Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. weput
    3. Topics
    • Profile
    • Following 0
    • Followers 0
    • Topics 12
    • Posts 75
    • Best 2
    • Controversial 0
    • Groups 0

    Topics created by weput

    • weputundefined

      Network issues¿?

      Duet Hardware and wiring
      • • • weput
      6
      0
      Votes
      6
      Posts
      213
      Views

      Phaedruxundefined

      So it's working now?

    • weputundefined

      i think fan0 mosfed died.

      General Discussion
      • • • weput
      33
      0
      Votes
      33
      Posts
      1.0k
      Views

      weputundefined

      @bearer said in i think fan0 mosfed died.:

      pre heating the board helps a lot as you need less time to melt the solder and less risk of pulling a pad, but its fixed now and thats what matters in the end

      yeah.

      this board was a gift from a good friend... there is some sort of added value there...

      plus, is a good feeling this flashbacks of soldering thing... you see, i have a degree in electrical engineering; but since i moved to management i didnt touched my soldering iron in 15 years.

      had to buy a new one because the old weller broke off when i tried to change the tip.

    • weputundefined

      Error on Thermistors

      General Discussion
      • • • weput
      45
      0
      Votes
      45
      Posts
      1.8k
      Views

      weputundefined

      @bearer said in Error on Thermistors:

      good job on getting it sorted in the end!

      is hardware version 1.0 m8

    • weputundefined

      What to build.

      General Discussion
      • • • weput
      4
      0
      Votes
      4
      Posts
      560
      Views

      DjDemonDundefined

      What he said, plus what is going to excite you? I made a cylinder delta as someone suggested it could be done and now I've proved that it can be. It's not the most accurate printer but it works. Either make a machine that prints what you need to print or make something unusual and innovative.

    • weputundefined

      Fan controls

      General Discussion
      • • • weput
      4
      0
      Votes
      4
      Posts
      552
      Views

      weputundefined

      nevermind, Thermostatic control was turned on

    • weputundefined

      PT100 MAX31865 RTD-to-Digital Converter

      Duet Hardware and wiring
      • • • weput
      6
      0
      Votes
      6
      Posts
      698
      Views

      weputundefined

      Any help on how to connect it /wire it will be highly appreciated 🙂

    • weputundefined

      Filaments directory

      General Discussion
      • • • weput
      3
      0
      Votes
      3
      Posts
      574
      Views

      weputundefined

      ty man.

    • weputundefined

      1.19 from bossa port

      Firmware installation
      • • • weput
      7
      0
      Votes
      7
      Posts
      787
      Views

      weputundefined

      sorry… forgot to update

      https://www.youtube.com/watch?v=Kh7J2sSfA38

    • weputundefined

      M572 settings

      Tuning and tweaking
      • • • weput
      4
      0
      Votes
      4
      Posts
      1.2k
      Views

      weputundefined

      well.
      i removed the M572 command and it didnt jammed.. so yeah…

      thank you dc for your formula.. I'm 100% convinced that bowden IS THE WAY TO GO.
      retraction was at 3.5mm @60mm/sec... went down to 3@40... no luck.

      i made a print with no pressure advance and it did ok (it ozzed... but ok)
      I'm testing now with 2.5mm and S0.1 to see what happens...

    • weputundefined

      Filament change macros

      Tuning and tweaking
      • • • weput
      5
      0
      Votes
      5
      Posts
      1.4k
      Views

      TYPPA Albert Einsteinundefined

      @dc42:

      If you have a PanelDue attached then you can use M300 to make it beep.

      Not have PanelDue 😞 if use Fan3?

    • weputundefined

      Pid auto tune..

      Duet Hardware and wiring
      • • • weput
      2
      0
      Votes
      2
      Posts
      717
      Views

      weputundefined

      nevermind..
      I just noticed it needs to be H1 instead of E0..

    • weputundefined

      Please help.

      General Discussion
      • • • weput
      11
      0
      Votes
      11
      Posts
      1.3k
      Views

      weputundefined

      @dc42:

      Support for other LCDs is low on the priority list because there are so many other features that users have requested - see https://www.duet3d.com/forum/thread.php?id=961. They will have to be 3.3V-compatible LCDs, not 5V ones unless you use level-shifters.

      Have you considered using your smartphone or tablet to control the Duet WiFi via the web interface, instead of an LCD?

      in fact i am… my current running setup is mks gen with octopi and i control everything remotelly... but i trend to use the kill switch of the smart controller board.