@sebkritikel
Thank you! I will try to implement your recommendations
image url)
Best posts made by SilviuZ
-
RE: Accelerometer data interpretation
Latest posts made by SilviuZ
-
RE: Toolboard 1lc v1.2 will support 2×65w heaters?
@t3p3tony thank you for your reply. I will use a mofset
-
RE: Toolboard 1lc v1.2 will support 2×65w heaters?
@pcr yes it's a option... but I was wondering about the limitations of the toolboard
-
Toolboard 1lc v1.2 will support 2×65w heaters?
Hello everyone.
I have a mosquito magnum+ and I am wondering if it is possible to change the heaters ( slice engineering 2 × 50w) with 2× 65w E3D high temperature heaters.
I know that I will be just over 5A.
There is any margin up to 5.5A?
Ps. I am running 30v -
RE: Faulty Toolboard 1LC v1.1?
@t3p3tony thank you. I bought a replacement and nothing else was damaged.
-
RE: Faulty Toolboard 1LC v1.1?
@t3p3tony ive printed a vase for 4 hours. Then i done some cleaning and weekly maintenance of the printer. I started the printer and tried to home all and the BlTouch extended the pin but no Z homing.
Flir one doesn't like close images and it's not possible to align the image correctly.
I noticed that spot on the driver and I didn't believe that could be damaged. My bad.
There is no way to save this board. Correct? -
RE: Faulty Toolboard 1LC v1.1?
@t3p3tony I've used the board for around 500 hours of printing without any hardware change. It was perfect. And the printer was going up to 450mm/s.
It didn't had any possible short 5v/30v to the ground
the printer head is not conductive and I've used the plastic washers. Something weird happened. -
RE: Faulty Toolboard 1LC v1.1?
@t3p3tony
thank you for the reply
I unplugged everything and still same problem -
Faulty Toolboard 1LC v1.1?
Re: Faulty Toolboard 1LC V1.1?
Hi.
I've updated my printer to RepRapFirmware for Duet 3 MB6HC version 3.4.0beta6
everything worked perfect up to one point when I didn't have any readings from extruder thermistor and the BlTouch didn't deploy anymore. I used my Flir camera and i noticed that there is a 100degrees Celsius hot spot on the tool board.
there is anything that I can do?image url)
11/21/2021, 5:31:36 PM M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0beta6 (2021-11-06 11:38:57) running on Duet 3 MB6HC v0.6 or 1.0 (standalone mode)
Board ID: 08DJM-956L2-G43S8-6JTD6-3SS6L-KA16H
Used output buffers: 6 of 40 (20 max)
=== RTOS ===
Static ram: 151136
Dynamic ram: 96484 of which 0 recycled
Never used RAM 103052, free system stack 202 words
Tasks: NETWORK(ready,27.3%,235) ETHERNET(notifyWait,0.1%,176) HEAT(notifyWait,0.0%,326) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.0%,903) CanSender(notifyWait,0.0%,373) CanClock(delaying,0.0%,334) TMC(notifyWait,7.3%,92) MAIN(running,65.1%,1115) IDLE(ready,0.0%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:03:53 ago, cause: power up
Last software reset at 2021-11-21 16:21, reason: User, GCodes spinning, available RAM 103264, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 128
MCU temperature: min 26.5, current 43.0, max 43.1
Supply voltage: min 29.3, current 29.3, max 29.4, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 11.9, current 12.1, max 12.7, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: pos 0, standstill, SG min 0, mspos 0, reads 65327, writes 14 timeouts 0
Driver 1: pos 0, standstill, SG min 0, mspos 0, reads 65327, writes 14 timeouts 0
Driver 2: pos 0, standstill, SG min 0, mspos 0, reads 65328, writes 14 timeouts 0
Driver 3: pos 0, standstill, SG min 0, mspos 8, reads 65331, writes 11 timeouts 0
Driver 4: pos 0, standstill, SG min 0, mspos 8, reads 65331, writes 11 timeouts 0
Driver 5: pos 0, standstill, SG min 0, mspos 8, reads 65331, writes 11 timeouts 0
Date/time: 2021-11-21 17:31:34
Slowest loop: 128.47ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.7ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 2118, received 30, lost 0, longest wait 2ms for reply type 6049, peak Tx sync delay 15213, free buffers 49 (min 48), ts 1170/10/0
Tx timeouts 0,0,1159,0,0,927 last cancelled message type 4514 dest 127
=== Network ===
Slowest loop: 6.60ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0
- Ethernet -
-
RE: InputShaping-Plugin-0.2.0-pre5 released
something that can generate multiple auto tuning algorithms similar with below to find the perfect input shaping values in type, hz and damping values
0-ei3-dba218c3 1633266073427 1000 1356 0 ei3 25 0.1 800
1-ei3-dba218c3 1633266078416 1000 1356 0 ei3 26 0.1 800
2-ei3-dba218c3 1633266083309 1000 1353 0 ei3 27 0.1 800
3-ei3-dba218c3 1633266088439 1000 1361 0 ei3 28 0.1 800
4-ei3-dba218c3 1633266093576 1000 1357 0 ei3 29 0.1 800
5-ei3-dba218c3 1633266098567 1000 1356 0 ei3 30 0.1 800
6-ei3-dba218c3 1633266103563 1000 1366 0 ei3 31 0.1 800
7-ei3-dba218c3 1633266108571 1000 1356 0 ei3 32 0.1 800
8-ei3-dba218c3 1633266113494 1000 1356 0 ei3 33 0.1 800
9-ei3-dba218c3 1633266118404 1000 1359 0 ei3 34 0.1 800
10-ei3-dba218c3 1633266123400 1000 1363 0 ei3 35 0.1 800
11-ei3-dba218c3 1633266128449 1000 1356 0 ei3 36 0.1 800
12-ei3-dba218c3 1633266133376 1000 1356 0 ei3 37 0.1 800
13-ei3-dba218c3 1633266138590 1000 1363 0 ei3 38 0.1 800
14-ei3-dba218c3 1633266143640 1000 1359 0 ei3 39 0.1 800
15-ei3-dba218c3 1633266148722 1000 1353 0 ei3 40 0.1 800 -
RE: InputShaping-Plugin-0.2.0-pre5 released
@mfs12 hi!
I've tested the plugin and its working nice.
can I suggest to have a automatic ringing test going trough the range 15-150 HZ with the option of changing in between NONE, ZVD, ZVDD EI2, EI3, minimum acceleration and the damping factor.
Thank you