New firmware 1.21RC1 available
-
Thanks for you report.
Regarding the printer becoming very slow, I have one other report of this, also on a Duet Ethernet. Next time it happens, please use M111 to enable GCodes, Move and DDA debugging. Then send a movement command. It will echo the gcode, then the move details, then do the move. What I am interested in is where the delay occurs.
My machine just finished a print and since I was sitting by it, I immediately commanded it to turn on relay output after it finished the end.g script. It responded quickly. However a short while after that, I attempted to home the machine and it was slow to respond.
-
Any idea about the move on resume? Bug or bad script?
-
@nyt:
Any idea about the move on resume? Bug or bad script?
Are you sure that isn't a normal printing move? It looks to me that it is printing one full line of the inner perimeter.
-
Hi,
i have try to update to 1.21RC3… but i have not acomplish.
1- Download [c]DuetWiFiServer.bin[/c] from https://github.com/dc42/RepRapFirmware/tree/dev/EdgeRelease
2- Upload by web interface
3- When finish upload, star flashing, and at the end, in DWI, can see [c]WiFi Server Version: 1.21RC1[/c]
** This seems ok** NEXT
3- Download [c]DuetWiFiFirmare.bin[/c]from https://github.com/dc42/RepRapFirmware/tree/dev/EdgeRelease
4- Upload by web interface
5- But… when finish upload, can read a message: [c]M997 S0 Error: M997: In-application programming binary "iap4e.bin" not found
[/c]Where i can find [c]iap4e.bin[/c]?
Where i have to upload?
The file [c]iap4e.bin[/c] depends on the firmware you have installed? (In this moment: 1.20.1RC2 (2018-01-01))Edit: I have read Wiki and [c]iap4e.bin[/c] is in https://www.duet3d.com/wiki/Where_to_get_Duet_firmware_and_tools
-
I am having slow upload speeds via the DWC. Via FTP it works as expected but over the web control it goes to like 20 K/s speeds.
-
Hi,
I have lot's of disconnects using wifi server version 1.21 (every 2 minutes or so) but no disconnects using Wifi Server 1.20. Wifi Signal strength is quite good at -43dBm
Here are the diagnostics:
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.20
WiFi MAC address 2c:3a:e8:0b:16:1c
WiFi Vcc 3.41, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 17024
WiFi IP address 10.0.0.104
WiFi signal strength -43dBm, reconnections 0, sleep mode modem
HTTP sessions: 1 of 8
Socket states: 2 0 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) -
I am having slow upload speeds via the DWC. Via FTP it works as expected but over the web control it goes to like 20 K/s speeds.
Thanks for your feedback. Can you provide a Wireshark trace of a HTTP upload?
-
@nyt:
Any idea about the move on resume? Bug or bad script?
Are you sure that isn't a normal printing move? It looks to me that it is printing one full line of the inner perimeter.
Definitely sure. I've seen it move outside the border of the print and back. I can try to capture a better video if you'd like?
-
I am having slow upload speeds via the DWC. Via FTP it works as expected but over the web control it goes to like 20 K/s speeds.
Thanks for your feedback. Can you provide a Wireshark trace of a HTTP upload?
Sure: https://www.dropbox.com/s/4x20l1f4m59r12y/dbot.cap.pcapng?dl=0
But sems to be a lot of window errors and retransmissions. That doesn't happen with port 21/ftp.
-
any ETA for the next stable release ?
-
Next stable release will be 2 to 3 weeks from now. There will be at least one more RC first, probably two.
