New firmware 1.21RC1 available
-
I don't have any data for you but my printer went into 'slow mode' yesterday. I hadn't printed anything in a couple days before this. I used the upload and print button in DWC to print a file and after homing the print started moving VERY slowly. Like one move every minute or something. I rebooted the printer and the same gcode file printed fine. This is with a DuetWiFi.
Sorry I don't have a M122 or anything for you but I just saw this thread and I have had several successful prints since then.
I'm running 1.20, not the latest RC.
-
Hi,
I updated my duet and now i’ve noticed that the blue led on the esp8266 stays on when the duet is operational. Is there a way to turn it off, it’s quite peircing.
-
@nyt:
I notice when I pause and resume, it adds some strange extra move in after running the resume script. It's also writing a resurrect.g, not sure if it's supposed to do that on pause?
It moves back into place, then moves about 2cm out of the way at print height, then moves back.
10:40:16 PM Resume-after-power-fail state saved
This is my resume script
; Resume macro file
M83 ; relative extruder moves
G1 R1 X0 Y0 Z2 F6000 ; move to 2mm above resume point
G1 X0 Y0 Z0 R1 ; lower nozzle to resume point
G1 E12 F3600 ; undo the retractionThis is the pause script
; Pause macro file
G91 ; relative moves
M83 ; relative extruder moves
G1 E-12 F3600 ; retract 12mm
G1 X1 ;wipe
G1 Z2 F1200 ; raise nozzle 2mm
G90 ; absolute moves
G1 X0 Y300 F6000 ; move head out of the way of the printThis is video of the unintended move after the head lowers.
-
Additional information regarding the extruder motor stutter. It's rather random, but about 1/3 of retract/unretract moves exhibits this jerky movement. Its like the interrupt for driving pulses to the motors are lagging. It moves in short 'bursts' but doesn't miss steps. At some rare times the retract move is smooth but extremely slow and returns to full speed when unretracting. I'll try to shoot a little movie clip of the phenomena.
Duet 0.6 board. I haven't tried it out on the Duet WiFi yet as this printer is undergoing a complete hardware makeover right now.
-
Thanks for you report.
Regarding the printer becoming very slow, I have one other report of this, also on a Duet Ethernet. Next time it happens, please use M111 to enable GCodes, Move and DDA debugging. Then send a movement command. It will echo the gcode, then the move details, then do the move. What I am interested in is where the delay occurs.
My machine just finished a print and since I was sitting by it, I immediately commanded it to turn on relay output after it finished the end.g script. It responded quickly. However a short while after that, I attempted to home the machine and it was slow to respond.
-
Any idea about the move on resume? Bug or bad script?
-
@nyt:
Any idea about the move on resume? Bug or bad script?
Are you sure that isn't a normal printing move? It looks to me that it is printing one full line of the inner perimeter.
-
Hi,
i have try to update to 1.21RC3… but i have not acomplish.
1- Download [c]DuetWiFiServer.bin[/c] from https://github.com/dc42/RepRapFirmware/tree/dev/EdgeRelease
2- Upload by web interface
3- When finish upload, star flashing, and at the end, in DWI, can see [c]WiFi Server Version: 1.21RC1[/c]
** This seems ok** NEXT
3- Download [c]DuetWiFiFirmare.bin[/c]from https://github.com/dc42/RepRapFirmware/tree/dev/EdgeRelease
4- Upload by web interface
5- But… when finish upload, can read a message: [c]M997 S0 Error: M997: In-application programming binary "iap4e.bin" not found
[/c]Where i can find [c]iap4e.bin[/c]?
Where i have to upload?
The file [c]iap4e.bin[/c] depends on the firmware you have installed? (In this moment: 1.20.1RC2 (2018-01-01))Edit: I have read Wiki and [c]iap4e.bin[/c] is in https://www.duet3d.com/wiki/Where_to_get_Duet_firmware_and_tools
-
I am having slow upload speeds via the DWC. Via FTP it works as expected but over the web control it goes to like 20 K/s speeds.
-
Hi,
I have lot's of disconnects using wifi server version 1.21 (every 2 minutes or so) but no disconnects using Wifi Server 1.20. Wifi Signal strength is quite good at -43dBm
Here are the diagnostics:
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.20
WiFi MAC address 2c:3a:e8:0b:16:1c
WiFi Vcc 3.41, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 17024
WiFi IP address 10.0.0.104
WiFi signal strength -43dBm, reconnections 0, sleep mode modem
HTTP sessions: 1 of 8
Socket states: 2 0 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) -
I am having slow upload speeds via the DWC. Via FTP it works as expected but over the web control it goes to like 20 K/s speeds.
Thanks for your feedback. Can you provide a Wireshark trace of a HTTP upload?
-
@nyt:
Any idea about the move on resume? Bug or bad script?
Are you sure that isn't a normal printing move? It looks to me that it is printing one full line of the inner perimeter.
Definitely sure. I've seen it move outside the border of the print and back. I can try to capture a better video if you'd like?
-
I am having slow upload speeds via the DWC. Via FTP it works as expected but over the web control it goes to like 20 K/s speeds.
Thanks for your feedback. Can you provide a Wireshark trace of a HTTP upload?
Sure: https://www.dropbox.com/s/4x20l1f4m59r12y/dbot.cap.pcapng?dl=0
But sems to be a lot of window errors and retransmissions. That doesn't happen with port 21/ftp.
-
any ETA for the next stable release ?
-
Next stable release will be 2 to 3 weeks from now. There will be at least one more RC first, probably two.
