Wow thanks guys i am testing some settings. But i must say great support from you guys. I love the duetWifi its nice and much nicer to change settings then Marling with the ramps board.
Thanks for the help
Latest posts made by CobraMike
-
RE: Weird effect while printingposted in Tuning and tweaking
-
Weird effect while printingposted in Tuning and tweaking
Ok thanks to a moderator or admin here. I found out that my z motors was outer sinc. Bit after 2 test prints i am stuck. I dont now how to solve this. Can some one help me.
Motor / Jerk settings.
[[language]] ; Drives M569 P0 S1 ; Drive 0 goes forwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes backwards M350 X16 Y16 Z16 E16 I0 ; Configure microstepping without interpolation M92 X80 Y80 Z400 E150 ; Set steps per mm M566 X1200 Y1200 Z24 E300 ; Set maximum instantaneous speed changes (mm/min) M203 X30000 Y30000 Z600 E3000 ; Set maximum speeds (mm/min) M201 X500 Y500 Z100 E5000 ; Set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; Set axis minima M208 X250 Y210 Z180 S0 ; Set axis maximaAnd here my printer with bountech ectruder. Love this extruder
-
RE: Bed Leveling wrongposted in Tuning and tweaking
Can you explain what you think is wrong with that height map? It looks to me that you have something like an i3 setup with dual Z motors, and the Z motors have become out of sync. Also either the Z homing position or the Z probe trigger height is not set accurately.
That help me. Its not working. My z motos was outer sync. My print looks amazing.
-
Bed Leveling wrongposted in Tuning and tweaking
Ok I love the duet3d simple to configure. And the community is great i read aloud here of fixed. But now i need the help of you guys again. I am stuck @ the moment with my build.
I have a MK42 clone bed
I use the original Pinda probeBut every time i use G29 or G32 my bed is weird. I show the CVS of my bed also and my config. Can someone here please help me what do i do wrong.
heightmap.csv
[[language]] RepRapFirmware height map file v2 generated at 2018-02-08 21:52, mean error -0.718, deviation 0.373 xmin,xmax,ymin,ymax,radius,xspacing,yspacing,xnum,ynum 25.00,235.00,25.00,195.00,-1.00,20.00,20.00,11,9 -0.003, 0.013, 0.007, -0.020, -0.722, -0.967, -1.110, -0.893, -0.523, -0.643, -0.790 -0.003, 0.015, -0.567, -0.592, -0.665, -0.740, -1.055, -1.163, -1.283, -0.645, -0.810 0.007, 0.005, -0.567, -0.577, -0.638, -0.753, -0.893, -1.062, -1.245, -1.457, -0.805 -0.010, -0.575, -0.558, -0.590, -0.645, -0.712, -0.888, -1.045, -1.183, -1.535, -0.805 -0.020, -0.592, -0.572, -0.505, -0.587, -0.648, -0.855, -0.995, -1.155, -1.457, -0.938 -0.158, -0.597, -0.592, -0.548, -0.577, -0.640, -0.820, -0.960, -1.235, -1.462, -1.033 -0.165, -0.622, -0.595, -0.622, -0.660, -0.707, -0.788, -0.962, -1.085, -1.367, -0.862 -0.193, -0.155, -0.643, -0.640, -0.668, -0.725, -0.842, -0.995, -1.138, -1.327, -0.830 -0.213, -0.207, -0.665, -0.675, -0.717, -0.742, -0.942, -1.043, -1.153, -0.670, -0.790My config.g
[[language]] ; Configuration file for Duet WiFi (firmware version 1.20 or newer) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool on Thu Mar 08 2018 21:43:26 GMT+0100 (West-Europa (standaardtijd)) ; General preferences G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 PCobraWorld ; Set machine name M551 P******* ; Set password M552 S1 ; Enable network M587 S"********" P"********" I192.168.1.16 J192.168.1.254 K255.255.255.0 ; Configure access point and IP addresses. You can delete this line once connected M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S1 ; Drive 0 goes forwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S1 ; Drive 3 goes forwards M350 X16 Y16 Z16 E256 I0 ; Configure microstepping without interpolation M92 X80 Y80 Z400 E420 ; Set steps per mm M566 X900 Y900 Z12 E120 ; Set maximum instantaneous speed changes (mm/min) M203 X30000 Y30000 Z300 E1200 ; Set maximum speeds (mm/min) M201 X500 Y500 Z250 E250 ; Set accelerations (mm/s^2) M906 X830 Y830 Z830 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; Set axis minima M208 X250 Y210 Z180 S0 ; Set axis maxima ; Endstops M574 X1 Y1 S0 ; Set active high endstops ; Z-Probe M574 Z1 S2 ; Set endstops controlled by probe M558 P1 H5 F120 T12000 ; Set Z probe type to unmodulated and the dive height + speeds G31 P500 X23 Y9 Z2.5 ; Set Z probe trigger value, offset and trigger height M557 X25:235 Y25:195 S20 ; Define mesh grid ; Heaters M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning) M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S1 I0 F500 H T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P1 S1 I0 F500 H-1 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P2 S1 I0 F500 H-1 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned off ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Automatic saving after power loss is not enabled ; Custom settings are not configured -
RE: Configuration Files for P3steel or Prusaposted in Example setups and prints
I have a p3 steel with titan aero extruder with 0.9deg E3d pancake motor, 1.8deg motors on all axis.
