Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Only probe where the part will be printed

    Scheduled Pinned Locked Moved
    Gcode meta commands
    5
    26
    1.8k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Proschi3Dundefined
      Proschi3D @OwenD
      last edited by

      This post is deleted!
      1 Reply Last reply Reply Quote 0
      • Proschi3Dundefined
        Proschi3D @OwenD
        last edited by Proschi3D

        @OwenD the mesh works but printing is canceled

        	Extruder pressure advance: 0.065, 0.000
Error: in file macro line 7 column 7: M140: expected number after 'S'
Error: Bad command: mperature] 
Error: in file macro line 8 column 11: M190: expected number after 'r'
Error: Bad command: mperature] 
Error: in file macro line 9 column 11: M109: expected number after 'r'
Error: Bad command: mperature] T0 
Error: in file macro line 4 column 39: meta command: expected numeric operands
Cancelled printing file 0:/gcodes/Part 27 - Part 2.gcode, print time was 0h 2m
20.12.2022, 17:17:40	4 points probed, min error -0.233, max error -0.025, mean -0.132, deviation 0.078
Height map saved to file 0:/sys/heightmap.csv
20.12.2022, 17:17:28	Probe distance used: 60 mm
xMin = max( 15.0 121.681 )
xMax = min( 325.0 213.662 )
yMin = max( -15.0 75.8219 )
yMax = min( 210.0 153.294 )
20.12.2022, 17:14:32	Connected to 192.168.178.91
        OwenDundefined 1 Reply Last reply Reply Quote 0
        • OwenDundefined
          OwenD @Proschi3D
          last edited by

          @Proschi78
          The M140, M190 & M109 commands that are causing the errors are in your code, not mine.
          Most likely in your start G Code
          It looks like you're using incorrect place holders for the temps

          Please post the start GCode from Prusa Slicer

          Proschi3Dundefined 1 Reply Last reply Reply Quote 0
          • Proschi3Dundefined
            Proschi3D @OwenD
            last edited by

            @OwenD
            PS start code

            M703		; Load Filament specific config, including Temps
M98 P"/sys/start/Prusalinks"

            Macro

            T0
M572 D0 S0.065
M572 D1 D0.065
G90 ; set printer absolute mode
M82 ; set extruder to absolute mode
M106 S0 ; fan off
;M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points
G28 ; home all axes
G28 Z0
G29
G29 s1
T0 ; set first toolhead
G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line
G92 E0 ; set position
; intro line
T0
G1 Z0.35 F6000 ;
G1 X60 Y-2 F6000 ;
G1 X140 Y-2 E20 F200 ;
G1 x160 y-2 F5000
G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed
G1 x170 y-2 F2000
G92 E0 ; set position
G1 F9000.0 ;
M117 Printing...
            OwenDundefined 1 Reply Last reply Reply Quote 0
            • OwenDundefined
              OwenD @Proschi3D
              last edited by

              @Proschi78
              Where are you setting your temps?
              If it's in your filament config.g then post that too.
              If you don't put heater settings in PS start code, it will probably do it for you.
              So if you want to set your temps in the filament config.g then put a dummy setting in your PS start code.

              Proschi3Dundefined 1 Reply Last reply Reply Quote 0
              • Proschi3Dundefined
                Proschi3D @OwenD
                last edited by Proschi3D

                @OwenD

                Extruder pressure advance: 0.065, 0.100
Error: in file macro line 6 column 59: meta command: expected numeric operands
Cancelled printing file 0:/gcodes/Part 27 - Part 1.gcode, print time was 0h 0m
20.12.2022, 20:56:33	M32 "0:/gcodes/Part 27 - Part 1.gcode"
File 0:/gcodes/Part 27 - Part 1.gcode selected for printing

                T0
M572 D0 S0.065
M572 D1 D0.065
G90 ; set printer absolute mode
M82 ; set extruder to absolute mode
M106 S0 ; fan off
M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points
G28 ; home all axes
G28 Z
G29
G29 S1
T0 ; set second toolhead
G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line
G92 E0 ; set position
; intro line
G1 Z0.35 F6000 ;
G1 X60 Y-2 F6000 ;
G1 X140 Y-2 E20 F200 ;
G1 x160 y-2 F5000
G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed
G1 x170 y-2 F2000
G92 E0 ; set position
G1 F9000.0 ;
M106 P3 S33
M117 Printing...
                OwenDundefined 1 Reply Last reply Reply Quote 0
                • OwenDundefined
                  OwenD @Proschi3D
                  last edited by OwenD

                  @Proschi78
                  I'm unsure where the code you have posted is located.
                  Please try the following in your Prusa Start GCode.
                  Don't call any other macros from Prusa!

