DUEX 5 V0.8 TO DUEX 5 V0.11

[paolozampini1973]

@droftarts you are right because you rightly want to try how it goes like this the aces if they have a loss of pace I understand what you want to do you are fine with me too you are right but unfortunately it cannot be done

[droftarts]

@paolozampini1973 Does it work after you send G92 X0 Y0 Z0?

Ian

[paolozampini1973]

@droftarts said in DUEX 5 V0.8 TO DUEX 5 V0.11:

G92 X0 Y0 Z0
I sent your message but nothing happens

[droftarts]

@paolozampini1973
Look at the Console page, there is a longer message about G28 Z.

To test endstops: send M119 in the Console. Then hold down each endstop, send M119 again. Repeat for all endstops, checking that they change state.

Ian

[paolozampini1973]

@droftarts 22/3/2022, 16:49:55 Error: short-to-ground reported by driver(s) 7 8 9
Error: over temperature shutdown reported by driver(s) 7 8 9
22/3/2022, 16:49:52 M119
Endstops - X: at min stop, Y: not stopped, Z: at max stop, Z probe: at min stop

[droftarts]

@paolozampini1973 said in DUEX 5 V0.8 TO DUEX 5 V0.11:

Endstops - X: at min stop, Y: not stopped, Z: at max stop, Z probe: at min stop

Is that with both Y endstops pressed?

Ian

[paolozampini1973]

@droftarts said in DUEX 5 V0.8 TO DUEX 5 V0.11:

@paolozampini1973 said in DUEX 5 V0.8 TO DUEX 5 V0.11:

Endstops - X: at min stop, Y: not stopped, Z: at max stop, Z probe: at min stop

Is that with both Y endstops pressed? NO

Ian

[droftarts]

@paolozampini1973 You need to press both.

Ian

[droftarts]

@droftarts Send a picture of Duet and Duex wiring.

Ian

[paolozampini1973]

@droftarts said in DUEX 5 V0.8 TO DUEX 5 V0.11:

@paolozampini1973 You need to press both.

Ian

22/3/2022, 16:55:26 M119
Endstops - X: at min stop, Y: at min stop, Z: at max stop, Z probe: at min stop

[droftarts]

@paolozampini1973 said in DUEX 5 V0.8 TO DUEX 5 V0.11:

Endstops - X: at min stop, Y: at min stop, Z: at max stop, Z probe: at min stop

Okay, that shows they are working. Post your homez.g file.

Ian

[droftarts]

@paolozampini1973 Now go back to DueX2 mode and test endstop switches again.
Turn off Duet. Remove DueX5 jumper. Turn on Duet. Test endstop switches with M119.

Ian

[paolozampini1973]

@droftarts said in DUEX 5 V0.8 TO DUEX 5 V0.11:

@paolozampini1973 said in DUEX 5 V0.8 TO DUEX 5 V0.11:

Endstops - X: at min stop, Y: at min stop, Z: at max stop, Z probe: at min stop

Okay, that shows they are working. Post your homez.g file.

Ian

[paolozampini1973]

@droftarts homez.g

[paolozampini1973]

@droftarts I have now switched to DUEX 2 mode but it does not work as the first switches

[paolozampini1973]

@droftarts driver 5 works but driver 6 doesn't work I remembered now to answer you you asked me before However this is a secondary problem

[droftarts]

@paolozampini1973 It is strange that the LED for duex.e3stop is on, when it is configured for filament sensor. Can you disconnect filament sensors from duex.e2stop and duex.e3stop, then connect Z2 endstop to duex.e2stop, then send

M574 Z2 S1 P"!zstop+!duex.e2stop"

... and then test endstops again with M119.
Ian

[paolozampini1973]

@droftarts 22/3/2022, 17:19:17 M119
Endstops - X: at min stop, Y: at min stop, Z: at max stop, Z probe: at min stop

I unplugged it the LED went out but Z does not work equally the Switches

[droftarts]

@paolozampini1973 Also, you have an always on fan wire running next to your ribbon cable. It would be a good idea to route this away from the ribbon cable. The ribbon cable has no shielding, and can pick up interference from fan and motor wires that run very close to it.

Ian

[paolozampini1973]

@droftarts said in DUEX 5 V0.8 TO DUEX 5 V0.11:

@paolozampini1973 Also, you have an always on fan wire running next to your ribbon cable. It would be a good idea to route this away from the ribbon cable. The ribbon cable has no shielding, and can pick up interference from fan and motor wires that run very close to it.

Ian

Yes I know but this was a temporary situation in the meantime to print the shells and then arrange all the cables with shielded cables You are right I agree I agree with you but as I repeat with the 08 I did not have these problems absolutely Sorry if I repeat it to you I had only a small loss of pace here the problems are so many