Cheers, much appreciated.

Great! When you do find a nice config that works well, feel free to share. 😀

@deckingman

Another good source for free music ( some a great as soundtrack)
Machinimasound

@bellwether said in Simplify3d firmware configuration file:

What about controlling part cooling fans?

By default, Simplify3D will use M106, which Duet accepts. So everything under the "cooling" tab "just works"

Do you need it to do something else?

oh, i was thinking more of something like this:

https://solarbotics.com/product/13150/?cid=2&gclid=Cj0KCQjw5-TXBRCHARIsANLixNzBK7SDLEOZA82uLS-AnZXPUH5HKEOBw05I709rEW5My8G8SXPppbkaAufbEALw_wcB

Forget it..... Solved.

I haved select by default a 2,85 diameter material....

File tfree1.g will be called when tool 1 is freed, tpre1.g will be called just before tool 1 is activated, and tpost1.g will be called just after tool 1 has been activated. Similarly for any other tool numbers you create.

@giuseppe said in Problema di configurazione wifi:

perfetto risolto!!!!
Grazie a tutti

Sadly I don't understand Italian (just some French and German and a few words of Dutch, Spanish and Hungarian), but I think the jist is that it is working now.

Very cool, any prints from it?

Until you have a Z probe, you can set the Z probe type to 0 in the M558 command (M558 P0). Then you can run delta calibration as normal (see https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer)) and the web interface will prompt you. If you just want to establish an accurate Z=0 height before printing, position the nozzle over the centre of the bed and send G30.

HTH David

@dc42:

There's a good case to be made for electronics at the top and PSU at the bottom. It keeps all the mains voltage wiring out of the way when you are messing around with the electronics, and saves running mains voltage wires up to the top.

Agreed, that is a nice balance.

And/or split the difference. I do have PSU on top on this particular printer, and therefore mains wiring… at the same time, this will have a heated bed, with the heater using mains wiring, and that will be via a SSR and separate mains plug, all at the bottom. So a little of each.

In any event, ALWAYS earth (ground for Yanks) the frame on an all-metal printer.

I dont use mesh bed leveling (G29), I only do the calibration (G32) because my bed is leveled (I removed the springs and replaced them with TPU feet).
M671 indicates the location of my Z leadscrews when my bed is located at 0,0 and they are slightly off-center:

M671 X-55:255 Y170:170 S1.5 // one leadscrew is located at -55,170, other leadscrew is located at 255,170 ```In fact, the Y coordinates for 2 point leveling don't really matter as long as they are the same The probing points are defined in bed.g:

G28 ; home
G30 P0 X40 Y150 Z-99999 ; probe near a leadscrew
G30 P1 X160 Y150 Z-99999 S2 ; probe near a leadscrew and calibrate 2 motors
G28 Z

Nope .
this is the origianl Italian thread created by Fabrizo ( eagle 26).
he is available for sharing all his work.
http://forums.reprap.org/read.php?362,768409,789866#msg-789866

@watchimgo:

If anyone is looking for a Rostock Max V3 that has already been upgraded with a Duet Wifi controller and many other upgrades, you can find one right now on ebay: http://www.ebay.com/itm/-/142502541362?

Anyone know where that panelduo encasing is available? Can we share the stl?

Nice machine! love the sound the machine made while traveling.