CR-10S5 Firmware

DocTrucker

Struggled to find a spec for the motors are they all creality 42-40? If so do they match the resistance of the following link?

https://m.banggood.com/Creality-3D-Two-Phase-42-40-RepRap-42mm-Stepper-Motor-For-REPRAP-Makerbot-3D-Printer-p-1423026.html#popupStatedetail

If so your current settings are low. 80% of a 1.68A motor is 1.344A, not 0.8. Not likely to make the motion juttery unless the acis is stiff.

Please make sure the motor pairs are wired right to the board (different manufacturers change the cable orders) before upping the current. You may be getting away woth it at low current but you may fry your board if you up the current with the motors wired wrong.

Veti

@DocTrucker said in CR-10S5 Firmware:

Struggled to find a spec for the motors are they all creality 42-40? If so do they match the resistance of the following link?

check this
https://gist.github.com/knoopx/e6c40a009e796203b93a75a3ed6a5ab8

DocTrucker

@Veti the JK42HS42-1704 motor linked on that page is 1.7A. Looks like there is some variation on what creality strapped to their machines?

https://m.made-in-china.com/product/Jk42hs401704-NEMA-17-3D-Printer-Stepper-Motor-42mm-Reprap-Motor-729798295.html

Perhaps their board doesn't work well at higher currents?

Edit: There are 4 JK42HS40-* motors. A resistance check should confirm which it is. The 30ohm resistance is unlikely. They come in 1.7, 1.3, and 1.2A rated models.

Note for the original poster. Don't change current without confirming which motors are strapped to your machine. If in doubt, leave as is.

Gost101

All of the endstops switch to NO upon being at zero, however the endstop is not stoping the axis from wanting to move after the endstop has been triggered. They Y motor moves now perfectly, seemed to be a loose wire on the connector attached to the motor.

Phaedrux

Endstops are only active when doing a homing move with G1 S1

Gost101

Cool beans, that is the next task. I need to fix the homing functions next, as they don't move the intended motor. I'm also still having a probelm with syncing the z axis. Going down is fine, however going up will produce a stair case affect (one motor will spin while the other doesnot then the motors switch and do the same thing)

Gost101

All of the homing functions are fixed, I'm at a restaurant right now, but I will post the config and home files when I get back. Is there a way to make the z move fast on the way down, but slow on the way up?

Gost101

Home ALL homeall (1).g

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v2.0.3 on Wed Sep 11 2019 20:24:24 GMT-0600 (Mountain Daylight Time)
; Y
G91               ; relative positioning
G1 S1 Y-505 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F6000       ; go back a few mm
G1 S1 Y-505 F360  ; move slowly to Y axis endstop once more (second pass)
G90               ; absolute positioning
; X
G91               ; relative positioning
G1 S1 X-505 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000       ; go back a few mm
G1 S1 X-505 F360  ; move slowly to X axis endstop once more (second pass)
G90               ; absolute positioning
; Z
G91               ; relative positioning
M92 Z400.00      ; Move Z Fast
G1 S1 Z-505 F3000 ; move Z down until the endstop is triggered
G92 Z0            ; set Z position to axis minimum (you may want to adjust this)
G1 Z1 F6000       ; go back a few mm
M92 Z80		  ; Move Slow
G1 S1 Z-505 F400 ; move slowly to X axis endstop once more (second pass)
G90               ; absolute positioning

Home X homex.g

; homex.g
; called to home the X axis
;
; generated by RepRapFirmware Configuration Tool v2.0.3 on Wed Sep 11 2019 20:24:24 GMT-0600 (Mountain Daylight Time)
G91               ; relative positioning
G1 S1 X-505 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000       ; go back a few mm
G1 S1 X-505 F360  ; move slowly to X axis endstop once more (second pass)
G90               ; absolute positioning

Home Y homey.g

; homey.g
; called to home the Y axis
;
; generated by RepRapFirmware Configuration Tool v2.0.3 on Wed Sep 11 2019 20:24:24 GMT-0600 (Mountain Daylight Time)
G91               ; relative positioning
G1 S1 Y-505 F1800 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F6000       ; go back a few mm
G1 S1 Y-505 F360  ; move slowly to Y axis endstop once more (second pass)
G90               ; absolute positioning

Home Z homez (1).g

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v2.0.3 on Wed Sep 11 2019 20:24:24 GMT-0600 (Mountain Daylight Time)
G91               ; relative positioning
M92 Z400.00      ; Move Z Fast
G1 S1 Z-505 F3000 ; move Z down until the endstop is triggered
G92 Z0            ; set Z position to axis minimum (you may want to adjust this)
G1 Z1 F6000       ; go back a few mm
M92 Z80		  ; Move Slow
G1 S1 Z-505 F400 ; move slowly to X axis endstop once more (second pass)
G90               ; absolute positioning

Gost101

I just got my BLTouch in today, but I will have to print out the mount once this can print.

What I have to do next:

Either figure out:

Why my hot end thermister is not working.
-Possibly rewire
Why my hotend will not heat up.
-Possibly rewire
-Wait for the new one to arrive: Here
Figure out how to use a filament sensor
Replace Main Hotend fan for a Noctua fan: Here

Phaedrux

@Gost101 said in CR-10S5 Firmware:

M92 Z400.00 ; Move Z Fast
M92 Z80 ; Move Slow

Nope, this isn't right. You're changing the steps per mm value for the axis, which isn't changing the speed it's changing how far it's moving per rotation. Not sure what the intention is there.

Phaedrux

@Gost101 said in CR-10S5 Firmware:

I just got my BLTouch in today, but I will have to print out the mount once this can print.

