New to the duet COMPLETE NEWBIE
-
@Phaedrux
M308 S1 P"e1temp" Y"thermistor" T98801 B4185 ; configure sensor 1 as thermistor on pin e1temp
M950 H1 C"e1heat" T1 ; create nozzle heater output on e1heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limitI think its this line here maybe??
M143 H1 S80 ; set temperature limit for heater 1 to 80C -
@Phaedrux Fixed it and was able to get it heated up to 180,
Now when i try to get the bed heated i get thisError: Heater 0 fault: temperature rising much more slowly than the expected 1.8°C/sec
-
@Phaedrux Okay i looked up the issue and found YOU lol, going to PID tune the bed. .
-
We're on a roll!
-
@Phaedrux Good morning from my end. we definitely were on a roll yesterday. I did a PID test for the heated bed and this is what I got,
1/20/2021, 7:25:49 PM M500
1/20/2021, 7:25:31 PM M307 H0 R0.208 C535.3 D7.42 S1.00 V12.0
Warning: M307: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 136C
1/20/2021, 7:23:29 PM Warning: heater behaviour was not consistent during tuning
Auto tuning heater 0 completed after 3 idle and 25 tuning cycles in 4384 seconds. This heater needs the following M307 command:
M307 H0 R0.208 C535.3 D7.42 S1.00 V12.0
Send M500 to save this command in config-override.gAt this point I don't know what to do.
EDIT: indeed i do, Ill go back in to the shop and tune the hotend as well and try to run the min temps for PLA. . hopefully i dont get any errors. I will let you know once i am finished. -
you send M500 to save the tuning parameters.
-
@Veti
Yes i sent it after both test were performed. Here is the summary for both1/21/2021, 10:15:03 AM M500
1/21/2021, 10:14:47 AM M307 H1 R2.273 C141.1 D6.29 S1.00 V12.0
1/21/2021, 10:14:20 AM Auto tuning heater 1 completed after 3 idle and 5 tuning cycles in 401 seconds. This heater needs the following M307 command:
M307 H1 R2.273 C141.1 D6.29 S1.00 V12.0
Send M500 to save this command in config-override.g
1/21/2021, 10:11:54 AM Auto tune starting phase 3, fan off
1/21/2021, 10:09:52 AM Auto tune starting phase 2, heater settling
1/21/2021, 10:07:44 AM Auto tune starting phase 1, heater on1/21/2021, 10:07:39 AM M303 H1 S210
Auto tuning heater 1 using target temperature 210.0°C and PWM 1.00 - do not leave printer unattended
1/21/2021, 10:06:23 AM M106 S127
1/21/2021, 10:00:22 AM Connection established
1/20/2021, 7:27:51 PM Connection interrupted, attempting to reconnect...
HTTP request timed out
1/20/2021, 7:25:49 PM M500
1/20/2021, 7:25:31 PM M307 H0 R0.208 C535.3 D7.42 S1.00 V12.0
Warning: M307: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 136C
1/20/2021, 7:23:29 PM Warning: heater behaviour was not consistent during tuning
Auto tuning heater 0 completed after 3 idle and 25 tuning cycles in 4384 seconds. This heater needs the following M307 command:
M307 H0 R0.208 C535.3 D7.42 S1.00 V12.0
Send M500 to save this command in config-override.g
1/20/2021, 6:22:39 PM Auto tune starting phase 3, fan off
1/20/2021, 6:14:17 PM Auto tune starting phase 2, heater settling
1/20/2021, 6:10:31 PM Auto tune starting phase 1, heater on
1/20/2021, 6:10:25 PM M303 H0 S60
Auto tuning heater 0 using target temperature 60.0°C and PWM 1.00 - do not leave printer unattended -
i was talking about the delta calibration
-
the new hotend tuning command is
M303 T0 S210 -
@Veti Ohhh , Okay. Im about to do a new one now then . THANKKK YOUUUUUUU!!!
-
M303 T0 S210 will tune the hotend heater and take the part cooling fan into account.
For the bed heater, the M303 H0 S60 is correct.
1/20/2021, 7:23:29 PM Warning: heater behaviour was not consistent during tuning
Not sure why you're getting that though. What kind of bed heater do you have on the CR-10? Stock? Are you starting from room temp?
