HELP! Duet 2 WiFi Configuration and DWC Upload???
-
Just to be sure I copied all of my files to a new Micro SD and I'm getting the same result/issue.
404 Not Found
-
@pcnoobneedsmajorhelp said in HELP! Duet 2 WiFi Configuration and DWC Upload???:
Through the PanelDue I sent the M122 and I got this message
Unfortunately the PAnelDue doesn't have enough text space to show the full report and the wifi info is near the end, so you'd need to check from USB terminal.
Though if you send M552 it should be able to tell you if you have an IP address or not.
With the SD card in the socket you can also send M22 to unmount, M21 to mount to the card. And then send
M122 P104 S10to test if the SD card is working ok with a test write. -
Ok so i did that and got this
so if i connect via USB what program should I open? YAT, Arduino, Visual Studio Code?
-
YAT would be the correct way to interface over USB terminal.
-
So I'm trying to use YAT but I'm not getting anywhere. my COM Port isn't being detected. I'm lost when it comes to terminals
-
You've got the board connected via usb to the PC, right?
The USB cable must carry data, not just power.
When you plug it in, does the board light up the 5v LED?
Does windows detect a device has been connected?
Try different cables/usb ports
-
-
Ok, so SD card and wifi appear to be working, at least at that moment.
But still no DWC?
What is in the /www/ folder on the SD card?
Is the config.g file still in the /sys/ folder?
-
Just out of curiosity I tried out a few IP Addresses, and somehow the IP was changed. I don't know how, but its working under a different IP now. But it is working.
yeah config.g and www are both on the card
-
Well if the IP address is DHCP from the router there is a chance it could change occasionally. The best thing to do would be to set up a IP reservation in the router config so that it doesn't change.
-
How do I do that?
-
That will depend entirely on your router.
-
ok I'll look into it
-
Thanks
-
If you can find a manual it would probably be found under "DHCP reservation".
-
So I'm testing some new filaments, and on the technical data sheet it says for the print bed to be at 140°c. I'm almost positive mine maxes out at 110, which means i need to upgrade. Do you have any suggestions.
I was thinking these (one generic, one brand)
https://www.amazon.com/gp/product/B07GJGCBNP/ref=ox_sc_act_title_1?smid=AJUKUXZVPYM6H&psc=1
What's your take on it?
Thanks,
-Carson
-
Keenovo has a good reputation and I wouldn't bother with anything else.
There are lots of places to be cheap, but power supplies and heaters aren't one of them.
-
@Phaedrux
(I decided to reply to this thread so you'd remember me)Hey...It's been a while. After a very busy year I'm finally ready to install my Keenovo Heated bed upgrade. I think I got the wrong heated bed though. I have a 24v 350w Keenovo, and I have a 24v 350w power supply as well as an SSR. I was reading up on the stock heated bed for the Ender 5 and it's a 24v 350w bed as well (facepalm). I'm realizing now that I should have gotten a 110v 500w heated pad for higher temperatures for my bed plate where I would be pulling power from the Mains on my PSU rather than the 24 volts it supplies to the rest of the Duet. Am I correct in my thinking?
Thanks in advance for any guidance
-
@PCNoobNeedsMajorHelp Please start a new thread for a new subject; this thread is already 200 posts long! You can always reference this original thread from the new one.
Ian
-
Do you want me to post another one for this question or just for next time?
