Duet wifi S3D

schneik80

here is a script that works for me:

[[language]]
path=[output_filepath]
file=${path##*/}
curl -# -d "@[output_filepath]" -X POST http://xxx.xxx.xxx.xxx/rr_upload?name=gcodes/$file

schneik80

On OSX i have a folder action using a bash script

[[language]]
for f in "$@"
do
	path="$f"
	file=${path##*/}
	curl -# -d "@$f" -X POST http://xxx.xxx.xxx.xxx/rr_upload?name=gcodes/$file
done

Any gcode file I save to this folder with the action gets uploaded. I like this better than the s3d terminal option because the upload happens on save, not preview on print. In this way i only upload once when i know the print looks right.

FrankNPrinter

Just my 2 cents and might be off topic but if using usb, you might want to modify a cable and cut out the 5V supply especially if you have a dedicated 5v in to the board already.

BrianHanifin

Thank you for this. I have fine tuned the code for Simplify3D a little, and it works great!

curl -d "@[output_filepath]" -X POST http://hypercube.local/rr_upload?name=gcodes/[output_filename].gcode

BrianHanifin

OK. While the above code does upload a file to duet, it does something to the file that leaves it unprintable. I have experimented with it and discovered the following works. This may not be the optimal method still, but it does yield a printable GCode file.

curl  -F "file=@[output_filepath]" "http://hypercube.local/rr_upload?name=gcodes/[output_filename].gcode"

The reason I say it is not optimal is that is places some HTTP data at the top of the file. But, Duet appears to ignore this code and happily prints anyway. So, for now it will do.

--------------------------16eea21da68ae83e
Content-Disposition: form-data; name="file"; filename="curl_test.gcode"
Content-Type: application/octet-stream

Alex9779

This is great! thumbsup Thanks for sharing…

sungod3k

Hi,

I used a similar command with Octoprint succesfully so I was quite happy when I found this thread.

The command Im using is
curl -# -d "@[output_filepath]" -X POST http://xxx.xxx.xxx.xxx/rr_upload?name=gcodes/[output_filename].gcode"
which uploads the code correctly, however when I want to print the autouploaded code, it starts the print, does nothing and then returns the message "print finished in 0h 1m".

The same code works normally when I upload it via the webinterface.

Whats the trick to get that working?

Cheers

MoS-tekknix

Please download the "uploaded" GCode via WebInterface and take a look into the file. Maybe there it will be clearer what happens.

sungod3k

I ran the original and the autouploaded file through notepad++s compare tool and they matched 100%

MoS-tekknix

@sungod3k:

I ran the original and the autouploaded file through notepad++s compare tool and they matched 100%

Uhm, thats interesting.

Can you try this one, i'm using and change the IP to your DuetWifi/Ethernet IP?

[[language]]
curl -F "file=@[output_filepath]" "http://192.168.178.144/rr_upload?name=gcodes/[output_filename].gcode"

That is working even if the Printer is currently busy.

Regards
MoS-tekknix

sungod3k

Great, that seems to work. Thanks

MoS-tekknix

@sungod3k:

Great, that seems to work. Thanks

You're welcome. That's what's a forum for

Regards
MoS-tekknix

tychop

@MoS-tekknix:

@sungod3k:

I ran the original and the autouploaded file through notepad++s compare tool and they matched 100%

Uhm, thats interesting.

Can you try this one, i'm using and change the IP to your DuetWifi/Ethernet IP?
[[language]]
curl -F "file=@[output_filepath]" "http://192.168.178.144/rr_upload?name=gcodes/[output_filename].gcode"
That is working even if the Printer is currently busy.

Regards
MoS-tekknix

This script
curl -F "file=@[output_filepath]" "http://192.168.x.x/rr_upload?name=gcodes/[output_filename].gcode"
uploads the file correctly, but the print doesn't start…

Am I missing something?

dc42

You need to send a separate command to print the file.

tychop

Yes, I figured that could be the issue, however, I couldn't find anything here https://github.com/chrishamm/DuetWebControl…

Is there a command to print? Where can I look for it?

I can see

[[language]]
function startUpload(type, files, fromCallback) {

```in the javascript, but am clueless how to specify 'print' as the type to upload gcode & start the print

dc42

Use the rr_gcode command to send M32 "filename.gcode".

tychop

Yep, Got it

This works:
curl -F "file=@[output_filepath]" "http://192.168.x.x/rr_upload?name=0%3A%2Fgcodes%2F[output_filename].gcode"
curl "http://192.168.x.x/rr_gcode?gcode=M32 0%3A%2Fgcodes%2F[output_filename].gcode"

Many thanks !!

dc42

You will need to enclose the filename in double quotes when sending it if you want it to work on filenames with ( or ) or ; in the name.

SEUTec

Hi all:

curl –data-binary "@[output_filepath]" "http://192.168.x.x/rr_upload?name=gcodes/[output_filename].gcode"

–data-binary don't losse the NewLine or CarriageReturns as -d do.
and don't add extra data to the gcode file as -F do.

Regards.

kuhnikuehnast

The best that worked for me is:

curl --data-binary "@[output_filepath]" "http://192.168..XX.XX/rr_upload?name=gcodes%2F[output_filename].gcode"

curl "http://192.168.XX.XX/rr_gcode?gcode=M32 [output_filename].gcode"

But there are still some problems...

If you have a Space in the name, the file is only saved as the first part til the space (e.g. Test file.gcode is saved as Test.gcode)
Special Characters (e.g. äöü) aren't saved properly
Is there a possibility to delete the file on the local computer after uploading it to the duet? Couldn't find any solution...

greetings kuhni