Hi, any idea where to order keenovo pads in the UK /eu please? Looking for 500x500 approx
Posts made by FuseDeep
-
RE: Keenovo 240v bed/ssr/fusing /examples?
-
Keenovo 240v bed/ssr/fusing /examples?
Re: Adding mains 6amp 240v heated bed to Duet2 wifi
Hi all,
Does anyone have suggestions on which ssr to use with a duet2 and a suitable fuse system for a keenovo bed at 6A iirc.
Decided to add heated bed to
Regards Rich
-
Tony at Oxford/ heating issue/240v bed control .
Hi,
My very useful printer
Is generally running fab, however it has an intermittent issue. I bumped into Tony at smrrf/Oxford and we briefly discussed it. Cheers Tony. Was a great show!
When heating from cold it will quite often bork out and the warning says;
Hot end heating too slow at 1. 2 degrees /second etc
This trips a fault and stops heating.
A pain. Need to widen the heating safety variable. There is no fault with the heater.
Also, can I run a 240v heated bed via my duet2 wifi?
Will look at my post on this when I work out how to search my own posts!
Regards Rich
-
RE: MakerGear M2 z issue/board Z drive?
I canged the z/E1 output MA from 800 to 1600 and it is much happier (0nly cost me 100gbp to not fix this!).
Seems it needed more current. will relube and see how she runs!
-
RE: MakerGear M2 z issue/board Z drive?
Hmmm
Have saved and checked the new config file and still have a weak as a kitten Z axis.
Please note, the set up worked perfectly for many months then suddenly became weak.
I replaced the entire Z stepper direct from makergear (the old z steppers were known to fail after a decade) and have checked continuity on all 4 stepper cables, all good.
This is now a new z stepper and re assigned as above, but with exact same weakness issue!!!!!!
What is the max current I can set for the duet wifi board for a stepper drive channel, maybe the z set up is stiffer and needs more power (only thing that makes sense)?
Cheers Richard
-
RE: MakerGear M2 z issue/board Z drive?
@jay_s_uk yes, no problem opening it. but when wanting to save as a congig.g file I can't see the G extension option in the save as....can't remeber what I did last time?
-
RE: MakerGear M2 z issue/board Z drive?
@jay_s_uk Thanks, I have notepad but can't find the G option in the drop down, is there a nack to it?
-
RE: MakerGear M2 z issue/board Z drive?
@jay_s_uk Please remind me how to save a config. g file, I had a specific piece of software but can't find it now!
And yes, I was awoken 0400 this morning by the wind and rain...
-
RE: MakerGear M2 z issue/board Z drive?
M569 P2 S0 ; physical drive 2 goes forwards
replace w
M569 P4 S0 ; physical drive 2 goes forwards
-
RE: MakerGear M2 z issue/board Z drive?
To change Z axis drive to E1/4 is this the correct change (it has been some months since I touched any of this stuff); Do i need to do anything else, other than move stepper plug to correct output on board?
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Wed Apr 20 2022 11:07:59 GMT+0100 (British Summer Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"DUET 0.6mm HB / Son.im" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z4 E3 ; set drive mapping (changed Z from 2 to drive motor 4 (E01)
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X88.89 Y88.89 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X200 Y250 Z185 S0 ; set axis maxima; Endstops
M574 X1 S1 P"!xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 P"!zstop" ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin zstop; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:200 Y15:195 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.227 K0.317:0.000 D10.46 E1.35 S1.00 B0
; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H0 T40 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
M552 S2 -
RE: MakerGear M2 z issue/board Z drive?
This is my current config file;
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Wed Apr 20 2022 11:07:59 GMT+0100 (British Summer Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"DUET 0.6mm HB / Son.im" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X88.89 Y88.89 Z400.00 E420.00 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X200 Y250 Z185 S0 ; set axis maxima; Endstops
M574 X1 S1 P"!xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"!ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 P"!zstop" ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin zstop; Z-Probe
M558 P0 H5 F120 T6000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:200 Y15:195 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 R0.227 K0.317:0.000 D10.46 E1.35 S1.00 B0
; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H0 T40 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H-1 ; set fan 1 value. Thermostatic control is turned off; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C; Custom settings are not defined
M552 S2 -
RE: MakerGear M2 z issue/board Z drive?
@jay_s_uk thanks. Am running an extruder and 3 axis currently.
That would be great if there are 2 extruder outputs. Will have a look.
-
MakerGear M2 z issue/board Z drive?
Hi,
After a decade my M2 showed the known fault, a weak z drive stepper (direct threaded).
I checked a few connections, all seemed fine, and ordered the MakerGear z stepper w in built screw thread from USA.
Swapped out the Z stepper... And exactly the same problem so can't print.
I need to double check the wiring proper, but if not that, then how do I check my duet board for drive failure, or, can I assign the Z to the Z/ B driver (or another axis drive) ?
Any suggestions appreciated.
Thanks Rich
-
RE: HELP! Can't log in to both machinesWIFI passwords!?
PS.
In modern windows you have to enable view file extension in folder settings too!
In the old days you could simply edit, but they are trying to tidy up, apparently...
Really, that’s it. Microsoft may think it makes for less confusion, but the reverse is true.
//
It’s pretty clear by now that Microsoft is unlikely to see the light and display file extensions by default in any version of Windows. That doesn’t matter because you can take charge of the situation yourself and turn extension display on:
Open any folder window.
Press Alt+T+O (that’s the letter O, not a zero) to open the Folder Options dialog box.
Click the View tab.
Remove the tick (checkmark) beside ‘Hide extensions for known file types’ and click OK.//
-
RE: HELP! Can't log in to both machinesWIFI passwords!?
Yes, exactly as Ian said.
Thank you so much everyone above for your constructive suggestions and comments.
I have now stopped sobbing into my keyboard!
And written the password clearly on each machine.
-
RE: HELP! Can't log in to both machinesWIFI passwords!?
M552 S0 ; sets WiFi to idle
G4 S5 ; wait 5 seconds for WiFi to turn off
M589 S"DuetSSID" P"Point6" I192.168.0.1
G4 S5 ; wait again
M552 S2 ; enable access pointI dropped this into macros folder as a g file extension
It does not work.
-
RE: HELP! Can't log in to both machinesWIFI passwords!?
I have added;
M589 S"DuetSSID" P"password" I192.168.0.1
To my point 6 (with my password) and it won't accept the password.
Nor will my phone.
Or my other laptop.
They keep asking for NETWORK SECURITY KEYS, I don't think this is anything to do with gcode passwords and a fundamental password deep in duet that is either borked or I forgot.
It's a real problem people.
I was nervous about going wifi, and this is exactly why...