@t3p3tony I did not as it ran for a fairly long time. If there's a way to get sample logs out of it I'd be happy to run it again and provide data.

@tinfish340 sorry for the delay in getting a reply. What was the issue in the end?

@sputnikoc3d adding T0 to config.g should be safe if the G10 for T0 has S0, R0 (i.e. set it to 0 temperature). what did you have in config.g?

@nightlonk42 - No Caribou / Zaribo bedslinger

A value of about 30 seems to work just fine.

@toratora72 what duet are you using paneldue with?
To use the onboard SD card you need to use the 10pin cable

@vladimir_u I've added Cyrillic support on the 12864 to the work list.

@gloomyandy i tried your suggested steps and here is the result :

Boot duet and sbc Turn on heater from dwc panel The fan don't turn on I turn off the heater wait for the temperature to go under 70°C hit emergency stop turn on heater fan don't turn on emergency stop (heater hot) fan turn on wait for the temperature to go under 70°C fan turn off Turn heater on Fan don't turn on

Here's the output of the M122 command :

=== Diagnostics === RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (SBC mode) Board ID: 08DJM-956L2-G43S8-6JTD6-3SS6K-KA1AH Used output buffers: 1 of 40 (14 max) === RTOS === Static ram: 150904 Dynamic ram: 62348 of which 0 recycled Never used RAM 140940, free system stack 202 words Tasks: SBC(ready,5.0%,330) HEAT(delaying,0.0%,325) Move(notifyWait,0.0%,302) CanReceiv(notifyWait,0.0%,908) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,7.1%,93) MAIN(running,87.7%,1250) IDLE(ready,0.1%,29), total 100.0% Owned mutexes: HTTP(MAIN) === Platform === Last reset 00:01:43 ago, cause: power up Last software reset at 2021-09-29 11:43, reason: StuckInSpinLoop, GCodes spinning, available RAM 143016, slot 2 Software reset code 0x4083 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0040080f BFAR 0x00000000 SP 0x2041970c Task IDLE Freestk 43 ok Stack: 00479e85 0047a862 61000000 a5a5a5a5 00479e85 a5a5a5a5 a5a5a5a5 2041ad9c 0000aaea 20432ac4 20424c74 20419728 20424c6c 00000004 2042cda0 2042cda0 20419728 00000000 00000001 20419784 4e49414d 00000000 00000000 00000001 00000001 00eec918 00000000 Error status: 0x00 Step timer max interval 154 MCU temperature: min 35.8, current 36.5, max 47.7 Supply voltage: min 24.3, current 24.4, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes 12V rail voltage: min 12.0, current 12.0, max 12.0, under voltage events: 0 Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0 Driver 0: position 0, standstill, reads 53339, writes 15 timeouts 0, SG min/max 0/0 Driver 1: position 0, standstill, reads 53339, writes 15 timeouts 0, SG min/max 0/0 Driver 2: position 0, standstill, reads 53339, writes 15 timeouts 0, SG min/max 0/0 Driver 3: position 0, standstill, reads 53340, writes 15 timeouts 0, SG min/max 0/0 Driver 4: position 0, standstill, reads 53340, writes 15 timeouts 0, SG min/max 0/0 Driver 5: position 0, standstill, reads 53341, writes 14 timeouts 0, SG min/max 0/0 Date/time: 2021-09-29 11:52:03 Slowest loop: 0.46ms; fastest: 0.04ms === Storage === Free file entries: 10 SD card 0 not detected, interface speed: 37.5MBytes/sec SD card longest read time 0.0ms, write time 0.0ms, max retries 0 === Move === DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000 === MainDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === AuxDDARing === Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1 === Heat === Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 1 -1 -1 -1 === GCodes === Segments left: 0 Movement lock held by null HTTP* is doing "M122" in state(s) 0 Telnet is idle in state(s) 0 File is idle in state(s) 0 USB is idle in state(s) 0 Aux is idle in state(s) 0 Trigger* is idle in state(s) 0 Queue is idle in state(s) 0 LCD is idle in state(s) 0 SBC is idle in state(s) 0 Daemon is idle in state(s) 0 Aux2 is idle in state(s) 0 Autopause is idle in state(s) 0 Code queue is empty. === CAN === Messages queued 844, received 8, lost 0, longest wait 1ms for reply type 6018, peak Tx sync delay 607, free buffers 49 (min 48), ts 517/516/0 Tx timeouts 0,0,0,0,0,0 === SBC interface === State: 4, failed transfers: 1, checksum errors: 0 Last transfer: 1ms ago RX/TX seq numbers: 2731/2870 SPI underruns 0, overruns 0 Disconnects: 1, timeouts: 0, IAP RAM available 0x2c810 Buffer RX/TX: 0/0-0 === Duet Control Server === Duet Control Server v3.3.0 Code buffer space: 4096 Configured SPI speed: 8000000Hz Full transfers per second: 15.42, max wait times: 4.7ms/0.0ms Codes per second: 0.01 Maximum length of RX/TX data transfers: 3579/64

