DWC 3.1.1
-
VORREI USARE REPETIER HOST TRAMITE WIFI , NON SO COME FARE , MI PUOI INDIRIZZARE ?
-
@luca-Massimiliano said in DWC 3.1.1:
I WOULD LIKE TO USE REPETIER HOST VIA WIFI, I DON'T KNOW HOW TO DO IT, CAN YOU ADDRESS ME?
I do not know how to use repetier host.
-
COSA USI PER STAMPARE?
-
I upload the sliced file directly from the slicer to the Duet over the network.
-
@luca-Massimiliano You upload gcode files to the 'Jobs' screen in DWC, print from there!
See: https://duet3d.dozuki.com/Wiki/Duet_Web_Control_v2_and_v3_(DWC)_Manual#Section_JobsIan
Cartesian bed-slinger with Duet 3 Mini 5+ WiFi and 1LC : RRP Fisher Delta v1 with Duet 2 Maestro : TronXY X5S with Duet 3 MB6HC and Roto toolboard
-
-
@droftarts STL OK?
-
@luca-Massimiliano No. You need to 'slice' the stl first, with something like Cura or PrusaSlicer, to make a gcode file, then upload that. I think Repetier Server does this for you, but then it transfers the gcode to the Duet by USB (or Telnet over Ethernet/WiFi, which should be faster), as it's printing, which can cause pausing problems.
Most people prefer to have control over the slicing of the stl to gcode, so use a separate program to do this. Repetier Server takes away this control, to make it easier to use. Up to you.
Ian
-
TI RINGRAZIO MA RIPRENDERO DOPO LA STAMPA DIRETTA
-
IL MIO INIZIALE PROBLEMA PRIMA DI ADGIORNARE TUTTA LA MACCHINA COSA CHE SONO CONTENTISSIMO E RINGRAZIO TUTTI MA IN PARTICOLAR MODO PHAEDRUX PHAEDRUX. E' IL SEGUENTE , IL RISCALDATORE T1 NON VIENE RICONOSCIUTO REPETIER NE DA PRONTERFACE 
-
This post is deleted! -
@leblond are you available for some italian translation?
-
-
NON RIESCO INSERIRE PIU' FOTO
-
IL RISCALDATORE T1 NON VIENE RICONOSCIUTO DA REPETIER NE DA PRONTERFACE ! ECCO LA FOTO DELLA SCHEDA https://duet3d.dozuki.com/Wiki/Hardware_Overview#Section_Firmware_notes
IL RISCALDATORI SONO NOMINATI E1 E0 E BED IN TUTTE LE APPLICAZIONI ,VENGONO NOMINATI E1 E2 E IL BED NOMINATO E0 QUINDI NON VORREI CHE SI CREI UN CONFLITTO , -
QUI SONO GIUSTI:
M308 S0 P"bedtemp" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4388 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C
M308 S2 P"e1temp" Y"thermistor" T100000 B4388 ; configure sensor 2 as thermistor on pin e1temp
M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H2 S280 ; set temperature limit for heater 2 to 280C -
I don't know anything about proterface or repetier. I would suggest you use DWC to interact with the printer.
-
PER ME NON E' NECESSARIO USARE QUESTE APPLICAZIONI , SOLO CHE VOLEVO FARE UNA PROVA E CON IL NOSTRO DUET NON SO ANCORA USARLO ORA MI METTERO' A STUDIARE E USERO' SOLO DUET . PER LE TRADUZIONI DISONIBILE
-
This may be your best guide for learning the Duet interface.
https://duet3d.dozuki.com/Wiki/Duet_Web_Control_v2_and_v3_(DWC)_Manual
-
This may be your best guide for learning the Duet interface.
grazie 1000
