Posts made by 3dpnut

@Phaedrux Sorry, its a setting in YAT. It is connected now, fingers crossed it stays that way!

@Phaedrux I don't know what they are. I changed my terminal type from binary to text, and it's connected now. Previously I had to change it the other way for it to work...not sure what the correct setting is for that.

Sends back:

6Dh 35h 38h 37h

I turned the machine on today, and it seems like I turned back the clock 2 weeks. The same thing is happening, not connecting to Wifi. I've run through the same cycles which fixed it last time, no luck. I ran M997 S1, and it re-installed the firmware fine. Then ran M552 S0, OK. Then M552 S1, OK. Then M587 S"xx" P"xx", and it says OK, then times out and says wifi module is idle. My computer is connected to the same network and is connected no problem. I double-checked the password and it's correct.

What am I doing wrong?

Thanks all!! Everything is now working with the exception of a Z homing issue, which I think I can (hopefully :)) figure out. Have a great weekend!

@dc42 I'll try again:

This is what I get after successfully running M997 S1:

95% complete
Upload successful
ok
M552 s1
ok
WiFi module started
WiFi reported error: no known networks found
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle
M552 s0
ok
WiFi reported error: no known networks found
WiFi module is idle
M552 S1
ok
WiFi reported error: no known networks found
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle
WiFi reported error: no known networks found
WiFi module is idle

@dc42 I'm trying to load the results of M997 S1 and the subsequent M552's, but it blocking me as spam by Askimet.com

@dc42 Thank you! I made the change and now it's speaking to the Paneldue. Still no luck with the wifi tho

@Phaedrux This is what I'm getting:

M552
WiFi module is being started
ok
M552 s1
Turn off the current WiFi mode before selecting a new one
ok
M552 S0
ok
M552 S1
Turn off the current WiFi mode before selecting a new one
ok
M552 S0
ok
M552
WiFi module is being started
ok
M552 S1
Turn off the current WiFi mode before selecting a new one
ok

The MCU temp should read close to room temp, which is 69 deg F, any ideas why this reading? Also, I'm feeding in 24v (which I've checked and is correct), so no idea why it's reading 16v.

I put the M552 S"Network" P"Password" in, and it says "ok", but doesn't give me the IP address...

@Phaedrux thanks for the reply.
M115: FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 3.1.1 ELECTRONICS: Duet WiFi 1.02 or later FIRMWARE_DATE: 2020-05-19b2
ok
M122:
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6B2-NJ4S4-6J9F6-3SD6J-1U1GL
Used output buffers: 1 of 24 (2 max)
=== RTOS ===
Static ram: 27980
Dynamic ram: 93916 of which 44 recycled
Exception stack ram used: 308
Never used ram: 8824
Tasks: NETWORK(ready,1892) HEAT(blocked,1224) MAIN(running,1824) IDLE(ready,80)
Owned mutexes:
=== Platform ===
Last reset 00:01:24 ago, cause: power up
Last software reset details not available
Error status: 0
MCU temperature: min -72.1, current -67.6, max -65.6
Supply voltage: min 16.3, current 16.3, max 16.7, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 1970-01-01 00:00:00
Cache data hit count 140654521
Slowest loop: 5.06ms; fastest: 0.13ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 3.1ms, write time 0.0ms, max retries 0
=== Move ===
Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
Bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== AuxDDARing ===
Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is ready with "m122" in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 0.25ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 0 of 8

• WiFi -
  Network state is starting2
  WiFi module is disabled
  Failed messages: pending 0, notready 0, noresp 0
  Socket states: 0 0 0 0 0 0 0 0
  ok

A screw fell onto the motherboard and blew the fuses. I purchased a replacement board and Paneldue from CapstoneCADEM. After installing both boards the paneldue says "connecting" and doesn't control anything. It also will not connect to wifi. I tried everything I could find on the forum, M552 S1 finds the network, then says " no known networks found", then continues in the same order to loop. I've reflashed the firmware, replaced the cable, no luck. The bad part is I have work mounding up - please somebody help!!

Re: Got my paneldue... It says "connecting" and controls nothing...

@Steve-Lynch did you ever figure out what was going wrong? I have exactly the same issue...

Thanks very much for the quick response! I'm struggling with the mapping, I'm getting a whole string of errors relating to a "non-existent tool". Also, Drive 3 (the bad one) still gets hot. The board has several spare drives because I'm using the breakout extender board. I only have one extruder, which is plugged into Heater 0, Drive 4. Here is what I have:

M569 P0 R-1 ; Drive 0 disabled
M569 P1 R-1 ; Drive 1 disabled
M569 P2 R-1 ; Drive 2 disabled
M569 P3 R-1 ; Drive 3 disabled
M569 P4 S1 ; Extruder goes forwards
M569 P5 T2 ; 2 microsecond minimum step pulse width for x-axis
M569 P6 T2 ; 2 microsecond minimum step pulse width for y-axis
M569 P7 T2 ; 2 microsecond minimum step pulse width for z-axis
M584 X5 Y6 Z7 E4 ; Apply custom drive mapping (X=Drive5, Y=Drive6, Z=Drive7, E4-Extruder1)

What am I doing wrong?