@thechainring From the wiki
Connect the laser GND, 5V and PWM wires to the appropriate pins on the Duet 3. The 3-pin 5V PWM output on the Duet 3 Mainboard is behind the MicroSD card holder. Connect the PWM wire to the 'out9' pin.
undefined

I'm not sure whether the Duet is providing enough current via the onboard 12V. Probably best to just use the Duet to control PWM and get your power from the external adapter

It's often the little things that make life difficult: My extruder didn't make a sound on the 1LC and, as is always the case, you first check the crimp connections, the cables, the correct connections, the configuration - and everything several times. One is almost inclined to rebuild everything again, then one reads the last of countless articles and realizes that it was only a small parameter... Like above with the fan.

Kind regards, Pierre

Solved, old version of DWC (3.2 not 3.4) , DOH!

@dc42

Thank you for the response.

I have changed minZ to -2
What is "segmentation"?

David

@dc42
thank you for the response,

how do i make sure the reprap firmware is configured for the paneldue.

In my config i included this command for the panel due

M575 P1 B57600 S1

Also how do i configure the RRF to run in access point mode?

@mrehorstdmd
Get well soon!
I'd simply add the macro call to config-override. And put M501 in config.g as usual.

@chrishamm Duet 3 MB6HC, 8756ae84-50b6-4510-9ab1-7ccda1d2163d-obraz.png

And I have found part of uploaded file thas is corrupted... seems some issue with uploading? Looks like part of HTTP header found it's way to became part of file 🙂

;WIPE_START G1 F8640.000 G1 X123.480 Y109.004 E-0.10336 G1 X123.276 Y108.556 E-0.11374 G1 X123.884 Y108.812 E-0.15251 ;WIPE_END G1 E-0.430.204 User-Agent: Mozilla/5.0 (Windows NT 10.0; Win64; x64; rv:92.0) Gecko/20100101 Firefox/92.0 Accept: */* Accept-Language: pl,en-US;q=0.7,en;q=0.3 Accept-Encoding: gzip, deflate Content-Type: application/json X-Requested-With: XMLHttpRequest Connection: keep-alive Referer: http://192.168.0.204/ ؽþ 2 X121.725 Y107.215 I1.405 J-0.346 E-0.16829 ;WIPE_END G1 E-0.40387 F2100.000 G1 Z9.000 F10800.000 G1 X121.068 Y104.629 G1 Z8.600 G1 E0.80000 F2100.000 M204 S800

@dc42

Thanks for information, just to wait then 😉

@peter-matthiesen Check the fuses. Without plugging the board in, and the limited information you have provided, it's impossible to say what has gone wrong and whether it is repairable.
When you get it plugged in with power supplied, see what voltage is reported. Also post M122 response.

Ian

@pcr the heater fault detection is too sensitive in 3.4beta3. It is reduced in the forthcoming 3.4beta4.