Weirdest thing... It's back up now.
WiFi module has been up the whole time (it was responding to pings(ICMP))
Telnet to ports 23 and 80 were getting nothing
I did not connect directly to USB with my workstation and try to print.
I did put a file in the gcode directory on the SD card by hand and was able to print.
I did set up and connect an OctoPi as a possible work around and it did seem to be communicating but I had not had a chance to print with it.
I've been beating my head against my desk for the last 8 hours trying to get this sorted
and I walk away from my desk for few minutes and its back up.
I do not like issues that seem to resolve themselves in this way for obvious reasons.
It may have something to do with burning some sage and swinging a dead chicken around but.... That's dinner so it would have happened regardless.
Just for posterity:
M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.1 (2022-06-01 21:05:28) running on Duet WiFi 1.02 or later + DueX5
Board ID: 08DJM-9178L-L2MS8-6JKDA-3S06M-K8HAP
Used output buffers: 3 of 26 (26 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 76456 of which 12 recycled
Never used RAM 8248, free system stack 96 words
Tasks: NETWORK(ready,37.5%,242) HEAT(notifyWait,0.1%,324) Move(notifyWait,2.9%,292) DUEX(notifyWait,0.0%,24) MAIN(running,59.4%,460) IDLE(ready,0.1%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 01:52:37 ago, cause: power up
Last software reset at 2022-08-15 23:22, reason: User, GCodes spinning, available RAM 8608, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x0c
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 15.3, current 23.6, max 28.3
Supply voltage: min 23.9, current 24.1, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/40/40, gc cycles 0
Events: 1 queued, 1 completed
Driver 0: standstill, SG min 0
Driver 1: standstill, SG min 0
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min 0
Driver 4: standstill, SG min n/a
Driver 5: standstill, SG min 0
Driver 6: standstill, SG min 0
Driver 7: standstill, SG min 0
Driver 8: standstill, SG min n/a
Driver 9: standstill, SG min n/a
Driver 10:
Driver 11:
Date/time: 2022-08-29 15:49:42
Cache data hit count 4294967295
Slowest loop: 135.33ms; fastest: 0.17ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.9ms, write time 14.1ms, max retries 0
=== Move ===
DMs created 83, segments created 27, maxWait 3482734ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 40317, completed 40317, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Filament sensors ===
Extruder 0: pos 247.50, errs: frame 0 parity 0 ovrun 0 pol 0 ovdue 0
=== DueX ===
Read count 1, 0.01 reads/min
=== Network ===
Slowest loop: 40.98ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address 84:0d:8e:ad:74:86
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24680
WiFi IP address 192.168.1.226
WiFi signal strength -37dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 4 0 0 0 0 0 0 0
M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is enabled on port 23
Error: Heater 1 not switched on due to bad model
config.g