Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Configuration problems

    Scheduled Pinned Locked Moved
    Firmware installation
    3
    47
    1.7k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt @Dave Parry
      last edited by

      @dave-parry said in Configuration problems:

      Cant seem to get the config correct Keep getting unknown channel.
      Old config was
      M305 P0 T100000 B3950 R4700 ; set thermistor + ADC parameters for heater 0
      M143 H0 S120 ; set temperature limit for heater 0 to 120C
      M305 P1 T100000 B4388 R4700 ; set thermistor + ADC parameters for heater 1

      Have tried various settings
      latest one was
      M308 S0 P"e0temp" Y"thermistor" T100000 B4725 ; configure sensor 1 as thermistor on pin e0temp
      M950 H0 C"e0temp" T0

      get Error: Temperature reading fault on heater 1: unknown temperature sensor channel

      also tried
      M308 S0 P"e0temp" Y"thermistor" T100000 B3950 ; define E0 temperature sensor
      M950 H0 C"e0heat" T0 ; heater 1 uses the e0heat pin and sensor 1
      Error: Temperature reading fault on heater 1: unknown temperature sensor channel

      You are showing code for heater 0 but the error is for heater 1.

      What is the code for heater 1?

      Frederik

      1 Reply Last reply Reply Quote 0
      • Dave Parryundefined
        Dave Parry
        last edited by Dave Parry

        here's the code for both

        M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
        M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; define E0 temperature sensor
        M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
        M950 H1 C"e0heat" T1 ; heater 1 uses the e0heat pin and sensor 1

        Still have error heater 1
        both still showing 2000 °C

        Just changed back to old settings and temps are correct so not a sensor problem.

        fcwiltundefined 1 Reply Last reply Reply Quote 0
        • fcwiltundefined
          fcwilt @Dave Parry
          last edited by

          @dave-parry said in Configuration problems:

          here's the code for both

          M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
          M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; define E0 temperature sensor
          M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
          M950 H1 C"e0heat" T1 ; heater 1 uses the e0heat pin and sensor 1

          Still have error heater 1
          both still showing 2000 °C

          Thanks.

          Just changed back to old settings and temps are correct so not a sensor problem.

          What do you mean by "changed back to old settings"?

          Frederick

          1 Reply Last reply Reply Quote 0
          • Dave Parryundefined
            Dave Parry
            last edited by Dave Parry

            I checked the sensors by removing M308 and M960 lines and put back M305 lines. and the sensor readings were back and correct.

            fcwiltundefined 1 Reply Last reply Reply Quote 0
            • fcwiltundefined
              fcwilt @Dave Parry
              last edited by

              @dave-parry said in Configuration problems:

              I checked the sensors by removing M308 and M960 lines and put back M305 lines. and the sensor readings were back and correct.

              What firmware version are you running?

              Frederick

              1 Reply Last reply Reply Quote 0
              • Dave Parryundefined
                Dave Parry
                last edited by

                WiFi/Ethernet 2.05.1 (2020-02-09b1)

                (Thought I had upgraded to Release 3.4.0 beta 3
                but it seems that for some reason it hasn't worked.)

                Duet Web Control 3.3.0

                Will try again

                fcwiltundefined 1 Reply Last reply Reply Quote 0
                • Dave Parryundefined
                  Dave Parry
                  last edited by

                  Just tried again and the machine specific tab still says 2.05

                  1 Reply Last reply Reply Quote 0
                  • fcwiltundefined
                    fcwilt @Dave Parry
                    last edited by

                    @dave-parry said in Configuration problems:

                    WiFi/Ethernet 2.05.1 (2020-02-09b1)

                    (Thought I had upgraded to Release 3.4.0 beta 3
                    but it seems that for some reason it hasn't worked.)

                    Duet Web Control 3.3.0

                    Will try again

                    Remember that you have to first go from 2.05.1 to 3.0.0

                    Frederick

                    1 Reply Last reply Reply Quote 0
                    • Dave Parryundefined
                      Dave Parry
                      last edited by

                      Tried 3.1 combined.bin Cant seem to upload it.

                      fcwiltundefined 1 Reply Last reply Reply Quote 0
                      • fcwiltundefined
                        fcwilt @Dave Parry
                        last edited by

                        @dave-parry said in Configuration problems:

                        Tried 3.1 combined.bin Cant seem to upload it.

                        3.1?

                        So you got it up to 3.0 already?

                        Frederick

                        1 Reply Last reply Reply Quote 0
                        • Dave Parryundefined
                          Dave Parry
                          last edited by

                          No I hadnt but have now. When I looked down the list 3.1 was above 2.05 and 3.0 was below and I didnt see it.

                          fcwiltundefined 1 Reply Last reply Reply Quote 1
                          • fcwiltundefined
                            fcwilt @Dave Parry
                            last edited by

                            @dave-parry said in Configuration problems:

                            No I hadnt but have now. When I looked down the list 3.1 was above 2.05 and 3.0 was below and I didnt see it.

                            You now should be able to go to 3.3.0 or (if you ok with betas) to 3.4.x.

                            Frederick

                            1 Reply Last reply Reply Quote 0
                            • Dave Parryundefined
                              Dave Parry
                              last edited by Dave Parry

                              Thanks Frederick.
                              Cant get 3.4 to install. Get Error: In-application programming binary "Duet2CombinedIAP.bin" not found

                              Temps are working now but still have problem that cant set heaters to active

                              Have tried all the way back to 3.2. Same error message

                              fcwiltundefined 1 Reply Last reply Reply Quote 0
                              • Dave Parryundefined
                                Dave Parry
                                last edited by

                                Got it done now at WiFi/Ethernet 3.4.0beta3 (2021-08-24)

                                fcwiltundefined 1 Reply Last reply Reply Quote 0
                                • fcwiltundefined
                                  fcwilt @Dave Parry
                                  last edited by fcwilt

                                  This post is deleted!
                                  1 Reply Last reply Reply Quote 0
                                  • fcwiltundefined
                                    fcwilt @Dave Parry
                                    last edited by

                                    @dave-parry said in Configuration problems:

                                    Got it done now at WiFi/Ethernet 3.4.0beta3 (2021-08-24)

                                    Glad to hear it.

                                    Frederick

                                    1 Reply Last reply Reply Quote 0
                                    • Dave Parryundefined
                                      Dave Parry
                                      last edited by Dave Parry

                                      OK so Hot end now goes Off Active and standby, but Bed not showing up and these error messages
                                      G28
                                      Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
                                      Error: Failed to enable endstops

                                      fcwiltundefined 1 Reply Last reply Reply Quote 0
                                      • Dave Parryundefined
                                        Dave Parry
                                        last edited by

                                        Oh and no fan controls showing up

                                        1 Reply Last reply Reply Quote 0
                                        • fcwiltundefined
                                          fcwilt @Dave Parry
                                          last edited by

                                          @dave-parry said in Configuration problems:

                                          OK so Hot end now goes Off Active and standby, but Bed not showing up and these error messages

                                          Do you have this command after the M950 for the bed heater?

                                          M140 P0 H0 ; map heated bed to heater 0

                                          G28

                                          Warning: Obsolete use of S parameter on G1 command. Use H parameter instead.
                                          Error: Failed to enable endstops

                                          Correct.

                                          What used to be G1 S1 is now G1 H1.

                                          Just edit your homing files.

                                          Frederick

                                          1 Reply Last reply Reply Quote 0
                                          • Dave Parryundefined
                                            Dave Parry
                                            last edited by

                                            Have bed temps working now, many thanks.
                                            Homing not working because of end stops Not enabled.
                                            Is that similar to temp sensors?

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA