Warning: M500: No M501 command was executed in config.g
-
I am trying to calibrate the home height on my Mini Kossel delta with a duet 2 Ethernet and Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta3 (2021-08-24) .
It was working fine then all of a sudden it hit the bed when starting a print.
I have been going through the dozuki for doing this (which I've done before) up to setting the Z=0 and probe trigger height, but when I send M500 to save the values it comes back with the message "Warning: M500: No M501 command was executed in config.g" even though there is one there. Tried rebooting power cycling on/off still the same.
When I test H height again it is wrong again.
Am I missing something? -
@dave-parry said in Warning: M500: No M501 command was executed in config.g:
"Warning: M500: No M501 command was executed in config.g" even though there is one there.
Can you please provide the results of M122 and M98 P"config.g" and post your config.g?
-
M122=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.0beta3 (2021-08-24 13:56:10) running on Duet Ethernet 1.02 or later
Board ID: 0JD0M-9P6M2-NWNS4-7J1DA-3SJ6M-TA2ZK
Used output buffers: 3 of 24 (22 max)
=== RTOS ===
Static ram: 23940
Dynamic ram: 69944 of which 0 recycled
Never used RAM 18196, free system stack 190 words
Tasks: NETWORK(ready,26.4%,247) HEAT(notifyWait,0.0%,310) Move(notifyWait,0.0%,364) MAIN(running,73.4%,445) IDLE(ready,0.2%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:00:45 ago, cause: software
Last software reset at 2021-09-11 12:12, reason: User, GCodes spinning, available RAM 18196, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 40.1, current 40.5, max 40.8
Supply voltage: min 24.1, current 24.2, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 34640, standstill, SG min/max not available
Driver 1: position 34640, standstill, SG min/max not available
Driver 2: position 34640, standstill, SG min/max not available
Driver 3: position 0, standstill, SG min/max not available
Driver 4: position 0, standstill, SG min/max not available
Driver 5: position 0
Driver 6: position 0
Driver 7: position 0
Driver 8: position 0
Driver 9: position 0
Driver 10: position 0
Driver 11: position 0
Date/time: 2021-09-11 12:13:03
Cache data hit count 1743212367
Slowest loop: 10.26ms; fastest: 0.16ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.2ms, write time 2.8ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 31.65ms; fastest: 0.04ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplexM98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled
Error: No power fail script provided
Error: G0/G1: insufficient axes homed; Configuration file for Duet 0.8.5 (firmware version 1.21)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.2 on Thu Sep 02 2021 19:22:19 GMT+0100 (British Summer Time); General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"MiniKossel" ; set printer name
M665 R105.6 L217.29 B85 H243.1 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X-26.2 Y-26.2 Z-26.4 ; put your endstop adjustments here, or let auto calibration find them; Network
M540 PBE:XX:XX:XX:XX:XX ; set custom MAC address
M552 P192.X.X.XX S1 ; enable network and set IP address
M553 P255.255.255.0 ; set netmask
M554 P192.X.X.X ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M92 X80.00 Y80.00 Z80.00 E683.5 ; set steps per mm
M566 X1200.00 Y1200.00 Z1200.00 E1200.00 ; set maximum instantaneous speed changes (mm/min)
M203 X20000.00 Y20000.00 Z20000.00 E3600.00 ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z1000.00 E1000.00 ; set accelerations (mm/s^2)
M906 X1000 Y1000 Z1000 E450 I60 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 Z-0.1 S1 ; set minimum Z; Endstops
M574 X2 S1 P"xstop" ; X min active high endstop switch
M574 Y2 S1 P"ystop" ; Y min active high endstop switch
M574 Z2 S1 P"zstop" ; Z min active high endstop switch; Z-Probe
M558 P1 C"zprobe.in" H8 F120 T2400 ; set Z probe type to switch and the dive height + speeds
G31 P500 X-0 Y-0 Z1.371; this Z offset is just above the bed, I fine tune with my Z offset routine.; Bed Mesh
M557 R130 S20 ; probe within a radius of 130mm from the centre with a mesh spacing of 20mm; Heaters
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0temp" Y"thermistor" T100000 B4388; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0heat" T1 ; heater 1 uses the e0heat pin and sensor 1
M140 P0 H0 ; map heated bed to heater 0; Fans
M950 F0 C"fan0"
M950 F1 C"fan1"
M106 P0 S0 I0 F500 H-1 C"Part Clg" ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S0 I0 F500 H-1 C"Bed Clg" ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off; Tools
M563 P0 S"Hot End" D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
; Power Failure
M911 S21.0 R23.0 G91 M83 G1 Z3 E-5 F1000"; Miscellaneous
T0 ; select first tool
M501 -
Dont know if its relevent but I just tried G29 S0 and all I get is response too long and console shows
Warning: Skipping grid point X=-80.0, Y=60.0 because Z probe cannot reach it for all points.It does save a file to card but Hieght map says invalid
-
@dave-parry heightmap invalid was a bug in version 3.2 of the DWC so you need to update the version of DWC you're running
Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is
-
This post is deleted! -
@jay_s_uk said in Warning: M500: No M501 command was executed in config.g:
@dave-parry heightmap invalid was a bug in version 3.2 of the DWC so you need to update the version of DWC you're running
Not actually a bug, it's because the height map file format was changed to support axes other than X and Y, and older DWC versions don't know about the new format.
-
Ok Updated to 3.3, but don't have time just at the mo to see if that has fixed it. Will try later this afternoon
-
I am getting a height map now. I think the warnings were for additional points on the command outside my print bed diameter. But still have the original problem.
Also get the following11/09/2021, 18:11:46 G32
Error: Auto calibration failed because probe point P0 was unreachable using the current delta parameters. Try a smaller probing radius.
11/09/2021, 18:10:34 M500
Warning: M500: No M501 command was executed in config.g -
@dave-parry said in Warning: M500: No M501 command was executed in config.g:
; Power Failure
M911 S21.0 R23.0 G91 M83 G1 Z3 E-5 F1000"You're missing a double quote mark on this line and I think that's messing up the rest of the lines after it.
Here's my line as comparison:
; POWER LOSS RECOVERY ; M911 S21 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-1 F500" ; Configure automatic saving on power loss -
Thanks for reply but still getting error message "Warning: M500: No M501 command was executed in config.g"
here's what I have at the end of config.g now; Power Failure
;
M911 S21.0 R23.0 G91 M83 G1 Z3 E-5 F1000"; Miscellaneous
T0 ; select first toolM501
-
@dave-parry said in Warning: M500: No M501 command was executed in config.g:
as @Phaedrux said, here is your mistake
M911 S21.0 R23.0 G91 M83 G1 Z3 E-5 F1000"
change this to:
M911 S21.0 R23.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" -
@siam said in Warning: M500: No M501 command was executed in config.g:
M911 S21.0 R23.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"
Thanks Slam that seems to have fixed it.
Just have to recalibrate it now.
Have to say this hasn't been as easy a transition from a legacy duet to a duet 2 has I had hoped.
Thanks to all for their help.