                  M118 S"Begin slicer start g code"
;M104 S0 R0 P{current_extruder} ;Dummy  Set temps to zero to stop slicer adding them
T{current_extruder} ; select tool used on first layer
M703 ; load config file for [filament_type]
G90 ; Switch to using Absolute Coordinates
M82 ; set extruder to absolute mode
M568 P{current_extruder} R{"{heat.coldExtrudeTemperature+5}"} S{first_layer_temperature[current_extruder]} A1 ; (set extruder to stanby to soften any protruding filament before probing )
M106 P{current_extruder} S0 ;Start with fan off
M118 S"Heating Bed"
G4 S1
M140 S{first_layer_bed_temperature[current_extruder]}  R{bed_temperature[0]-20}; Set fast bed temp & standby - Standby is 20 degrees less than normal.
M116 ; Wait for bed before doing mesh probe.
M561 ; clear any bed transform
M291 S0 T3  P"Homing..."
G28 ; Home all 
M400 ; wait for last move
M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points
G29 S1  ; load small mesh
G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line
G92 E0 ; set position
; intro line
G1 Z0.35 F6000 ;
G1 X60 Y-2 F6000 ;
G1 X140 Y-2 E20 F200 ;
G1 x160 y-2 F5000
G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed
G1 x170 y-2 F2000
G92 E0 ; set position
G1 F9000.0 ;
M106 P3 S33
M117 Printing...
                  Proschi3Dundefined 1 Reply Last reply Reply Quote 0
                  • Proschi3Dundefined
                    Proschi3D @OwenD
                    last edited by Proschi3D

                    @OwenD

                    Error: in file macro line 6 column 59: meta command: expected numeric operands
Cancelled printing file 0:/gcodes/Part 27 - Part 2.gcode, print time was 0h 2m
20.12.2022, 21:53:49	M32 "0:/gcodes/Part 27 - Part 2.gcode"
File 0:/gcodes/Part 27 - Part 2.gcode selected for printing
Begin slicer start g code
Heating Bed

                    If I exclude M98 then normal mesh leveling and printing work.

                    M118 S"Begin slicer start g code"
;M104 S0 R0 P{current_extruder} ;Dummy  Set temps to zero to stop slicer adding them
T{current_extruder} ; select tool used on first layer
M703 ; load config file for [filament_type]
G90 ; Switch to using Absolute Coordinates
M82 ; set extruder to absolute mode
M568 P{current_extruder} R{"{heat.coldExtrudeTemperature+5}"} S{first_layer_temperature[current_extruder]} A1 ; (set extruder to stanby to soften any protruding filament before probing )
M106 P{current_extruder} S0 ;Start with fan off
M118 S"Heating Bed"
G4 S1
M140 S{first_layer_bed_temperature[current_extruder]}  R{bed_temperature[0]-20}; Set fast bed temp & standby - Standby is 20 degrees less than normal.
M116 ; Wait for bed before doing mesh probe.
M561 ; clear any bed transform
M291 S0 T3  P"Homing..."
G28 ; Home all 
M400 ; wait for last move
;M98 P"0:/sys/mesh.g" A{first_layer_print_min[0]} B{first_layer_print_max[0]} C{first_layer_print_min[1]} D{first_layer_print_max[1]} N60 ; set N to your desired distance between probe points
G29
G29 S1  ; load small mesh
G1 Z3 F2000 ; Move to Z3 for height clearance before Intro line
G92 E0 ; set position
; intro line
G1 Z0.35 F6000 ;
G1 X60 Y-2 F6000 ;
G1 X140 Y-2 E20 F200 ;
G1 x160 y-2 F5000
G1 Z5 F2000 ; Move to Z5 to prevent dragging nozzle and scratching bed
G1 x170 y-2 F2000
G92 E0 ; set position
G1 F9000.0 ;
M106 P3 S33
M117 Printing...
                    danym21undefined 1 Reply Last reply Reply Quote 0
                    • danym21undefined
                      danym21 @Proschi3D
                      last edited by

                      @Proschi78
                      Hi, I use SuperSlicer, but I think in prusa Slicer it should also work.
                      in my startcode I added this line:

                      M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]}

                      maybe this will help you too.