I use 2 motors on the Z axis (second motor is driven by E1 driver) and use 2 motor auto leveling feature
I use a precision piezo board as probe (piezo is mounted on the carriage).; Prusa i3 config file for dc42 Duet firmware ; Prologue and comms section M111 S0 ; Debug off M550 PKryo_Prusai3_001 ; Machine name (can be anything you like) M551 <redacted>; Machine password ; Wifi Networking ;M552 S0 M552 S1 ; Enable WiFi M586 P0 S1 R20000 ; Set Port 20000 for HTTP ; General M555 P2 ; Set output to look like Marlin ;M575 P1 B57600 S1 ; Comms parameters for PanelDue ; Movement section M569 P0 S0 ; Drive 0 goes backwards M569 P1 S1 ; Drive 1 goes forwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes backwards M569 P4 S1 ; Drive 4 goes forwards M574 X1 Y1 Z0 S0 ; set endstop configuration (X and Y endstops only, at low end, active high) M584 X0 Y1 Z2:4 ; X uses driver 0, Y driver 1, Z drivers 2 and 4 M906 X1500 Y1500 Z1000:1000 E1250 ; Set motor currents (mA) M201 X2000 Y2000 Z100 E1000 ; Accelerations (mm/s^2) M203 X15000 Y15000 Z800:800 E1800 ; Maximum speeds (mm/min) M566 X1200 Y1200 Z800:800 E300 ; Set allowable instantaneous speed change mm/min M208 X200 Y298 Z150 ; set axis maxima (adjust to suit your machine) M208 X-20 Y-8 Z0 S1 ; set axis minimum (adjust to make X=0 and Y=0 the edge of the bed) M84 S30 ; Set idle timeout M350 X16 Y16 Z16:16 E16 I1 ; Set 16x microstepping with interpolation M92 X80 Y80 Z400:400 ; Set axis steps/mm M92 E837 ; Set extruder steps per mm G21 ; Work in millimetres G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves M572 D0 S0.05 ; pressure advance M207 S1.2 R0 F3000 ; firmware retraction M929 P"eventlog.txt" S1 ; enable eventlogging ; Z probe section M558 P8 X0 Y0 Z1 H20 I0 R1 F600 T2000 ; Piezo probe used for homing Z axis, dive height 2cm, probe speed 600mm/min, travel speed 2400mm/min G31 X0 Y0 Z-0.14 P600 ; Set the probe height and threshold (put your own values here) ;M557 X1:180 Y1:290 S30 : Set probe grid M671 X-55:255 Y170:170 S1.5 ; leadscrews for G32 ; Heater and thermistor section ;*** If you have a Duet board with 1K thermistor series resistors, change R4700 to R1000 to the following M305 commands M305 P0 R4700 T100000 B3950 ; Put your own H and/or L values here to set the bed thermistor ADC correction M305 P1 R4700 T100000 B4725 ;7.06e-8 ; Put your own H and/or L values here to set the first nozzle thermistor ADC correction M305 P2 R4700 H0 L0 ; Put your own H and/or L values here to set the second nozzle thermistor ADC correction M301 H1 P10 I0.10 D100 T0.50 S1.0 ; PID settings for extruder 0 ;M301 H2 P10 I0.10 D100 T0.50 S1.0 ; PID settings for extruder 1 ;M307 H1 A391.6 C185.2 D4.0 S1.00 B0 ; PID Tuning Extruder 0 // E3DV6 clone ;M307 H1 A380 C175.0 D6.5 S1.00 B0 ; PID Tuning Extruder 0 // new E3DV6 M307 H1 A349.1 C187.2 D6.5 S1.00 B0 ;M570 S120 ; Increase to allow extra heating time if needed M106 P1 T45 H1 ; Cooling fan for Heatbreak is located on PWM 1, start blowing from 45° M106 P2 F25000 I1 ; PWM fan for HEPA filter, intel spec 25KHz inverted M143 H0 S125 ; set the maximum bed temperature to 125C M143 H1 S275 ; set the maximum temperature of the hot-end to 275°C ; Tool definition section M563 P0 D0 H1 ; Define tool 0 to use extruder drive 0 and heater 1 and FAN 0 G10 P0 S0 R0 ; Set tool 0 operating and standby temperatures ;*** If you have a dual-nozzle build, un-comment the following 2 lines ;M563 P1 D1 H2 ; Define tool 1 ;G10 P1 S0 R0 ; Set tool 1 operating and standby temperatures ; Epilogue T0 ; select first hot end</redacted>If i may ask how dit you mount the piezo do you have a foto. And thanks for the config. Ill try this one and tune on this one. Also for the bed leveling i need to find out how.
-
Configuration Files for P3steel or Prusaposted in Example setups and prints
Ok first off all i am new to the duet3d. And i now i to work with marlin but is someone has configuration files for the p3steel of prusa mk2s like printers please share that. Thanks..