Configuration problems

JawsN3D

@dave-parry
Yeah it appears you need to convert your heater and end stops to the proper rrf 3.0+ syntax unless you go to v 2.03/2.05

A few things have changed...
M305 is no longer used

Dave Parry

Thanks, I did use the latest config tool so would have thought it would be correct. Will see if I can sort it out.

JawsN3D

@dave-parry

I'm on my phone and can't post my config. But in the post adjacent to yours mentioning print finished.....You can look at my config of the end stops for a refrence

Edit. If you look at the first post config. G you will see I left all of my earlier 2.03 syntax settings and configurations but they are commented out. That was from all of my work converting to the new system and it might prove helpful for you as it has for me. The config. G lower on in the thread is after I did some house cleaning got rid of all of the extraneous lines

Dave Parry

Cant seem to get the config correct Keep getting unknown channel.
Old config was
M305 P0 T100000 B3950 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4388 R4700 ; set thermistor + ADC parameters for heater 1

Have tried various settings
latest one was
M308 S0 P"e0temp" Y"thermistor" T100000 B4725 ; configure sensor 1 as thermistor on pin e0temp
M950 H0 C"e0temp" T0

get Error: Temperature reading fault on heater 1: unknown temperature sensor channel

also tried
M308 S0 P"e0temp" Y"thermistor" T100000 B3950 ; define E0 temperature sensor
M950 H0 C"e0heat" T0 ; heater 1 uses the e0heat pin and sensor 1
Error: Temperature reading fault on heater 1: unknown temperature sensor channel

fcwilt

@dave-parry said in Configuration problems:

Cant seem to get the config correct Keep getting unknown channel.
Old config was
M305 P0 T100000 B3950 R4700 ; set thermistor + ADC parameters for heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4388 R4700 ; set thermistor + ADC parameters for heater 1

Have tried various settings
latest one was
M308 S0 P"e0temp" Y"thermistor" T100000 B4725 ; configure sensor 1 as thermistor on pin e0temp
M950 H0 C"e0temp" T0

get Error: Temperature reading fault on heater 1: unknown temperature sensor channel

also tried
M308 S0 P"e0temp" Y"thermistor" T100000 B3950 ; define E0 temperature sensor
M950 H0 C"e0heat" T0 ; heater 1 uses the e0heat pin and sensor 1
Error: Temperature reading fault on heater 1: unknown temperature sensor channel

You are showing code for heater 0 but the error is for heater 1.

What is the code for heater 1?

Frederik

Dave Parry

here's the code for both

M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0heat" T1 ; heater 1 uses the e0heat pin and sensor 1

Still have error heater 1
both still showing 2000 °C

Just changed back to old settings and temps are correct so not a sensor problem.

fcwilt

@dave-parry said in Configuration problems:

here's the code for both

M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 ; define bed temperature sensor
M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; define E0 temperature sensor
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M950 H1 C"e0heat" T1 ; heater 1 uses the e0heat pin and sensor 1

Still have error heater 1
both still showing 2000 °C

Thanks.

Just changed back to old settings and temps are correct so not a sensor problem.

What do you mean by "changed back to old settings"?

Frederick

Dave Parry

I checked the sensors by removing M308 and M960 lines and put back M305 lines. and the sensor readings were back and correct.

fcwilt

@dave-parry said in Configuration problems:

I checked the sensors by removing M308 and M960 lines and put back M305 lines. and the sensor readings were back and correct.

What firmware version are you running?

Frederick

Dave Parry

WiFi/Ethernet 2.05.1 (2020-02-09b1)

(Thought I had upgraded to Release 3.4.0 beta 3
but it seems that for some reason it hasn't worked.)

Duet Web Control 3.3.0

Will try again

Dave Parry

Just tried again and the machine specific tab still says 2.05

fcwilt

@dave-parry said in Configuration problems:

WiFi/Ethernet 2.05.1 (2020-02-09b1)

(Thought I had upgraded to Release 3.4.0 beta 3
but it seems that for some reason it hasn't worked.)

Duet Web Control 3.3.0

Will try again

Remember that you have to first go from 2.05.1 to 3.0.0

Frederick

Dave Parry

Tried 3.1 combined.bin Cant seem to upload it.

fcwilt

@dave-parry said in Configuration problems:

Tried 3.1 combined.bin Cant seem to upload it.

3.1?

So you got it up to 3.0 already?

Frederick

Dave Parry

No I hadnt but have now. When I looked down the list 3.1 was above 2.05 and 3.0 was below and I didnt see it.

fcwilt

@dave-parry said in Configuration problems:

No I hadnt but have now. When I looked down the list 3.1 was above 2.05 and 3.0 was below and I didnt see it.

You now should be able to go to 3.3.0 or (if you ok with betas) to 3.4.x.

Frederick

Dave Parry

Thanks Frederick.
Cant get 3.4 to install. Get Error: In-application programming binary "Duet2CombinedIAP.bin" not found

Temps are working now but still have problem that cant set heaters to active

Have tried all the way back to 3.2. Same error message

Dave Parry

Got it done now at WiFi/Ethernet 3.4.0beta3 (2021-08-24)

fcwilt

This post is deleted!

fcwilt

@dave-parry said in Configuration problems:

Got it done now at WiFi/Ethernet 3.4.0beta3 (2021-08-24)

Glad to hear it.

Frederick