I have Duet2 Wifi, and accidently disconnected an extruder motor while the control box was on. I plugged it back in, and now it gives an error message that driver 3 detected a temperature overload, and the driver chip next to the extruder motor plug instantly gets incredibly hot, and has what looks like melted spots. I unplugged the motor, and one by one the heater, fan, thermistor, but it still does the same thing, and will not turn. I tried plugging in other motors, and the result is the same. I checked the wiring, it all looks OK. Any help would be appreciated!!

Hello All,

I'm a newbie, technical background, but new to electronics and code. I am struggling to set up a high-output extruder which has 1 stepper drive and 3 heaters along the length of the nozzle. The Duet2 has a breakout board which drives X, Y, and Z. I plugged 2 of the heaters into E0 and E1 heater terminal blocks and 2 Dyze high-temp sensors into E0 and E1 VSSA thermistors. I have attempted to add an adafruit max31865 to the board temp daughterboard to run the 3rd sensor. I'm not quite sure where to plug the 3rd heater into. I have plugged an external stepper driver (Rtelligent R60) into Drive 4, and the extruder stepper motor into it. On the 2 heaters plugged in I'm getting very low readings, jumping from 2 degrees to 13.8 degrees. The heaters to not follow heat commands from the controller, and the extruder stepper doesn't either. Follows is my config.g, any help/suggestions/criticism would be much appreciated

; Configuration file for Duet WiFi (firmware version 1.19.2)
; executed by the firmware on start-up
;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; DRIVES ;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S1 ; left extruder goes forwards
M569 P4 S1 ; right extruder goes forwards
M569 P5 T2 ; 2 microsecond minimum step pulse width for x-axis
M569 P6 T2 ; 2 microsecond minimum step pulse width for y-axis
M569 P7 T2 ; 2 microsecond minimum step pulse width for z-axis
M569 P8 S1 R0 ; Drive 8 goes forwards
M584 X5 Y6 Z7 E4 ; Apply custom drive mapping (X=Drive5, Y=Drive6, Z=Drive7, E3=Extruder0, E4-Extruder1 )
M350 X16 Y16 Z16 E16:16:16 I1 ; Configure microstepping with interpolation
;M92 X120 Y120 Z2000 E478:463 ; Set steps per mm
M92 X120 Y120 Z2000 E379224.6 ; Set steps per mm
M566 X225 Y225 Z12 E120:120:120 ; Set maximum instantaneous speed changes (mm/min)
M203 X12000 Y12000 Z180 E6000:6000:6000 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z250 E250:250:250 ; Set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1680:1680:1680 I30 ; Set motor currents (mA) and motor idle factor in percent
M84 S30 ; Set idle timeout

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; HEATERS ;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

;M143 S300 ; Set maximum heater temperature to 300C
M143 S500 ; Set maximum heater temperature to 450C
M143 H0 S150 ; set max bed temp to 150C
M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater(may require further tuning)
;M301 H1 S1.0 P7 I0.25 D34.5 T0.4 W180 B30 ; Use PID on extruder1 (may require further tuning)
;M301 H2 S1.0 P7 I0.25 D34.5 T0.4 W180 B30 ; Use PID on extruder2 (may require further tuning)
M305 P0 T47500 B4050 C0 R4700 ; Set thermistor + ADC parameters for heater 0
;M305 P1 T100000 B4210 C0 R4700 ; Set thermistor + ADC parameters for heater 1
;M305 P2 T100000 B4100 C0 R4700 ; Set thermistor + ADC parameters for heater 2
M305 P1 T4606017 B5848 C5.548428e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M305 P2 T4606017 B5848 C5.548428e-8 R4700 ; Set thermistor + ADC parameters for heater 1
M305 P6 T4606017 B5848 C5.548428e-8 R5100 ; Set thermistor + ADC parameters for heater 6
M307 H1 A655 C573.6 D11.8 S1.0 B0
M307 H2 A655 C573.6 D11.8 S1.0 B0
M307 H6 A409.7 C570.6 D28.6 S1.0 B0
M570 H1 T25 ; Allow temperature excursion
M570 H2 T25
M570 H6 T25
M302 P1
M305 P6 X203

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; TOOLS ;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

M563 P0 D4 H1:2:6 ; Define tool 0
G10 P0 X0 Y0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C
;M563 P1 D0 H2 ; Define tool 1
;G10 P1 X99.21 Y-1.18 ; Set tool 1 axis offsets
;G10 P1 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C
;M563 P2 D0 H6 ; Define tool 2
;G10 P2 X99.21 Y-1.18 ; Set tool 2 axis offsets
;G10 P2 R0 S0 ; Set initial tool 1 active and standby temperatures to 0C

;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;; CUSTOM SETTINGS ;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;

T0 ; Select tool to activate heater