute extrusion mode M104 S140 T0 M140 S[first_layer_bed_temperature] ; set bed temp M190 S[first_layer_bed_temperature] ; wait for bed temp G32 ; home all G1 X-14 Y-10 F10000 ; Reset speed and extrusion rates M200 D0 ; disable volumetric e M220 S100 ; reset speed M221 S100 D0 ; reset extrusion rate M109 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; wait for extruder temp G92 E0.0 ;G1 X150.0 E20 F1000.0 ; intro line G1 E20 F1000.0 ; intro line G1 X0.0 Y0.0 Z0.1 F1000.0 ; go outside print area ;G1 X5 Y0 G92 E0.0 G1 X2 Y2 Z0.2 E0 F18000 ; new G1 X60 Y2 E9.0 F1800 ;intro Line ;G1 X200.0 E30 F500 ; second Part intro Line G92 E0.0 G1 Z5 E-{retract_length[0]} F{retract_speed *60} G1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} Z{first_layer_height} F30000 G1 E{retract_length[0]} F{retract_speed*60} G92 E0.0
I do not use a mesh.g this does not exists on my system
my bed.g:; bed.g ; called to perform automatic bed compensation via G32 ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 01:08:02 GMT+0100 (Mitteleuropäische Normalzeit) M561 ; clear any bed transform G4 P100 G28 ; home G0 Z10 F4200 G0 F60000 G30 P0 X5 Y155 Z-99999 ;Orbiter G30 P1 X302 Y155 Z-99999 S2 ;Orbiter G30 P0 X5 Y155 Z-99999 ;Orbiter G30 P1 X302 Y155 Z-99999 S2 ;Orbiter G91 ;Relative positioning G1 Z5 F1500 ;Raise Z 5mm G90 ;Absolute positioning G0 X45 Y-5 F60000 G29 ;Probe the heatbed and generate heightmap G91 ;Relative positioning G1 Z5 F1500 ;Raise Z 5mm G90 ;Absolute positioning G4 P100 G0 X0 Y0 F60000 ;Go to Parking Position
some settings in config.g that maybe relevant for:
... M671 X-52:377 Y155:155 S2.5 ; leadscrews at left (connected to Z) and right ... M557 X10:300 Y10:300 P6:6; S40 ; define mesh grid ( the normal full size mesh config)
what can I do with this start code so that it is probing in mesh like A5 in normal mesh?
Best off five ? -
@Proschi78 said in Only probe where the part will be printed:
ke A5 in no
the A5 needs to be in the config.g where you configure the probe type
look for M558
https://docs.duet3d.com/User_manual/Reference/Gcodes#m558-set-z-probe-type -
@danym21
Hello,
I know that and I also have it in the config.g
but if I start a print and it only creates the mesh where the printed part is, then it only runs once in zM558 P1 C"io3.in" H5 A5 S0.009 F150 T6000 ; set Z probe type to unmodulated and the dive height + speeds G31 P500 X0 Y0 Z1.730; set Z probe trigger value, offset and trigger height M557 X30:330 Y-3:210 P9
-
@Proschi78
mhm, this makes no sense for me, do you have a M558 on some other positions? like in the the bed.g or config-override.g?I will test this when I have time for, I normaly use only one probe per point.
-
Just want to share the solution I made for this a couple of months ago (posted here)
as well.It works with PrusaSlicer/SuperSlicer, Cura and Ideamaker. Instructions are included as well.
https://github.com/MaikoHermans/RRF-PAM -
Has anyone managed to do it with simplify v5?
-
-
-
-
-