Unable to make first print, Error: M32:
-
I'm setting up a new Duet 3 Mainboard 6HC, with a TOOL1LC board, everything seems to work individually, but when I start to print a file I immediately get the error "Error: M32: Cannot set file to print, because a file is already being printed"
First there is no other file printing, it does seem to "start" the file, but no progress is ever made, the heaters do not turn on after any time.
If I put in the commands from the gcode file by hand, or even by a macro they work, I expect I could print the file this way, but gave up once it extruded.
I sometimes get the error "Error: Attempting to extrude with no tool selected." but not always.
Thank you for any help, anything I can do please let me know.
config.g
EDIT: in SBC mode -
@burtonenator just to sanity check: you are running RRF 3.3 but using DSF 3.4? I would recommend upgrading/downgrading to the same version for both - having such a mix might cause weird issues.
-
I would add a T0, to the end of your config.g. Depending on the slicer it might not be adding/selecting a tool at the start of the gcode file.
Follow my adventures in 3D Printing, laser cutting and electronics. https://linktr.ee/Rushmere3D
-
Printers: A FT-5 with the 713 upgrade bits, a custom MarkForged style, a small Utilmaker style, a small CoreXY from kit and a E3D MS/TC setup. Various hotends. Using Duets (2 and 3) running 3.4.6
-
I do have a T0 in the Gcode, it doesn't seem to even matter where, I tried moving it to the beginning of the file, no change.
-
@fcwilt very simple beginning code on the gcode, but even if I have a completely empty gcode file and tell it to run, it gives the same "file is already being printed" error. I don't believe any of it being run at all.
G90
M82
M106 S0
M140 S60
M190 S60
M104 S190 T0
M109 S190 T0
G28 ; home all axes
G32
; process Process1
; layer 1, Z = 0.200
T0
G92 E0.0000
G1 E-1.0000 F1800 -
-
Board: Duet 3 MB6HC (MB6HC)
DSF Version: 3.4.0
Firmware: RepRapFirmware for Duet 3 MB6HC 3.3 (2021-06-15)I can now confirm it will print if I upload the Gcode as a Macro, just not as a "job"
-
I am still using 3.3.0 so there may be a problem with 3.4.0 that I am not aware of.
Frederick
-
undefined burtonenator marked this topic as a question
-
@burtonenator just to sanity check: you are running RRF 3.3 but using DSF 3.4? I would recommend upgrading/downgrading to the same version for both - having such a mix might cause weird issues.
-
@resam
I did the update on the pi, is there more I should do, everything seems to imply all I have to do is:sudo apt update
sudo apt upgrade -
@burtonenator yes, thats the usual way - but if your system is reporting two different versions for RRF and DSF, then something went wrong.
-
Yes!, that seems to be it I got the board to upgrade to 3.4 and now its accepting a file, thank you.
-
undefined burtonenator has marked this topic as solved
-
The same problem occurred to me.
Do you happen to know how to downgrade 3.4 to 3.3?
I don't know how to do it. -
@geon-han_kang In this case they had a mismatch between DSF version and Duet firmware version.
-
@geon-han_kang I had to upgrade the duet3 to 3.4, there is a script that can help you downgrade the DSF, but I didn't use it, I wanted something from 3.4 anyways.
-
@burtonenator
Thank you.
I try that
