Duet3D announces new tool board at FormNext

dc42

@Exerqtor said in Duet3D announces new tool board at FormNext:

And those of us with enclosued printers pushing ABS, ASA etc. will just have to wait. A larger "issue/challenge" is the torque/accelerantion dropoff the Roto apparently has (based on Thomas Sanladerer's video).

There is speculation in the comments (which Tom hadn't denied when I looked yesterday) that the dropoff at high extrusion rates was caused at least in part by running the extruder in stealthChop mode.

Surgikill

@Exerqtor I'm still waiting on more tests. My money is on the stealthchop issue. Apparently around 300rpm is where the problem arises. I'll do some quick math to see if that is around the 8mm/s where he was experiencing drop off.

Notepad

@dc42 I cant say for certain as I have only tested the preproduction version. But I definitely didn't get the same values as Tom

Surgikill

@Surgikill said in Duet3D announces new tool board at FormNext:

@Exerqtor I'm still waiting on more tests. My money is on the stealthchop issue. Apparently around 300rpm is where the problem arises. I'll do some quick math to see if that is around the 8mm/s where he was experiencing drop off.

At 300rpm on the motor, the hobbed gear would need to be around 18mm in order to achieve 8mm/s. At 10mm/s it would need to be around 23mm. I'm not sure on the actual size, but I would bet all my money it's less than 18mm, so that motor was going well in excess of 300rpm. Definitely needs more testing.

jchodakowski

Is there any access to the printed mount parts for the Z sensor? I've seen the spacer for the tb but nothing else.

jltx

Does the roto toolboard come with scanning z probe coils? I don’t see where to get those separately.

elmoret

@jltx Yes

Edkirk

I have ordered the new tool board to install on my Voron Trident with Micro Swiss NG Extruder, E3D hotend using Duet IR Probe for Z probe. I see in the Duet 3 Roto Toolboard documentation under Firmware notes "Compatible RepRapFirmware version 3.5 or later". I updated my 6HC with SBC which only goes up to 3.4.6, is there going to be any problems using 3.4.6 or do I have to wait for 3.5?

I plan on using a Voron Tap Z-Probe with optical sensor (not Duet IR probe I am currently using) then when I have everything working converting the Tap optical to Piezo from Precision Piezo to work like the Delta Smart Effector so the Tap probe will be a true tap probe like the Delta Smart Effector. Does this configuration look like it will work? Thanks, Ed

jay_s_uk

@Edkirk you need to use 3.5. It won't work correctly with 3.4.6

dc42

@Edkirk you can install 3.5.0-rc.2 if you switch your package feed on the SBC from the stable to the unstable feed.

Edkirk

@dc42 Where do I find package feed?

Exerqtor

@Edkirk said in Duet3D announces new tool board at FormNext:

@dc42 Where do I find package feed?

Check this out 😊

Edkirk

This post is deleted!

Edkirk

This post is deleted!

Edkirk

This post is deleted!

Edkirk

This post is deleted!

Edkirk

New Duet3D tool board up and running on Voron Trident, with Tap on Z axis for homing and bed leveling. Micro Swiss NG extruder, E3d heater and nozzle.

Edkirk

Are there plans for a Delta Smart Effector with built-in Tool Board, I would install on my Delta?

demonio669

@Edkirk +1 I also want this board!!

dc42

@demonio669 @Edkirk please see https://forum.duet3d.com/topic/34657/combined-smart-effector-and-tool-board-for-delta-printers.