                      Proschi3Dundefined 1 Reply Last reply Reply Quote 0
                      • Proschi3Dundefined
                        Proschi3D @danym21
                        last edited by Proschi3D

                        @danym21 Error: in GCode file line 182 column 7: M221: expected number after 'S'
                        Extruder pressure advance: 0.065, 0.000
                        Error: in file macro line 8 column 8: M557: unknown value 'first_layer_print_min^'

                        can you give me your whole start code ?
                        and mesh.g ?

                        danym21undefined 1 Reply Last reply Reply Quote 0
                        • danym21undefined
                          danym21 @Proschi3D
                          last edited by

                          @Proschi78
                          start G-Code:

                          G90 ; use absolute coordinates
;M83  ; extruder relative mode
;BED_MESH_CALIBRATE AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]}
;MINX:{first_layer_print_min[0]}
;MINY:{first_layer_print_min[1]}
;MAXX:{first_layer_print_max[0]}
;MAXY:{first_layer_print_max[1]}
M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]}
M82 ; absolute extrusion mode
M104 S140 T0
M140 S[first_layer_bed_temperature] ; set bed temp
M190 S[first_layer_bed_temperature] ; wait for bed temp
G32 ; home all
G1 X-14 Y-10 F10000
; Reset speed and extrusion rates
M200 D0 ; disable volumetric e
M220 S100 ; reset speed
M221 S100 D0 ; reset extrusion rate
M109 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; wait for extruder temp
G92 E0.0

;G1 X150.0 E20  F1000.0 ; intro line
G1 E20  F1000.0 ; intro line
G1 X0.0 Y0.0 Z0.1 F1000.0 ; go outside print area
;G1 X5 Y0
G92 E0.0
G1 X2 Y2 Z0.2 E0 F18000 ; new
G1 X60 Y2 E9.0 F1800 ;intro Line
;G1 X200.0 E30 F500 ; second Part intro Line
G92 E0.0
G1 Z5 E-{retract_length[0]} F{retract_speed *60}
G1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} Z{first_layer_height} F30000
G1 E{retract_length[0]} F{retract_speed*60}
G92 E0.0

                          I do not use a mesh.g this does not exists on my system
                          my bed.g:

                          ; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 01:08:02 GMT+0100 (Mitteleuropäische Normalzeit)
M561 ; clear any bed transform
G4 P100
G28 ; home
G0 Z10 F4200

G0 F60000
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G0 X45 Y-5 F60000
G29 										;Probe the heatbed and generate heightmap

G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G4 P100
G0 X0 Y0 F60000 						;Go to Parking Position

                          some settings in config.g that maybe relevant for:

                          ...
M671 X-52:377 Y155:155 S2.5 					   ; leadscrews at left (connected to Z) and right
...
M557 X10:300 Y10:300 P6:6; S40                     ; define mesh grid ( the normal full size mesh config)
                          Proschi3Dundefined 2 Replies Last reply Reply Quote 1
                          • Proschi3Dundefined
                            Proschi3D @danym21
                            last edited by Proschi3D

                            jetzt gehts 🙂
                            now it works 🙂

                            danym21undefined 1 Reply Last reply Reply Quote 0
                            • danym21undefined
                              danym21 @Proschi3D
                              last edited by

                              @Proschi78
                              🙂

                              Proschi3Dundefined 1 Reply Last reply Reply Quote 1
                              • Proschi3Dundefined
                                Proschi3D @danym21
                                last edited by

                                @danym21 Do you also have start codes for other slicers?

                                danym21undefined 1 Reply Last reply Reply Quote 0
                                • danym21undefined
                                  danym21 @Proschi3D
                                  last edited by

                                  @Proschi78
                                  no, sorry
                                  but on S3d maybe have a look to this variables:
                                  I do not know what is in, but you can test with a smal object and check then the gcode file

                                  [build_size_x]
[build_size_y]
[build_size_z]
....
[next_position_x]
[next_position_y]
[next_position_z]

                                  they are mentioned here:
                                  https://community.ultimaker.com/topic/11328-simplify3d-hidden-undocumented-placeholders-for-post-processing-scripts/

                                  Proschi3Dundefined 1 Reply Last reply Reply Quote 1
                                  • Proschi3Dundefined
                                    Proschi3D @danym21
                                    last edited by

                                    @danym21 thanks I'll test that tomorrow

                                    1 Reply Last reply Reply Quote 0
                                    • Proschi3Dundefined
                                      Proschi3D @danym21
                                      last edited by Proschi3D

                                      @danym21 said in Only probe where the part will be printed:

