Can't upload G-code
-
I've just updated an old AnyCubic delta machine with a spare Duet board, and all was going fine for a few days, but this afternoon I can't upload any new files.
Initially everything looks fine ...
But then it comes up with an error.
And the file is not uploaded. I've tried two different computers, with Firefox and Chrome. Same error every time. I've also tried different files. There was at 10MiB file on there I removed to check the card had space, but it didn't make any difference.
Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 2.01(RTOS) (2018-07-26b2)
WiFi Server Version: 1.21
Web Interface Version: 1.22.3
Web Interface by Christian Hammacher
Licensed under the terms of the GPL v3Thank you for any help.
-
Can you copy and paste the results of an M122 diagnostics report?
-
That indicates either an SD card write error, or that the size of the file size written wasn't correct.
Perhaps you should try a different SD card?
-
M122 output
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 2.01(RTOS) running on Duet WiFi 1.02 or later
Board ID: 08DGM-9568A-F23SD-6J1F2-3SD6R-KVNMD
Used output buffers: 3 of 20 (11 max)
=== RTOS ===
Static ram: 28476
Dynamic ram: 96312 of which 16 recycled
Exception stack ram used: 320
Never used ram: 5948
Tasks: NETWORK(ready,400) HEAT(blocked,1248) MAIN(running,3540)
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:15:43 ago, cause: power up
Last software reset at 2018-09-10 16:36, reason: User, spinning module GCodes, available RAM 5948 bytes (slot 1)
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 0.0ms, max retries 0
MCU temperature: min 22.1, current 33.5, max 34.3
Supply voltage: min 12.2, current 12.3, max 12.5, under voltage events: 0, over voltage events: 0
Driver 0: standstill, SG min/max not available
Driver 1: standstill, SG min/max not available
Driver 2: standstill, SG min/max not available
Driver 3: standstill, SG min/max not available
Driver 4: standstill, SG min/max not available
Date/time: 2018-09-11 09:42:02
Slowest loop: 8.32ms; fastest: 0.07ms
=== Move ===
Hiccups: 0, StepErrors: 0, LaErrors: 0, FreeDm: 240, MinFreeDm: 240, MaxWait: 0ms, Underruns: 0, 0
Scheduled moves: 0, completed moves: 0
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Stack records: 1 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
=== Network ===
Slowest loop: 37.13ms; fastest: 0.01ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
HTTP sessions: 1 of 8- WiFi -
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.21
WiFi MAC address 2c:3a:e8:0b:27:ec
WiFi Vcc 3.47, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 14304
WiFi IP address 172.16.28.198
WiFi signal strength -73dBm, reconnections 0, sleep mode modem
Socket states: 0 0 0 0 0 0 0 0
=== Expansion ===
I'll try another card too
- WiFi -
