@T3P3Tony Yes Phaedrux was right, that fixed it thanks
Best posts made by rister502dad
-
RE: DueX set up issues
-
RE: bed leveling
Thanks for the suggestions, I ended up getting a thicker and flatter garolite sheet. The printer can cover a bigger area but I was just using a section of it for saving time while trying to optimize
Latest posts made by rister502dad
-
RE: duex5 setup
@rister502dad ok sorry for the misunderstanding does seem to make sense to not mess with it to begin with
-
RE: duex5 setup
@Phaedrux I didn't know about this jumper until today when I was advised to remove it. Either way I still am stuck having tried both ways.
-
RE: duex5 setup
@rister502dad
Hi Phaedrux
I got this board from Filastruder on May 15th order 92688This board has actually never worked for me, the heaters work but not the steppers. I have had issues with the heaters in the past too and have wondered if there is something up with this board but then again there is a lot to understand about how the Duet works and those issues were resolved by messing around with the config file.
-
RE: duex5 setup
@dc42 Thanks for the suggestion I removed the jumper and tried again to install the firmware but it didn't work as well.
-
RE: duex5 setup
@rister502dad ```
m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.5 (2022-11-30 19:36:12) running on Duet Ethernet 1.02 or later + DueX2v0.11
Board ID: 0JD2M-9F8TA-GJ4TN-6JKDD-3SJ6S-1RU24
Used output buffers: 6 of 26 (21 max)
=== RTOS ===
Static ram: 23836
Dynamic ram: 70844 of which 40 recycled
Never used RAM 17360, free system stack 206 words
Tasks: NETWORK(ready,1511.8%,235) HEAT(notifyWait,7.2%,344) Move(notifyWait,1.1%,363) DUEX(notifyWait,0.0%,24) MAIN(running,8228.0%,464) IDLE(ready,0.0%,30), total 9748.0%
Owned mutexes:
=== Platform ===
Last reset 11:34:53 ago, cause: power up
Last software reset at 2023-05-31 18:37, reason: User, GCodes spinning, available RAM 17360, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 20.2, current 22.2, max 24.0
Supply voltage: min 0.5, current 0.6, max 0.6, under voltage events: 0, over voltage events: 0, power good: no
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: ok, SG min n/a
Driver 1: ok, SG min n/a
Driver 2: ok, SG min n/a
Driver 3: ok, SG min n/a
Driver 4: ok, SG min n/a
Driver 5: ok, SG min n/a
Driver 6: ok, SG min n/a
Driver 7:
Driver 8:
Driver 9:
Driver 10:
Driver 11:
Date/time: 2023-06-01 17:24:02
Cache data hit count 4294967295
Slowest loop: 4.65ms; fastest: 0.14ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== DueX ===
Read count 0, 0.00 reads/min
=== Network ===
Slowest loop: 6.22ms; fastest: 0.05ms
Responder states: HTTP(0) HTTP(2) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
Interface state active, link 100Mbps full duplex -
RE: duex5 setup
Here the firmware says its for a duex2 after updating using the DWC firmware upload tool
-
duex5 setup
Hello,
I have a Duet2-Ethernet and a Duex5 expansion board, I can't figure out how to install the firmware correctly using the Reprap configuration tool, I select the DueX5 expansion board but the firmware that I end up downloading still puts DueX2 firmware on my board. Does anyone know what I am missing? thanks
-
RE: bed leveling
Thanks for the suggestions, I ended up getting a thicker and flatter garolite sheet. The printer can cover a bigger area but I was just using a section of it for saving time while trying to optimize