Thanks again, updating from duet board worked. Digitizer doesn't work though but that's a separate issue
Best posts made by cdoe
-
RE: Issues flashing firmware to PanelDue 7i over USB
Latest posts made by cdoe
-
RE: Issues flashing firmware to PanelDue 7i over USB
Thanks again, updating from duet board worked. Digitizer doesn't work though but that's a separate issue
-
RE: Issues flashing firmware to PanelDue 7i over USB
Thanks I'll try that. Didn't realise it can be done while paneldue has no firmware at all...
-
RE: Issues flashing firmware to PanelDue 7i over USB
I've been able to flash 3.4.1 with bossac. GUI version is windows/macos version only which i don't have, so it seems that my paneldue is now just a bunch of useless hardware
-
RE: Issues flashing firmware to PanelDue 7i over USB
bossac says “flash command failed”
-
Issues flashing firmware to PanelDue 7i over USB
Hi,
I've tried re-flashing 3.5.0 rc 8 firmware over usb and followed process described in documentation.
PanelDue had 3.4.1 firmware previously. However, it was in storage and was stuck in calibration prompt - i.e. a dot on top of the screen was visible and there was a prompt to touch it, but that was not progressing as if touch was not detected.
Here are some outputs from bossac:$ ./bossac --port=/dev/ttyACM0 -i Atmel SMART device 0x289b09e0 found Device : ATSAM4S4 Chip ID : 289b09e0 Version : v1.13 RC2 Feb 20 2013 13:25:17 Address : 4194304 Pages : 512 Page Size : 512 bytes Total Size : 256KB Planes : 1 Lock Regions : 16 Locked : none Security : false Boot Flash : false
output when flashing with 3.5.0:
./bossac --port=/dev/ttyACM0 -e -w -v -b ~/Downloads/PanelDueFirmware-3.5.0-rc8-7.0i.bin Atmel SMART device 0x289b09e0 found Erase flash done in 0.001 seconds Write 176720 bytes to flash (346 pages) [ ] 0% (0/346 pages) Flash command failed
Similar output when trying with version 3.4.1:
./bossac --port=/dev/ttyACM0 -e -w -v -b ~/Downloads/PanelDueFirmware-3.4.1/PanelDueFirmware-3.4.1-7.0i.bin Atmel SMART device 0x289b09e0 found Erase flash done in 0.001 seconds Write 170916 bytes to flash (334 pages) [ ] 0% (0/334 pages) Flash command failed
Are there any troubleshooting steps I could try to figure out why flashing no longer works and if hardware is in working condition?
There are no torn wires or connector strips on visual inspection -
RE: Smart Effector replacement LEDs
Only got my hands to it now. Sadly 140R resistor burned out so badly that there are no traces left to put replacement component. LEDs are fine though. Has anyone tried using silver tracing pen to re-draw traces? Will it work properly with moving part like effector?
-
Smart Effector replacement LEDs
Is there something similar to replacement parts for duet3d but for smart effector?
I'll need to replace LEDs (D1, D9 and D7) as I was switching from 24v to 12v and then back and forgot to remove 12v jumper for LEDs so they were working w/o extra resistor for some time. -
RE: 12V Fan connections from 24V PSU
When +12V is connected to centre pin of V_FAN voltage selection block - does it bypass mosfets? Also do I need to connect negative from buck converter to negative of duet wifi? Looks like negative from buck converter output is common on both sides so it's common with negative on PSU as well.