                                      @Proschi78
                                      start G-Code:

                                      G90 ; use absolute coordinates
;M83  ; extruder relative mode
;BED_MESH_CALIBRATE AREA_START={first_layer_print_min[0]},{first_layer_print_min[1]} AREA_END={first_layer_print_max[0]},{first_layer_print_max[1]}
;MINX:{first_layer_print_min[0]}
;MINY:{first_layer_print_min[1]}
;MAXX:{first_layer_print_max[0]}
;MAXY:{first_layer_print_max[1]}
M557 X{first_layer_print_min[0]}:{first_layer_print_max[0]} Y{first_layer_print_min[1]}:{first_layer_print_max[1]}
M82 ; absolute extrusion mode
M104 S140 T0
M140 S[first_layer_bed_temperature] ; set bed temp
M190 S[first_layer_bed_temperature] ; wait for bed temp
G32 ; home all
G1 X-14 Y-10 F10000
; Reset speed and extrusion rates
M200 D0 ; disable volumetric e
M220 S100 ; reset speed
M221 S100 D0 ; reset extrusion rate
M109 S{first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} ; wait for extruder temp
G92 E0.0

;G1 X150.0 E20  F1000.0 ; intro line
G1 E20  F1000.0 ; intro line
G1 X0.0 Y0.0 Z0.1 F1000.0 ; go outside print area
;G1 X5 Y0
G92 E0.0
G1 X2 Y2 Z0.2 E0 F18000 ; new
G1 X60 Y2 E9.0 F1800 ;intro Line
;G1 X200.0 E30 F500 ; second Part intro Line
G92 E0.0
G1 Z5 E-{retract_length[0]} F{retract_speed *60}
G1 X{first_layer_print_min[0]} Y{first_layer_print_min[1]} Z{first_layer_height} F30000
G1 E{retract_length[0]} F{retract_speed*60}
G92 E0.0

                                      I do not use a mesh.g this does not exists on my system
                                      my bed.g:

                                      ; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v2.1.8 on Sun Feb 09 2020 01:08:02 GMT+0100 (Mitteleuropäische Normalzeit)
M561 ; clear any bed transform
G4 P100
G28 ; home
G0 Z10 F4200

G0 F60000
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G30 P0 X5 Y155 Z-99999						;Orbiter
G30 P1 X302 Y155 Z-99999 S2					;Orbiter
G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G0 X45 Y-5 F60000
G29 										;Probe the heatbed and generate heightmap

G91 										;Relative positioning
G1 Z5 F1500 								;Raise Z 5mm
G90 										;Absolute positioning

G4 P100
G0 X0 Y0 F60000 						;Go to Parking Position

                                      some settings in config.g that maybe relevant for:

                                      ...
M671 X-52:377 Y155:155 S2.5 					   ; leadscrews at left (connected to Z) and right
...
M557 X10:300 Y10:300 P6:6; S40                     ; define mesh grid ( the normal full size mesh config)

                                      what can I do with this start code so that it is probing in mesh like A5 in normal mesh?
                                      Best off five ?

                                      danym21undefined 1 Reply Last reply Reply Quote 0
                                      • danym21undefined
                                        danym21 @Proschi3D
                                        last edited by

                                        @Proschi78 said in Only probe where the part will be printed:

                                        ke A5 in no

                                        the A5 needs to be in the config.g where you configure the probe type
                                        look for M558
                                        https://docs.duet3d.com/User_manual/Reference/Gcodes#m558-set-z-probe-type

                                        Proschi3Dundefined 1 Reply Last reply Reply Quote 0
                                        • Proschi3Dundefined
                                          Proschi3D @danym21
                                          last edited by Proschi3D

                                          @danym21
                                          Hello,
                                          I know that and I also have it in the config.g
                                          but if I start a print and it only creates the mesh where the printed part is, then it only runs once in z

                                          M558 P1 C"io3.in" H5 A5 S0.009 F150 T6000                           ; set Z probe type to unmodulated and the dive height + speeds
G31 P500 X0 Y0 Z1.730; set Z probe trigger value, offset and trigger height
M557 X30:330 Y-3:210 P9
                                          danym21undefined 1 Reply Last reply Reply Quote 0
                                          • danym21undefined
                                            danym21 @Proschi3D
                                            last edited by

                                            @Proschi78
                                            mhm, this makes no sense for me, do you have a M558 on some other positions? like in the the bed.g or config-override.g?

                                            I will test this when I have time for, I normaly use only one probe per point.

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA