duet 2 wifi ona ctc dual help plz
-
when i try to home any of the axis it give me error g28 x g28 y and g28 z here are the files also. the printer will not do anything but move the extruter stepper it will not even heat the bed or the extruters. i am new to all this i dont know much about gcode at all. if you need any other files let me know thank you again for the help.
3_1552925130018_homez.g 2_1552925130018_homey.g 1_1552925130018_homex.g 0_1552925130018_config.g
-
@twistedechos said in duet 2 wifi ona ctc dual help plz:
when i try to home any of the axis it give me error
What is the error?
-
it is g28
-
but what does the error message say?
-
sorry it says g28 homing failed
-
i should specify that it is under the duettest interface idk where else to look for the erorrs
-
@twistedechos said in duet 2 wifi ona ctc dual help plz:
sorry it says g28 homing failed
Is that the only error message? If so, that indicates that you sent a G28 command to home the printer, but the commands in your homing file didn't cause the motor to move so as to trigger your homing switch.
Have you tested the motors individually? To do that, first send command G91 to select relative coordinates. Then send G1 s2 commands to command the motors. For example, G1 S2 X50 commands the X motor to move 50mm in the +X direction. Command G1 S2 X-50 commands it to move 50mm in the -X direction.
-
I think you may benefit from this guide: https://duet3d.dozuki.com/Wiki/ConfiguringRepRapFirmwareCartesianPrinter
-
i get m120
g91
g1 x-100 f6000
m121
error g0/g1 insufficient axes homed
the only thing it will let me do is click the retract and extrude extruder 1
if i can up load a video i can show you everything i think i might need to redo the reprap config or something but i dont know my min and max axis settings -
Can you post your homeall as well?
error g0/g1 insufficient axes homed
This happens when trying to move an axis before it is homed. Usually this is when the Z axis is lifted a bit to give clearance for homing X and Y.
From the FAQ: https://duet3d.dozuki.com/Wiki/FAQ
I get this error message: "Error: G0/G1: insufficient axes homed"
Recent firmware versions do not allow axes to be moved before they have been homed. The only movements allows are homing moves (G1 moves with S1 or H1 parameter) and individual motor moves (G1 moves with S2 or H2 parameter). So any Z movements that your homing files make before Z is homed should use the S2 parameter. Alternatively, add M564 H0 to config.g to allow axis movement before homing. -
This post is deleted! -
it wont let me upload the vid
-
Might need to use Dropbox or YouTube
-
https://youtu.be/ZGwYuOgqCJM here it is if you need any other info from me let me know in the mean time im going to read up on the links you sent me
-
i wonder if anyone has the original gcode files for the ctc my old board fried if i could get those i should just be able to upload them to the board right?
-
https://3dprinting.com/pricewatch/3d-printer/ctc-bizer/?fbclid=IwAR1yXJLIZn4f_zbPCmQrPTTxfIqpmlKQ0ub-9Qjie7nvzTodRKtTxSwOO3I if this helps at all this is the printer i have
-
also i went thought the stuff you sent and it didnt do anything i think i need to reuplaod the files on it but i dont think i did the maserments right on the reprap config i think that might be the problem how do i find them all i can find on google is the bed size
-
i feel so dumb i think i found the problem i did not put the files under sys it is under another folder ill let you know what i find out
-
ok that fixed it oi lol but now the problem is i dont think i have the right measurements or the home set properly i went thought the reprap config again and i dont know the specs for the printer nor understand what to do with them
-
found another problem haha sorry to be spamming but i had it as a corexy (what i thought it was) its a cartesian