When you switch to a z probe you can follow the guidance here for setting up the probe and the Z homing macro:

https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter#Section_Homing_Z_using_a_Z_probe

https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch

Gost101

Is there a way to make the axis move faster besides changing the steps/mm?

Phaedrux

Change the feed rate of the move.

Gost101

Which command is that?

Phaedrux

That's the F parameter of the G1 moves

Gost101

Here is the latest config files.
I need to print the BLTouch mount before I can begin using it.
Everything heats up, however I'm having trouble with the e3D Volcano extruding (I just bough a Bondtech Extruder to hopeful solve this as the stock extruder is skipping. I will try to see if the hotend is clogged, I don't think it is due to being a e3D nozzle X.
Everything works at the moment, so I will attempt a benchy.

Config.g: config.g

;config.g
; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
; Contact gost1017@gmail.com for more help.

; General preferences
G90                                      ; send absolute coordinates...
M83                                      ; ...but relative extruder moves
M550 P"A.C.E."                           ; set printer name
M669 K0                                  ; select Cartesian mode

; Network
M551 P"12345"                            ; set password
M552 S1                                  ; enable network
M586 P0 S1                               ; enable HTTP
M586 P1 S0                               ; disable FTP
M586 P2 S0                               ; disable Telnet

; Drives
M569 P0 S1                               ; X physical drive 0 goes forwards
M569 P1 S1                               ; Y physical drive 1 goes forwards
M569 P2 S0                               ; Z physical drive 2 goes backwards
M569 P2 S0                               ; Z physical drive 2 goes backwards
M569 P3 S1                               ; E physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                         ; set drive mapping
M350 X16 Y16 Z16 E16 I1                  ; configure microstepping with interpolation
M92 X80.00 Y78.00 Z400.00 E420.00        ; set steps per mm
M566 X900.00 Y900.00 Z1400.00 E120.00    ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z1400.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z1400.00 E250.00    ; set accelerations (mm/s^2)
M906 X800 Y800 Z8000 E800 I30            ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                  ; Set idle timeout

; Axis Limits
M208 X0:500 Y0:500 Z0:500                ; set axis maxima

; Endstops
M574 X1 Y1 Z1 S1                         ; set active high endstops

; Z-Probe
M558 P0 H5 F120 T6000                    ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                 ; define mesh grid

; Heaters
M305 P0 T100000 B4138 R4700              ; set thermistor + ADC parameters for heater 0
M143 H0 S120                             ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4138 R4700              ; set thermistor + ADC parameters for heater 1
M143 H1 S280                             ; set temperature limit for heater 1 to 280C

; Fans
M106 P0 S0 I0 F500 H-1                   ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                         ; define tool 0
G10 P0 X0 Y0 Z0                          ; set tool 0 axis offsets
G10 P0 R0 S0                             ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

Home All: homeall.g

; homeall.g
; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 (6:00PM for Civs). 
; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
; Contact gost1017@gmail.com for more help.
; Y-Axis
G91                ; relative positioning
G1 S1 Y-505 F3000  ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F1000        ; go back a few mm
G1 S1 Y-505 F360   ; move slowly to Y axis endstop once more (second pass)
G90                ; absolute positioning
; X-Axis
G91                ; relative positioning
G1 S1 X-505 F1800  ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000        ; go back a few mm
G1 S1 X-505 F360   ; move slowly to X axis endstop once more (second pass)
G90                ; absolute positioning
; Z-Axis
G91                ; relative positioning
G1 S1 Z-505 F10000 ; move Z down until the endstop is triggered
G92 Z0             ; set Z position to axis minimum (you may want to adjust this)
G1 Z3 F800         ; go back a few mm
G1 S1 Z-505 F80    ; move slowly to X axis endstop once more (second pass)
G90                ; absolute positioning

Home X: homex.g

; homex.g
; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
; Contact gost1017@gmail.com for more help.
G91               ; relative positioning
G1 S1 X-505 F1800 ; move quickly to X axis endstop and stop there (first pass)
G1 X5 F6000       ; go back a few mm
G1 S1 X-505 F360  ; move slowly to X axis endstop once more (second pass)
G90               ; absolute positioning

Home Y: homey.g

; homey.g
; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
; Contact gost1017@gmail.com for more help.
G91               ; relative positioning
G1 S1 Y-505 F3000 ; move quickly to Y axis endstop and stop there (first pass)
G1 Y5 F1000       ; go back a few mm
G1 S1 Y-505 F360  ; move slowly to Y axis endstop once more (second pass)
G90               ; absolute positioning

Home Z: homez.g

; homez.g
; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 MST (6:00PM for Civs). 
; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr10s5-firmware/37
; Contact gost1017@gmail.com for more help.
G91                  ; relative positioning
G1 S1 Z-505 F10000   ; move Z down until the endstop is triggered
G92 Z0               ; set Z position to axis minimum (you may want to adjust this)
G1 Z3 F800           ; go back a few mm
G1 S1 Z-505 F80      ; move slowly to X axis endstop once more (second pass)
G90                  ; absolute positioning
; Uncomment the following lines to lift Z after probing
;G91                 ; relative positioning
;G1 S2 Z5 F100       ; lift Z relative to current position
;G90                 ; absolute positioning

JamesM

Your thermistor settings are wrong for both your bed and hotend.....The bed should be M305 P0 T100000 B3950 R4700 and the volcano if it has the E3D cartridge thermistor should be M305 P1 T100000 B4725 C7.060000e-8 R4700

Gost101

Thanks, I changed that before this print: ![alt text]

Gost101

I've got a lot of tweaking to do.

Phaedrux

It's not... THAT bad... I guess.