Do the saved tuning results allow for you to heat the bed to 60 in a reasonable time and keep a consistent temp? If so, that's all that really matters.
-
@Phaedrux Big baby is doing better, i got her up to 50 and she held it pretty well. Thank you!! Ill keep you updated though
-
@Phaedrux should i be concerned if the MCU temp is up to 27.6?
-
Probably not, but first make sure it's an accurate temp.
https://duet3d.dozuki.com/Wiki/Calibrating_the_CPU_temperature
With a bit of forced air cooling even after a long print it doesn't get much above 35 for me. And you really only need to worry about 80+ The drivers get hotter and need more cooling than the MCU, but the MCU temp can be used as a proxy for the driver temps and allow for using a thermostatically controlled fan. All described in this link.
https://duet3d.dozuki.com/Wiki/Mounting_and_cooling_the_board
-
@Phaedrux I hooked one up and its good now. .
I tried to print the calibration box and my Extruder wasn't close to my bed at all still trying to print. . also when i try to home XYZ it states its "busy" and waits about 3-5 mins to move at all. . . idk what to do. Is it something id have to change within my config? -
Please post your current config.g and homeall.g and copy and paste the first 50 lines or so of your sliced gcode file you're trying to print.
-
; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 19 2021 17:33:25 GMT-0500 (Eastern Standard Time); General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Creola" ; set printer name; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E97.08 ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z600.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z120.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X300 Y300 Z400 S0 ; set axis maxima; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z1 S1 P"!zstop" ; configure active-high endstop for low end on Z via pin !zstop; Z-Probe
M558 P0 H18 F120 T480000 ; disable Z probe but set dive height, probe speed and travel speed
M557 X10:220 Y10:220 S20 ; define mesh grid; Heaters
M308 S0 P"bedtemp" Y"thermistor" T98801 B4185 ; configure sensor 0 as thermistor on pin e0temp
M950 H0 C"bedheat" T0 ; create bed heater output on e0heat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S80 ; set temperature limit for heater 0 to 80C
M308 S1 P"e1temp" Y"thermistor" T98801 B4185 ; configure sensor 1 as thermistor on pin e1temp; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.1 on Tue Jan 19 2021 17:33:25 GMT-0500 (Eastern Standard Time)
G91 ; relative positioning
G1 H2 Z18 F480000 ; lift Z relative to current position
G1 H1 X-305 Y-305 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F480000 ; go back a few mm
G1 H1 X-305 Y-305 F3600 ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-405 F3600 ; move Z down stopping at the endstop
G90 ; absolute positioning
G92 Z0 ; set Z position to axis minimum (you may want to adjust this); Uncomment the following lines to lift Z after probing
;G91 ; relative positioning
;G1 Z18 F8000 ; lift Z relative to current position
;G90 ; absolute positioning;FLAVOR:Marlin
;TIME:15708
;Filament used: 30.0079m
;Layer height: 0.32
;MINX:87.5
;MINY:87.5
;MINZ:0.32
;MAXX:212.5
;MAXY:212.5
;MAXZ:99.84
;Generated with Cura_SteamEngine 4.8.0
M140 S45
M105
M190 S45
M104 S210
M105
M109 S210
M82 ;absolute extrusion mode
M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
M220 S100 ;Reset Feedrate
M221 S100 ;Reset FlowrateG28 ;Home
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis upG92 E0
G92 E0
G1 F2700 E-5
;LAYER_COUNT:312
;LAYER:0
M107
G0 F6000 X96.919 Y97.136 Z0.32
;TYPE:SKIRT
G1 F2700 E0
G1 F1200 X97.194 Y96.861 E0.05174
G1 X97.565 Y96.502 E0.12042
G1 X97.79 Y96.289 E0.16164
G1 X98.257 Y95.859 E0.2461
G1 X98.563 Y95.587 E0.30057 -
@gabrealek said in New to the duet COMPLETE NEWBIE:
M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup JerkDelete these lines from your cura start gcode.
@gabrealek said in New to the duet COMPLETE NEWBIE:
;FLAVOR:Marlin
Also in Cura change your gcode flavour to REPRAP
Also change cura to use relative extrusion while you're at it.
Then reslice and try again.
-
@Phaedrux I feel like such a nube, thanks again!! Im about to try now and keep you updated.
-
Don't feel too bad, 3D printing is probably one of the most complicated hobbies you can pick up.
