Issues with motors..... Don't move

[peirof]

For tests i have do....

All, minus motors, works....

[peirof]

If i conect a multimeter, to axis sockect, PIN X and Y (i dont know what pins)...... and command a move order to printer, that involves that axis, i have to see Voltage in multimeter? What range?1.0 A, aprox?

[dc42]

You can connect a multimeter set to a voltage range to pairs of stepper driver output pins, but be very careful not to short them together!

When you command a motor to move for the first time after powering up the Duet, does the axis become stiff and harder to turn by hand?

Please try commanding some motors to move, then send M122 once and post the report here.

[peirof]

@dc42

i send by console G91 and after G1 S2 X10.... and axis stiff, the same with Y and Z

after send a M122, the results

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.02(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-956GU-DJMSN-6J1DJ-3S86S-K9RBH
Used output buffers: 1 of 20 (15 max)
=== RTOS ===
Static ram: 25524
Dynamic ram: 98632 of which 0 recycled
Exception stack ram used: 328
Never used ram: 6588
Tasks: NETWORK(ready,680) HEAT(blocked,1232) MAIN(running,3860) IDLE(ready,200)
Owned mutexes:
=== Platform ===
Last reset 00:07:29 ago, cause: power up
Last software reset at 2019-01-06 18:27, reason: User, spinning module GCodes, available RAM 6452 bytes (slot 2)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 36.4, current 38.5, max 38.8
Supply voltage: min 24.5, current 24.7, max 24.9, under voltage events: 0, over voltage events: 0, power good: yes
Driver 0: ok, SG min/max not available
Driver 1: ok, SG min/max not available
Driver 2: ok, SG min/max not available
Driver 3: ok, SG min/max not available
Driver 4: ok, SG min/max not available
Date/time: 2019-01-07 16:26:37
Cache data hit count 1683481520
Slowest loop: 2.26ms; fastest: 0.08ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 239, MaxWait: 297717ms, Underruns: 0, 0
Scheduled moves: 3, completed moves: 3
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 2 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 168.39ms; fastest: 0.08ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8

• WiFi -
  Network state is running
  WiFi module is connected to access point
  Failed messages: pending 0, notready 0, noresp 0
  WiFi firmware version 1.21
  WiFi MAC address 5c:cf:7f:76:73:23
  WiFi Vcc 3.29, reset reason Turned on by main processor
  WiFi flash size 4194304, free heap 15528
  WiFi IP address 192.168.1.200
  WiFi signal strength -44dBm, reconnections 0, sleep mode modem
  Socket states: 0 0 0 0 0 0 0 0

[peirof]

What can i do?

[dc42]

Please post your config.g file.

[sigxcpu]

@peirof M119 ?

[peirof]

Hi,

Config.g

; Configuration file for Duet WiFi (firmware version 1.17)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool on Fri Aug 04 2017 00:02:04 GMT-0400 (Eastern Daylight Time)

; General preferences
M111 S0 ; Debugging off
G21 ; Work in millimetres
G90 ; Send absolute coordinates...
M83 ; ...but relative extruder moves
M555 P1 ; Set firmware compatibility to look like RepRapFirmare
M665 R157 L397.1073 B175 H500.3 ; Set delta radius, diagonal rod length, printable radius and homed height
M666 X0 Y0 Z0 ; Put your endstop adjustments here, or let auto calibration find them
M208 Z0 S1 ; Set minimum Z

; Endstops & Monitoring aa
M574 X2 Y2 Z2 S1 ; Define active high microswitches
M557 R110 S25 ; Define mesh grid
M911 S12.0:19.5:22.0 ; Auto-pause at 19.5V, then either stop at 12V or auto-resume at 22V

;DESACTIVAR EL PIN DEL HEATER7, EN EL SOCKET DE EXPANSION

;Zprobe Precision Piezo

; M558 P0
M558 P8 I1 R0.4 F500 X0 Y0 Z0; M558 P8 I1 R1 F300 X0 Y0 Z0 H2 / M558 P5 I1 R0.4 F300 H5 X0 Y0 Z0 T2400
G31 X0 Y0 Z-0.1 P400 ;(X, Y, Z offsets, debounce interval)

; Drives
M569 P0 S1 ; Drive 0 goes forwards
M569 P1 S1 ; Drive 1 goes forwards
M569 P2 S1 ; Drive 2 goes forwards
M569 P3 S0 ; Drive 3 goes reverse
M350 E16 I1 ; Configure microstepping with interpolation
M350 X32 Y32 Z32 I1 ; Configure microstepping with interpolation
M92 X160 Y160 Z160 E415 ; Set steps per mm
M566 X1200 Y1200 Z1200 E1200 ; Jerk Set maximum instantaneous speed changes (mm/min)
M203 X18000 Y18000 Z1800 E1200 ; Set maximum speeds (mm/min)
M201 X1000 Y1000 Z1000 E1000 ; Set accelerations (mm/s^2)
M906 X1200 Y1200 Z1200 E800 I40 ; Set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Pressure in advance

