Topics created by SignPostMan

@oliof OK Thanks

@jumpedwithbothfeet ```

G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"RR 650-1" ; set printer name M669 K1 ; CoreXY G21 ; Set Units to Millimeters M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet M569 P0.0 S1 ; physical drive 0.0 goes forwards M569 P0.1 S1 ; physical drive 0.1 goes forwards M569 P0.2 S1 ; physical drive 0.2 goes forwards M569 P0.3 S1 ; physical drive 0.3 goes forwards M569 P0.4 S1 ; physical drive 0.4 goes forwards M569 P0.5 S0 ; physical drive 0.5 goes forwards M569 P0.6 S0 ; physical drive 0.5 goes forwards M584 X0.5 Y0.6 Z0.0:0.1:0.2:0.3 E0.4 ; set drive mapping M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y80.00 Z800.00 E400 ; set steps per mm M906 X1600 Y1600 Z1600 E700 I30 ; set motor currents (mA) and motor idle factor in per cent -- safe for Duet 3 mini 5+ M84 S30 ; Set idle timeout M566 X600.00 Y600.00 Z8.00 E120.00 P1 ; set maximum instantaneous speed changes (mm/min) M203 X30000.00 Y30000.00 Z1600.00 E6000.00 ; set maximum speeds (mm/min) M201 X3000.00 Y3000.00 Z100.00 E3600.00 ; set accelerations (mm/s^2) M208 X0 Y0 Z0 S1 ; set axis minima M208 X650 Y650 Z480 S0 ; set axis maxima M574 X1 S1 P"io2.in" ; configure active low endstops M574 Y2 S1 P"io1.in" ; configure active high endstops ;(PanelDue is on io0) M671 X26:26:685:685 Y29:686:686:29 S5 ; position of leadscrew/bed pivot point at front left, rear left, rear right and front right M557 X30:618 Y30:650 S50 ; define 5x5 mesh grid ;PanelDue set baud rate----------------------------- M575 P1 B57600 S1 ;--------------------bed need work------------------ M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 Q11 ; create bed heater output on out5 and map it to sensor 0, lower switching frequency to 11Hz M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit ;M307 H0 A240.3 C608.7 D8.2 V24.1 B0 ; Bed Heater from other printer M140 H0 ; map heated bed to heater 0 M143 H0 S110 ; set temperature limit for heater 0 to 110C ;------------------Chamber Temp--------------------- M308 S2 P"temp1" Y"thermistor" T100000 B3950 A"Chamber"; configure sensor 2 as thermistor on pin temp2 M950 H2 C"out2" T2 ; create chamber heater output on out2 and map it to sensor 2 ;M307 H2 B0 S1.00 ; disable bang-bang mode for the chamber heater and set PWM limit M307 H2 R6 K0.17:0.11 D5.67 S1.00 ; set the process parameters for heater 1 M141 H2 ; map chamber to heater 2 M143 H2 S70 ; set temperature limit for heater 2 to 60C ;---------------------Fans------------------------- M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency M106 P0 C"Layer Fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off M950 F1 C"out3" Q500 ; create fan 1 on pin out3 and set its frequency M106 P1 C"Hotend Fan" S0 H1 T45 ; set fan 1 name and value. Thermostatic control turned on for Hotend M950 F3 C"out6" ; create fan 3 on pin out5 M106 P3 C"Chamber Filter Fan" S1 H2 T45 ; set fan 3 name and value. Thermostatic control turned on for Chamber Temp ;---------------------------------------- M563 P0 D0 H1 F0 ; define tool 1 G10 P0 X0 Y0 Z0 ; set tool 1 axis offsets G10 P0 R0 S0 ; set initial tool 1 active and standby temperatures to 0C M950 H1 C"out1" T1 ; create nozzle heater output on out2 and map it to sensor 1 M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H1 S350 ; set the maximum temperature in C for heater T0 M308 S1 P"spi.cs2" Y"rtd-max31865" ; configure sensor 1 as PT100 on pin spi.cs1 ;----Euclid Probe------------------------ M558 P8 C"io3.in" H5 F800 T10000 ; set Z probe type to unmodulated and the dive height + speeds G31 P500 X-31.5 Y0 Z3.4 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed ; Pressure Advance M572 D0 S.055 ;set tool 0 pressure advance M593 P"zvd" F41.5 ; use ZVD input shaping to cancel ringing at 40.5Hz

@Phaedrux jinx

@jay_s_uk Oh wow, I looked but did not see, thanks.

Once all the firmware was the same all works, thanks for the help!

@signpostman With the help of our internal developer, we got it work. to make it work. ON the RasPi, change file permissions on the wp_supplicant.conf file read & writeable by everyone. we then changed the "|" character to a "}". We then were able to connect.

@signpostman it literally is as simple as adding S2 to the end of your M671 line (replacing the S1 if you have it). You'll have probably put your M671 command in your config.g file, but might be in your bed.g file instead as @tecno suggests

Bltouch is the kind of thing that it pays to have a spare for. Always buy two. They work great most of the time, but the pins are fragile (I bent one just today!) and the wiring can be fragile too. Having a spare to sanity check is a big help.

@signpostman said in Mesh bed leveling Z Endstop switch:

@jay_s_uk If I want to use the CAN connection to eliminate the problem with the length of the wires, I may need the Tool Distribution Board.

Get the TDB - it makes the connection of power and CAN much easier and foolproof.

Frederick

Thanks everyone for your input!
I think I got it.
I removed the Z-Probe pin, and it now works completely.
4734c54a-89d9-47e9-8183-dace09afcd7c-image.png