M572 D0 S0.08 ; Setup for pressure in advance

; Heaters
M143 S285 ; Set maximum heater temperature to 285C
M301 H0 S1.00 P10 I0.1 D200 T0.4 W180 B30 ; Use PID on bed heater (may require further tuning

M305 P0 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 0
M305 P1 T100000 B4138 C0 R4700 ; Set thermistor + ADC parameters for heater 1

; Tools
M563 P0 S"Prometheus" D0 H1 F1 ;M563 P0 D0 H1 ; tool(P)0 Nombre(S) Motor de extrusion(D)0 Calentador(H)1 y Ventilador(F)1
G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets
G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C

; Network
M550 PTLM Duet 2 ; Set machine name
M587 S"TERRAZAExtender2.4GHz" P"a1b2c3d4" I192.168.1.200
M552 S1 ; Enable network
M586 P0 S1 ; Enable HTTP
M586 P1 S0 ; Disable FTP
M586 P2 S0 ; Disable Telnet

; Fans
M106 P0 H-1 ; GCODE FAN
M106 P1 H-1 ; GCODE FAN
M106 P2 S1 I0 F500 H1 T205 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on a 70C

; Custom settings are not configured

; Miscellaneous
M501 ; Load saved parameters from non-volatile memory

M119

Endstops - X: not stopped, Y: not stopped, Z: not stopped, Z probe: not stopped

[peirof]

Hi,

An idea it's make a Soft reset... How would the procedure?

[dc42]

@peirof said in Issues with motors..... Don't move:

Hi,

An idea it's make a Soft reset... How would the procedure?

Sending M999 causes a software reset.

[peirof]

@dc42 Ok... Later try... Exist, in Duet, a Hard reset?

[Dougal1957]

@peirof said in Issues with motors..... Don't move:

M558 P8 I1 R0.4 F500 X0 Y0 Z0; M558 P8 I1 R1 F300 X0 Y0 Z0 H2 / M558 P5 I1 R0.4 F300 H5 X0 Y0 Z0 T2400

I could be way of the mark here but in this line
M558 P8 I1 R0.4 F500 X0 Y0 Z0; M558 P8 I1 R1 F300 X0 Y0 Z0 H2 / M558 P5 I1 R0.4 F300 H5 X0 Y0 Z0 T2400

is the semicolon directly after the Z0 ok or does it need a space in there?

Doug

[peirof]

@dougal1957

i am not sure, but think this is not the problem, the printer has been working with these config.g, months....

[peirof]

Well....eeee, not, bad.

I have do the test i have comented, soft reset and with a new MicroSD, reinstall printer.... and the same.

ALL WORKS (HEATERS, TERMISTORS, ENDSTOPS, ZPROBE,....) MINUS STEPPERS MOTORS

Only rest, think, is test of drivers of Duet, think TMC2660, are working ok...

How can test this point?
Its strange that all drivers goes off at the same time. Why?
Something more to test?

These look bad....

Now i have no ideas.....

@dc42, please HELP!!!!!!!!!!!!!!

[dc42]

Please verify the following:

1. When you power up the Duet, initially it is possible to move the carriages of your printer by hand (slowly!), because the motors are not energised.

2. If you send the following commands:

G91
G1 S2 X-10

then the X motor does not move.

3. After sending those commands, the X carriage is difficult to move (because there is current in the X motor). But the Y and Z carriages are still easy to move.

4. Sending this;

G91
G1 S2 Y-10

doesn't make the Y motor move, but does lock the Y motor.

5. Sending this;

G91
G1 S2 Z-10

doesn't make the Z motor move, but does lock the Z motor.

6. After sending these commands, there are no error messages reported in the GCode console.

Is all of that correct?

[peirof]

@dc42

No, it is not correct.

The motors ever, after send the gcode (G1 S2 X-10 or G1 S2 Y-10 or G1 S2 Z-10), are smooth to move, are not energiced....

[dc42]

@peirof said in Issues with motors..... Don't move:

The motors ever, after send the gcode (G1 S2 X-10 or G1 S2 Y-10 or G1 S2 Z-10), are smooth to move, are not energiced....

In that case, I think there may be a problem with the ENN signal that goes from the processor to all the drivers. This signal is also present on the expansion connector (see the label underneath for which pin it is). You could measure the voltage between it and ground (which you can connect to on any endstop connector) using a multimeter. With USB power only applied, it should be at +3.3V. When VIN power is applied, it should drop to 0V, which enables the drivers.

[peirof]

Hi,

If I did not understand wrong, the procedure would be:

1- Disconnect, Duet3d Board, from power.
2- Connect Duet3d, with the USB cable to a PC.
3- I check the voltage, in the expansion module, between the pins, pin 28 (ENN) and pin 2 (GND).
4- With Duet3d Board, WITHOUT ELECTRIC CURRENT but with the USB connected, the reading on the voltage meter would have to be 3.3V.
5- I turn on the PSU, as soon as I turn it on, the voltage should drop to 0.0V.

Okay?

[peirof]

Hi,

tests do its.... i send images.

ONLY WITH USB TO LAPTOP

WITH TLM PSU ON

Something its wrong. No?. But what.... and.... WHY?

[peirof]

Some tips for I can do?